Additionally, I noticed that the results file from 'alsa-info.sh' the section about Module is does now show "macpro" under the model section.
Might I be doing something wrong? < snippet > ....
!!Module: snd_hda_intel bdl_pos_adj : 1,-1,-1,-1,-1,-1,-1,-1 enable : Y,Y,Y,Y,Y,Y,Y,Y enable_msi : 0 id : <NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL> index : -1,-1,-1,-1,-1,-1,-1,-1 model : <NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL>,<NULL> position_fix : 0,0,0,0,0,0,0,0 power_save : 0 power_save_controller : Y probe_mask : -1,-1,-1,-1,-1,-1,-1,-1 single_cmd : N .... < snippet >
// Salvador // Northwestern Univeristy
----- Original Message ---- From: Takashi Iwai tiwai@suse.de To: S. Aguinaga sa_jr@ieee.org Cc: alsa-devel@alsa-project.org Sent: Tuesday, August 19, 2008 5:48:47 AM Subject: Re: [alsa-devel] Alsa-devel Digest, Vol 18, Issue 45
At Mon, 18 Aug 2008 10:26:42 -0700 (PDT), S. Aguinaga wrote:
============================================== Trying to figure out where to add this "model=macpro" and it looks like it should be in a file called modprobe.conf or an options file under /etc/modprobe.d/
but I don't have (with my installation -- fedora {9} ) those files, do you have any input on this?
You can create any file, typically, /etc/modprobe.d/sound or so. Put the following line there
options snd-hda-intel model=macpro
Then reload the module, check the sysfs file /sys/modules/snd_hda_intel/parameters/macpro to see whether the specified option was really passed properly.
Takashi
below are the only files I have.
/etc/modprobe.d/
anaconda blacklist-visor i915modeset blacklist floppy-pnp modprobe.conf.dist
============================================== Subject: Re: [alsa-devel] Alsa-devel Digest, Vol 18, Issue 45
At Sat, 16 Aug 2008 06:15:46 -0700 (PDT), S. Aguinaga wrote:
S. Aguinaga wrote:
Hello Stan,
This is awesome I did find the problem it's listed in the /var/log/messages under ALSA.
- When I bring up the "Pulse Volume Control" gui, the first tab "Playback" comes up empty, and grayed-out is "No Streams Available"
- aplay does not produce sound, period!
- Amrok's welcome sample does not produce sound out of the std tower speaker or the headphone jack.
I didn't notice anything strange on the output of the alsa-info.sh file, but when I checked the var/log/messages, this is what I found:
sudo cat /var/log/messages | grep ALSA Aug 11 07:52:10 macprolinx kernel: ALSA sound/pci/hda/hda_intel.c:1810: chipset global capabilities = 0x4401 Aug 11 07:52:10 macprolinx kernel: ALSA sound/pci/hda/hda_intel.c:749: codec_mask = 0x1 Aug 11 07:52:10 macprolinx kernel: ALSA sound/pci/hda/hda_codec.c:1073: Cannot find slave Surround Playback Volume, skipped
(snip)
These messages are harmless. It's just information from the driver, enabled only when you build it with CONFIG_SND_DEBUG_VERBOSE=y.
I think your problem is a misidentification of your sound chip. The model being used for your 889A appears to be incompatible, thus all the errors above. It appears that the macpro ALC885 is being selected before it gets to the choice for the ALC889A. Perhaps a developer can look into this.
Well, ALC882, ALC885 and ALC889A are almost compatible. In the driver, they are all handled in the same routine.
There are a few models for intel macs with ALC88x. Try to specify either model=macpro, model=mbp3 or model=imac24 as the module option of snd-hda-intel driver.
Takashi