On Wed, 2017-03-29 at 07:21 +0200, Takashi Iwai wrote:
On Tue, 28 Mar 2017 22:10:28 +0200, Tanu Kaskinen wrote:
On Fri, 2017-03-24 at 23:01 +0100, Hans de Goede wrote:
Hi,
On 03/24/2017 07:18 PM, Tanu Kaskinen wrote:
On Thu, 2017-03-23 at 09:57 +0100, Takashi Iwai wrote:
On Thu, 23 Mar 2017 04:16:52 +0100, Pierre-Louis Bossart wrote:
On 3/21/17 2:56 AM, Hans de Goede wrote: > I: [pulseaudio] alsa-sink.c: Using 1.0 fragments of size 352832 bytes > (2000.18ms), buffer size is 352832 bytes (2000.18ms) > I: [pulseaudio] alsa-sink.c: Time scheduling watermark is 20.00ms > I: [pulseaudio] alsa-sink.c: Driver does not support hardware volume > control, falling back to software volume control. > I: [pulseaudio] alsa-sink.c: Driver does not support hardware mute > control, falling back to software mute control. > I: [alsa-sink-HdmiLpeAudio] core-util.c: Successfully enabled SCHED_RR > scheduling for thread, with priority 5. > I: [alsa-sink-HdmiLpeAudio] alsa-sink.c: Starting playback. > I: [alsa-sink-HdmiLpeAudio] (alsa-lib)pcm_hw.c: SNDRV_PCM_IOCTL_HWSYNC > failed (-32)
Humm, single period and hw_sync failed, this could be testing the robustness of the single-period code and its mapping on multiple DMA descriptors? I haven't looked at the alsa module in eons but can't the number of periods be forced to two with module parameters while keeping the timer-based schedulng?
I think the code doesn't currently support this.
It's -EPIPE and this is supposed to be the intentional error code from HDMI LPE audio driver. The streaming doesn't work when the gfx is disconnected or the monitor audio is off. It accepts the open, but it returns -EPIPE for further accesses.
Maybe -EPIPE is no sensible choice, but the problem is that the driver can't use the PCM DISCONNECT state because PA interprets it being the complete disconnection of the card object instead of a temporary disablement of PCM.
So is this a PulseAudio bug?
I: [alsa-sink-HdmiLpeAudio] alsa-sink.c: Starting playback. I: [alsa-sink-HdmiLpeAudio] (alsa-lib)pcm_hw.c: SNDRV_PCM_IOCTL_HWSYNC failed (-32)
The "Starting playback" message is printed just before the snd_pcm_start() call. PulseAudio doesn't check the return value of snd_pcm_start(), but maybe it should? Does the HWSYNC happen in snd_pcm_start()?
Can this EPIPE thing happen also during playback, not just when starting?
So is this the likely cause of the RT code killing pa, or do you still need me to gather perf output ?
The perf output would be interesting.
It's still unclear to me if the hwsync thing is a bug in alsa, or something that pulseaudio should deal with. If there's no further input from the alsa developers, would you be able to test a pulseaudio patch if I write one? First I'd like to check whether the hwsync error happens inside snd_pcm_start(), and if so, does the error get reported in the snd_pcm_start() return value. If snd_pcm_start() returns an error, pulseaudio should probably react to it, although I'm not sure how. It would be easy to just remove the sink if there's an error, but I understood Takashi's comment so that it might be an intermittent error that depends on the graphics state, and if that's the case, pulseaudio would have to retry when the graphics state changes, but I don't know what kind of event could be used to get a notification about the state change.
Does PA really need to start streaming at its invocation time? The crash happens when PA gets started via desktop autostart, and at this moment, the HDMI graphics state is possible disconnected before xrandr setup. The HDMI connection state should have been informed / notified to PA via the jack interface, so it should be possible to judge beforehand.
Or it might be something wrong in the driver side regarding the jack state processing?
I had a closer look at the PA log that was posted earlier. It looks like the device numbering is non-standard. Trying to open any of the hdmi:1,x devices fails. hw:1 can be opened, and pulseaudio assumes that it's an analog stereo device. Jack detection isn't going to work in this situation, because pulseaudio doesn't know that it should be looking at the hdmi jacks.
Can the driver be fixed to use the standard HDMI device numbers?