From: Ben Zhang benzh@chromium.org
Before a hotword is detected, GPIO1 pin is configured as IRQ output so that jack detect works. When a hotword is detected, the DSP firmware configures the GPIO1 pin as GPIO1 and drives a 1. rt5677_irq() is called after a rising edge on the GPIO1 pin, due to either jack detect event or hotword event, or both. All possible events are checked and handled in rt5677_irq() where GPIO1 pin is configured back to IRQ output if a hotword is detected.
Signed-off-by: Ben Zhang benzh@chromium.org Signed-off-by: Curtis Malainey cujomalainey@chromium.org --- sound/soc/codecs/rt5677.c | 64 +++++++++++++++++++++++++++++---------- 1 file changed, 48 insertions(+), 16 deletions(-)
diff --git a/sound/soc/codecs/rt5677.c b/sound/soc/codecs/rt5677.c index 13f21bf4e04e..48955b22262f 100644 --- a/sound/soc/codecs/rt5677.c +++ b/sound/soc/codecs/rt5677.c @@ -312,6 +312,8 @@ static bool rt5677_volatile_register(struct device *dev, unsigned int reg) case RT5677_IRQ_CTRL1: case RT5677_IRQ_CTRL2: case RT5677_GPIO_ST: + case RT5677_GPIO_CTRL1: /* Modified by DSP firmware */ + case RT5677_GPIO_CTRL2: /* Modified by DSP firmware */ case RT5677_DSP_INB1_SRC_CTRL4: case RT5677_DSP_INB2_SRC_CTRL4: case RT5677_DSP_INB3_SRC_CTRL4: @@ -746,8 +748,11 @@ static unsigned int rt5677_set_vad_source(struct rt5677_priv *rt5677) RT5677_VAD_BUF_OW | RT5677_VAD_FG2ENC | RT5677_VAD_ADPCM_BYPASS | 1 << RT5677_VAD_MIN_DUR_SFT);
- /* IRQ Source of VAD Jack Detection = enable */ - regmap_write(rt5677->regmap, RT5677_IRQ_CTRL2, 0x4000); + /* VAD/SAD is not routed to the IRQ output (i.e. MX-BE[14] = 0), but it + * is routed to DSP_IRQ_0, so DSP firmware may use it to sleep and save + * power. See ALC5677 datasheet section 9.17 "GPIO, Interrupt and Jack + * Detection" for more info. + */
/* Private register, no doc */ regmap_update_bits(rt5677->regmap, RT5677_PR_BASE + RT5677_BIAS_CUR4, @@ -886,15 +891,15 @@ static void rt5677_dsp_work(struct work_struct *work) if (enable && !activity) { activity = true;
- /* Set GPIO1 as an output pin driving a 0. Firmware will - * raise GPIO1 upon hotword detect. + /* Before a hotword is detected, GPIO1 pin is configured as IRQ + * output so that jack detect works. When a hotword is detected, + * the DSP firmware configures the GPIO1 pin as GPIO1 and + * drives a 1. rt5677_irq() is called after a rising edge on + * the GPIO1 pin, due to either jack detect event or hotword + * event, or both. All possible events are checked and handled + * in rt5677_irq() where GPIO1 pin is configured back to IRQ + * output if a hotword is detected. */ - regmap_update_bits(rt5677->regmap, RT5677_GPIO_CTRL2, - RT5677_GPIO1_DIR_MASK | RT5677_GPIO1_OUT_MASK | - RT5677_GPIO1_P_MASK, RT5677_GPIO1_DIR_OUT | - RT5677_GPIO1_OUT_LO | RT5677_GPIO1_P_NOR); - regmap_update_bits(rt5677->regmap, RT5677_GPIO_CTRL1, - RT5677_GPIO1_PIN_MASK, RT5677_GPIO1_PIN_GPIO1);
rt5677_set_vad_source(rt5677); rt5677_set_dsp_mode(rt5677, true); @@ -915,6 +920,8 @@ static void rt5677_dsp_work(struct work_struct *work) } else if (!enable && activity) { activity = false;
+ /* Don't turn off the DSP while handling irqs */ + mutex_lock(&rt5677->irq_lock); /* Set DSP CPU to Stop */ regmap_update_bits(rt5677->regmap, RT5677_PWR_DSP1, RT5677_PWR_DSP_CPU, RT5677_PWR_DSP_CPU); @@ -923,13 +930,12 @@ static void rt5677_dsp_work(struct work_struct *work)
/* Disable and clear VAD interrupt */ regmap_write(rt5677->regmap, RT5677_VAD_CTRL1, 0x2184); - regmap_update_bits(rt5677->regmap, RT5677_IRQ_CTRL2, - 0xF000, 0x0000);
/* Set GPIO1 pin back to be IRQ output for jack detect */ regmap_update_bits(rt5677->regmap, RT5677_GPIO_CTRL1, RT5677_GPIO1_PIN_MASK, RT5677_GPIO1_PIN_IRQ);
+ mutex_unlock(&rt5677->irq_lock); } }
@@ -5237,6 +5243,28 @@ static const struct rt5677_irq_desc rt5677_irq_descs[] = { }, };
+bool rt5677_check_hotword(struct rt5677_priv *rt5677) +{ + int reg_gpio; + + if (!rt5677->is_dsp_mode) + return false; + + if (regmap_read(rt5677->regmap, RT5677_GPIO_CTRL1, ®_gpio)) + return false; + + /* Firmware sets GPIO1 pin to be GPIO1 after hotword is detected */ + if ((reg_gpio & RT5677_GPIO1_PIN_MASK) == RT5677_GPIO1_PIN_IRQ) + return false; + + /* Set GPIO1 pin back to be IRQ output for jack detect */ + regmap_update_bits(rt5677->regmap, RT5677_GPIO_CTRL1, + RT5677_GPIO1_PIN_MASK, RT5677_GPIO1_PIN_IRQ); + + rt5677_spi_hotword_detected(); + return true; +} + static irqreturn_t rt5677_irq(int unused, void *data) { struct rt5677_priv *rt5677 = data; @@ -5245,9 +5273,6 @@ static irqreturn_t rt5677_irq(int unused, void *data)
mutex_lock(&rt5677->irq_lock);
- if (rt5677->dsp_vad_en) - rt5677_spi_hotword_detected(); - /* * Loop to handle interrupts until the last i2c read shows no pending * irqs. The interrupt line is shared by multiple interrupt sources. @@ -5285,7 +5310,13 @@ static irqreturn_t rt5677_irq(int unused, void *data) reg_irq ^= rt5677_irq_descs[i].polarity_mask; } } - if (!irq_fired) + + /* Exit the loop only when we know for sure that GPIO1 pin + * was low at some point since irq_lock was acquired. Any event + * after that point creates a rising edge that triggers another + * call to rt5677_irq(). + */ + if (!irq_fired && !rt5677_check_hotword(rt5677)) goto exit;
ret = regmap_write(rt5677->regmap, RT5677_IRQ_CTRL1, reg_irq); @@ -5296,6 +5327,7 @@ static irqreturn_t rt5677_irq(int unused, void *data) } } exit: + WARN_ON_ONCE(loop == 20); mutex_unlock(&rt5677->irq_lock); if (irq_fired) return IRQ_HANDLED;