Re: [alsa-devel] [PATCH v6 5/6] dt-bindings: display: sii902x: Add HDMI audio bindings

On Tue, Apr 02, 2019 at 10:29:14AM +0300, Jyri Sarha wrote:

The sii902x chip family supports also HDMI audio. Add binding for describing the necessary i2s and mclk wiring for it.

Signed-off-by: Jyri Sarha jsarha@ti.com

.../bindings/display/bridge/sii902x.txt | 37 +++++++++++++++++++ 1 file changed, 37 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt index c4c1855ca654..d124a5fedab1 100644 --- a/Documentation/devicetree/bindings/display/bridge/sii902x.txt +++ b/Documentation/devicetree/bindings/display/bridge/sii902x.txt @@ -9,6 +9,37 @@ Optional properties: about hotplug events.

• reset-gpios: OF device-tree gpio specification for RST_N pin.

• HDMI audio properties:
• • #sound-dai-cells: <0> or <1>. <0> if only i2s or spdif pin

•   is wired, <1> if the both are wired. HDMI audio is
  

•   configured only if this property is found.
  

• • sil,i2s-data-lanes: Array of up to 4 integers with values of 0-3

•   Each integer indicates which i2s pin is connected to which
  

•   audio fifo. The first integer selects i2s audio pin for the
  

•   first audio fifo#0 (HDMI channels 1&2), second for fifo#1
  

•   (HDMI channels 3&4), and so on. There is 4 fifos and 4 i2s
  

•   pins (SD0 - SD3). Any i2s pin can be connected to any fifo,
  

•   but there can be no gaps. E.g. an i2s pin must be mapped to
  

•   fifo#0 and fifo#1 before mapping a channel to fifo#2. Default
  

•   value is <0>, describing SD0 pin beiging routed to hdmi audio
  

•   fifo #0.
  

• • clocks: phandle and clock specifier for each clock listed in

•       the clock-names property
  

• • clock-names: "mclk"

•   Describes SII902x MCLK input. MCLK is used to produce
  

•   HDMI audio CTS values. This property is required if
  

•   "#sound-dai-cells"-property is present. This property follows
  

•   Documentation/devicetree/bindings/clock/clock-bindings.txt
  

•   consumer binding.
  

• If HDMI audio is configured the sii902x device becomes an ASoC
• codec component, that can be used in configuring full audio
• devices with ASoC simple-card or audio-graph-card. See their

ASoC is a Linux thing.

• binding documents on how to describe how the sii902x device is
• connected to the rest of the audio system:
• Documentation/devicetree/bindings/sound/simple-card.txt
• Documentation/devicetree/bindings/sound/audio-graph-card.txt

Optional subnodes:

• video input: this subnode can contain a video input port node to connect the bridge to a display controller output (See this

@@ -21,6 +52,12 @@ Example: compatible = "sil,sii9022"; reg = <0x39>; reset-gpios = <&pioA 1 0>;

• #sound-dai-cells = <0>;
  

• i2s-data-lanes = < 0 1 2 >;
  

• clocks = <&mclk>;
  

• clock-names = "mclk";
  

• ports { #address-cells = <1>; #size-cells = <0>;

-- Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki