On 2019-09-03 20:08, Jernej Škrabec wrote:
Hi!
Dne torek, 03. september 2019 ob 20:00:33 CEST je Neil Armstrong napisal(a):
Hi,
Le 03/09/2019 à 11:53, Neil Armstrong a écrit :
Hi,
On 03/09/2019 07:51, Cheng-Yi Chiang wrote:
From: Yakir Yang ykk@rock-chips.com
When transmitting IEC60985 linear PCM audio, we configure the Audio Sample Channel Status information of all the channel status bits in the IEC60958 frame. Refer to 60958-3 page 10 for frequency, original frequency, and wordlength setting.
This fix the issue that audio does not come out on some monitors (e.g. LG 22CV241)
Signed-off-by: Yakir Yang ykk@rock-chips.com Signed-off-by: Cheng-Yi Chiang cychiang@chromium.org
drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 59 +++++++++++++++++++++++ drivers/gpu/drm/bridge/synopsys/dw-hdmi.h | 20 ++++++++ 2 files changed, 79 insertions(+)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c index bd65d0479683..34d46e25d610 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c @@ -582,6 +582,63 @@ static unsigned int hdmi_compute_n(unsigned int freq, unsigned long pixel_clk)>> return n;
}
+static void hdmi_set_schnl(struct dw_hdmi *hdmi) +{
- u8 aud_schnl_samplerate;
- u8 aud_schnl_8;
- /* These registers are on RK3288 using version 2.0a. */
- if (hdmi->version != 0x200a)
return;Are these limited to the 2.0a version *in* RK3288, or 2.0a version on all SoCs ?
After investigations, Amlogic sets these registers on their 2.0a version aswell, and Jernej (added in Cc) reported me Allwinner sets them on their < 2.0a and > 2.0a IPs versions.
Can you check on the Rockchip IP versions in RK3399 ?
For reference, the HDMI 1.4a IP version allwinner setups is: https://github.com/Allwinner-Homlet/H3-BSP4.4-linux/blob/master/drivers/vide o/fbdev/sunxi/disp2/hdmi/hdmi_bsp_sun8iw7.c#L531-L539 (registers a "scrambled" but a custom bit can reset to the original mapping, 0x1066 ... 0x106f)
For easier reading, here is similar, but annotated version: http://ix.io/1Ub6 Check function bsp_hdmi_audio().
Unless there is a special reason, you can just remove that check.
Agree, this check should not be needed, AUDSCHNLS7 used to be configured in my old multi-channel patches that have seen lot of testing on Amlogic, Allwinner and Rockchip SoCs.
Best regards, Jernej
Neil
- switch (hdmi->sample_rate) {
- case 32000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_32K;break;- case 44100:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_44K1;break;- case 48000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_48K;break;- case 88200:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_88K2;break;- case 96000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_96K;break;- case 176400:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_176K4;break;- case 192000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_192K;break;- case 768000:
aud_schnl_samplerate = HDMI_FC_AUDSCHNLS7_SMPRATE_768K;break;- default:
dev_warn(hdmi->dev, "Unsupported audio sample rate (%u)\n",hdmi->sample_rate);return;- }
- /* set channel status register */
- hdmi_modb(hdmi, aud_schnl_samplerate, HDMI_FC_AUDSCHNLS7_SMPRATE_MASK,
HDMI_FC_AUDSCHNLS7);- /*
* Set original frequency to be the same as frequency.* Use one-complement value as stated in IEC60958-3 page 13.*/- aud_schnl_8 = (~aud_schnl_samplerate) <<
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_OFFSET;- /* This means word length is 16 bit. Refer to IEC60958-3 page 12. */
- aud_schnl_8 |= 2 << HDMI_FC_AUDSCHNLS8_WORDLEGNTH_OFFSET;
This looks wrong, user can use 16 and 24 bit wide audio streams.
- hdmi_writeb(hdmi, aud_schnl_8, HDMI_FC_AUDSCHNLS8);
+}
static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,
unsigned long pixel_clk, unsigned int sample_rate)
{
@@ -620,6 +677,8 @@ static void hdmi_set_clk_regenerator(struct dw_hdmi *hdmi,>> hdmi->audio_cts = cts; hdmi_set_cts_n(hdmi, cts, hdmi->audio_enable ? n : 0); spin_unlock_irq(&hdmi->audio_lock);
- hdmi_set_schnl(hdmi);
I will suggest this function is called from or merged with dw_hdmi_set_sample_rate(). Similar to how AUDSCONF and AUDICONF0 is configured from dw_hdmi_set_channel_count().
Regards, Jonas
}
static void hdmi_init_clk_regenerator(struct dw_hdmi *hdmi)
diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h index 6988f12d89d9..619ebc1c8354 100644 --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.h @@ -158,6 +158,17 @@
#define HDMI_FC_SPDDEVICEINF 0x1062 #define HDMI_FC_AUDSCONF 0x1063 #define HDMI_FC_AUDSSTAT 0x1064
+#define HDMI_FC_AUDSV 0x1065 +#define HDMI_FC_AUDSU 0x1066 +#define HDMI_FC_AUDSCHNLS0 0x1067 +#define HDMI_FC_AUDSCHNLS1 0x1068 +#define HDMI_FC_AUDSCHNLS2 0x1069 +#define HDMI_FC_AUDSCHNLS3 0x106a +#define HDMI_FC_AUDSCHNLS4 0x106b +#define HDMI_FC_AUDSCHNLS5 0x106c +#define HDMI_FC_AUDSCHNLS6 0x106d +#define HDMI_FC_AUDSCHNLS7 0x106e +#define HDMI_FC_AUDSCHNLS8 0x106f
#define HDMI_FC_DATACH0FILL 0x1070 #define HDMI_FC_DATACH1FILL 0x1071 #define HDMI_FC_DATACH2FILL 0x1072
@@ -706,6 +717,15 @@ enum {
/* HDMI_FC_AUDSCHNLS7 field values */
HDMI_FC_AUDSCHNLS7_ACCURACY_OFFSET = 4, HDMI_FC_AUDSCHNLS7_ACCURACY_MASK = 0x30,
- HDMI_FC_AUDSCHNLS7_SMPRATE_MASK = 0x0f,
- HDMI_FC_AUDSCHNLS7_SMPRATE_192K = 0xe,
- HDMI_FC_AUDSCHNLS7_SMPRATE_176K4 = 0xc,
- HDMI_FC_AUDSCHNLS7_SMPRATE_96K = 0xa,
- HDMI_FC_AUDSCHNLS7_SMPRATE_768K = 0x9,
- HDMI_FC_AUDSCHNLS7_SMPRATE_88K2 = 0x8,
- HDMI_FC_AUDSCHNLS7_SMPRATE_32K = 0x3,
- HDMI_FC_AUDSCHNLS7_SMPRATE_48K = 0x2,
- HDMI_FC_AUDSCHNLS7_SMPRATE_44K1 = 0x0,
/* HDMI_FC_AUDSCHNLS8 field values */
HDMI_FC_AUDSCHNLS8_ORIGSAMPFREQ_MASK = 0xf0,