2011/11/22 Julian Sikorski belegdol@gmail.com:
W dniu 22.11.2011 06:17, Raymond Yau pisze:
2011/11/21 Julian Sikorski belegdol@gmail.com:
W dniu 21.11.2011 07:47, Raymond Yau pisze:
2011/11/19 Julian Sikorski belegdol@gmail.com:
> From the official (non-service) manual, page 309: >
Refer to P170HM 's photo in user manual
There are 3 speakers and a subwoofer at the bottom of the laptop and two speakers at the top
Refer to user manual of P150HM,
Plug the front speaker cables into the Headphone-Out Jack.
• Line-In Jack = Rear Speaker Out • Microphone-In Jack = Center/Subwoofer Speaker Out • S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only)
You may need to ask Takashi , David, PA developers and Media controller developers how to handle this case
since it may need to set_pin_ctl to PIN_HP and PIN_OUT of 0x1b and retasking of input jacks as output whether PA or Media controller API expect to change the name of the volume control and switch from "Headphone" to "Front" by hda-reconfig
http://thread.gmane.org/gmane.linux.alsa.devel/91334
- As you plug in each cable a dialog box will pop up (see “Auto Popup
Dialog” on page 2 - 9).
Auto Popup Dialog mean support jack detect
you can try David's hda-jack-sense-test.py
Yes, it is working: [julas@snowball2 ~]$ sudo python hda-jack-sense-test.py Pin 0x18 (Black Mic): present = No Pin 0x1a (Black Line In): present = No Pin 0x1b (Black HP Out): present = Yes [julas@snowball2 ~]$ sudo python hda-jack-sense-test.py Pin 0x18 (Black Mic): present = No Pin 0x1a (Black Line In): present = No Pin 0x1b (Black HP Out): present = No [julas@snowball2 ~]$ sudo python hda-jack-sense-test.py Pin 0x18 (Black Mic): present = No Pin 0x1a (Black Line In): present = Yes Pin 0x1b (Black HP Out): present = No [julas@snowball2 ~]$ sudo python hda-jack-sense-test.py Pin 0x18 (Black Mic): present = Yes Pin 0x1a (Black Line In): present = No Pin 0x1b (Black HP Out): present = No
Is Node 0x17 also the side jack of your p150hm ? pin cap support Detect and Trigger but Misc = NO_PRESENCE
Yes, it is between mic and line in jacks, third one from the front. The only difference is that there is red light coming out of it.
you can use hda-verb to set the pin default of 0x17 and use hda-jack-sense-test retest the side jack
Well, it kind of works:
- I was able to assign 0x01011013 to pin 0x17 using user_pin_configs
- it then shows up in hda-jack-sense-test.py, which detects if the jack
is connected $ sudo python hda-jack-sense-test.py [sudo] password for julas: Pin 0x17 (Black Line Out): present = Yes Pin 0x18 (Black Mic): present = No Pin 0x1a (Black Line In): present = No Pin 0x1b (Black HP Out): present = No
- for some reason this program started locking up after showing the
output, I am not sure if this is related.
Don't have any realtek codec, not sure why hda-jack-sense-test.py locked up when you use user_pin_configs
I then applied your patch on top of Fedora 3.1.1 kernel (crude patch attached). After reboot:
- hda-jack-sense-test.py was still working, without lockups this time
- alsamixer -c0 revealed a new "Front" slider, which was controlling the
volume on 0x17
- there was still no 8-channel mode (probably related to what you wrote
below)
- there were more options for auto mute (Disabled, Speaker Only, Line
Out+Speaker)
- here is the new alsa-info.sh:
http://www.alsa-project.org/db/?f=923b75ad3997dc8f5878852e327f9b999a196052
To add the missing pin default of side jack 0x17
ALC662_FIXUP_ASUS_MODE8,
- ALC892_FIXUP_CLEVO_4ST_8CH,
};
static const struct alc_fixup alc662_fixups[] = {
- [ALC892_FIXUP_CLEVO_4ST_8CH] = {
- .type = ALC_FIXUP_PINS,
- .v.pins = (const struct alc_pincfg[]) {
+/*
- need to be same location as the other jack
- may need to change the default association and sequence since
- Lower Default Association values would be higher in priority for resources
- such as processing nodes or Input and Output Converters.
- A value of 0000b is reserved and should not be used
+*/
{ 0x17, 0x01011013 }, /* Side */
{ }
},
},
SND_PCI_QUIRK(0x1558, 0x5102, "Clevo P150HM", ALC892_FIXUP_CLEVO_4ST_8CH),
SND_PCI_QUIRK(0x1558, 0x7100, "Clevo P170HM", ALC892_FIXUP_CLEVO_4ST_8CH),
SImilar case are those notebooks hda-emu/codecs/alc1200-msi-gx620 which has 1 hp(green), 1 line-in(blue), 1 ext-mic(pink) and 1 line out(grey) at same location (ext rear) for surround71 (and also 1 speakers, 1 int mic)
hda_codec: ALC1200: BIOS auto-probing. hda_codec: ALC1200: SKU not ready 0x598301f0 autoconfig: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:line speaker_outs=1 (0x1b/0x0/0x0/0x0/0x0) hp_outs=1 (0x14/0x0/0x0/0x0/0x0) mono: mono_out=0x0 dig-out=0x1e/0x0 inputs: Mic=0x18 Internal Mic=0x19 Line=0x1a
CTRL: add: Line-Out Jack:0 CTRL: add: Headphone Jack:0 CTRL: add: Mic Jack:0 CTRL: add: Line Jack:0
get 1
1 Channel Mode:0 ITEM: 0:2ch, 1:4ch, 2:6ch, VAL: [2ch]
After the pin fixup, your notebook is almost like alc1200 msi gx460 except speaker and hp are swapped, this mean that those volume controls and switches are similar to targa_mixer , targa_8ch_mixer of model="targa-8ch-dig"
This mean that when switch to 6/8 channel mode, it will conflict with automic detection since the pin cap alc892 's mic jack does not support impedance sense and the driver does not know the plug is mic or speaker by measuring the impedance
The driver have to disable automic detection when user switch "channel mode" to 6ch/8ch as the user should still able to use the internal mic when the external mic jack is retasked as output
The are some difference between p170hm and your p150hm if p170hm has 5.1 speakers which still can have auto mic detection enabled.
you can add the following code in alc_auto_ch_mode_put() for debugging and need to switch "auto mute mode" to "speaker" for 8 channels
if (spec->need_dac_fix && !spec->const_channel_count) spec->multiout.num_dacs = spec->multiout.max_channels / 2;
+ printk(KERN_INFO "ch = %d\n",ch); + printk(KERN_INFO "max channel %d\n",spec->multiout.max_channels); + for (i=0; i<spec->autocfg.hp_outs; i++) + printk(KERN_INFO "hp dac(%d) %x pin %x\n", i, spec->multiout.hp_out_nid[i], spec->autocfg.hp_pins[i]); + for (i=0; i<spec->multiout.num_dacs; i++) + printk(KERN_INFO "private_dac(%d) %x\n", i, spec->private_dac_nids[i]); + for (i=0; i<spec->autocfg.line_outs; i++) + printk(KERN_INFO "line_out(%d) pin %x\n", i, spec->autocfg.line_out_pins[i]); + for (i=0; i<spec->multiout.num_dacs-1; i++) + printk(KERN_INFO "multi_io(%d) dac %x pin %x\n", i, spec->multi_io[i].dac, spec->multi_io[i].pin); + for (i=0; i<spec->autocfg.speaker_outs; i++) + printk(KERN_INFO "extra_out(%d) dac %x pin %x\n", i, spec->multiout.extra_out_nid[i], spec->autocfg.speaker_pins[i]); return 1
Try the following code which try to assign dac 02, 03, 04, and 05 to spec->private_dac front, surround, clfe and side.
static int alc_auto_fill_dac_nids(struct hda_codec *codec) { ... again: /* set num_dacs once to full for alc_auto_look_for_dac() */ spec->multiout.num_dacs = cfg->line_outs; spec->multiout.hp_out_nid[0] = 0; spec->multiout.extra_out_nid[0] = 0; memset(spec->private_dac_nids, 0, sizeof(spec->private_dac_nids)); spec->multiout.dac_nids = spec->private_dac_nids;
+ if (cfg->hp_outs == 1 && cfg->line_outs == 1 && + cfg->num_inputs >= 3 && cfg->speaker_outs >= 1) { +/* assign 0x02 as Front DAC by using speaker or hp pins*/ + spec->private_dac_nids[0] = alc_auto_look_for_dac(codec, cfg->speaker_pins[0]); +/* hp , mic and line-in at the same location + use alc_auto_fill_multi_ios() to assign surround and clfe dacs +*/ + defcfg = snd_hda_codec_get_pincfg(codec, cfg->hp_pins[0]); + location = get_defcfg_location(defcfg); + spec->multiout.num_dacs = 1; + num_pins = alc_auto_fill_multi_ios(codec, location, 1); + if (num_pins > 0) { + spec->multi_ios = num_pins; + spec->ext_channel_count = 2; + spec->multiout.num_dacs = num_pins + 1; + } +/* an ugly hack to add side as multi io even side does not support input + set pin ctl to PIN_OUT to set multi_io[2].ctl_in to PIN_OUT */ + if (location == get_defcfg_location(snd_hda_codec_get_pincfg(codec, cfg->line_out_pins[0]))) { + spec->private_dac_nids[3] = alc_auto_look_for_dac(codec, cfg->line_out_pins[0]); + spec->multi_io[2].dac = spec->private_dac_nids[3]; + spec->multi_io[2].pin = cfg->line_out_pins[0]; + snd_hda_codec_write(codec, cfg->line_out_pins[0], 0, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_OUT); + spec->multi_ios++; + spec->multiout.num_dacs++; + } + return 0; + }