Re: [alsa-devel] [PATCH v2] ASoC: atmel_ssc_dai: Allow more rates

Hi Peter,

On 02/04/2015 07:52 PM, Peter Rosin wrote:

From: Peter Rosin peda@axentia.se

When the SSC acts as BCK master, use a ratnum rule to limit the rate instead of only doing the standard rates. When the SSC acts as BCK slave, allow any BCK frequency up to within 500ppm of the SSC master clock, possibly divided by 2, 3 or 6.

Put a cap at 384kHz. Who's /ever/ going to need more than that?

The divider of 2, 3 or 6 is selected based on the Serial Clock Ratio Considerations section from the SSC documentation:

 The Transmitter and the Receiver can be programmed to operate
 with the clock signals provided on either the TK or RK pins.
 This allows the SSC to support many slave-mode data transfers.
 In this case, the maximum clock speed allowed on the RK pin is:
 - Peripheral clock divided by 2 if Receiver Frame Synchro is input
 - Peripheral clock divided by 3 if Receiver Frame Synchro is output
 In addition, the maximum clock speed allowed on the TK pin is:
 - Peripheral clock divided by 6 if Transmit Frame Synchro is input
 - Peripheral clock divided by 2 if Transmit Frame Synchro is output

Signed-off-by: Peter Rosin peda@axentia.se

sound/soc/atmel/atmel_ssc_dai.c | 113 +++++++++++++++++++++++++++++++++++++-- sound/soc/atmel/atmel_ssc_dai.h | 1 + 2 files changed, 110 insertions(+), 4 deletions(-)

Changes since v1:

• I have checked all Atmel datasheets I could get my hands on (and that seemed relevant), and in every instance where they have described the SSC, the description have the exact rate limitations on the RK and TK pin that I have implemented here.

• Improved the comments.

• Rebased on top of the latest patches from Bo Chen.

One thing remains a bit unclear, and that is the 500ppm deduction. Is that really warranted? The number was just pulled out of my hat...

Cheers, Peter

diff --git a/sound/soc/atmel/atmel_ssc_dai.c b/sound/soc/atmel/atmel_ssc_dai.c index 379ac2a6ab16..767f65bab25d 100644 --- a/sound/soc/atmel/atmel_ssc_dai.c +++ b/sound/soc/atmel/atmel_ssc_dai.c @@ -187,6 +187,96 @@ static irqreturn_t atmel_ssc_interrupt(int irq, void *dev_id) return IRQ_HANDLED; }

+/*

• • When the bit clock is input, limit the maximum rate according to the
• • Serial Clock Ratio Considerations section from the SSC documentation:
• • The Transmitter and the Receiver can be programmed to operate
• • with the clock signals provided on either the TK or RK pins.
• • This allows the SSC to support many slave-mode data transfers.
• • In this case, the maximum clock speed allowed on the RK pin is:
• • • Peripheral clock divided by 2 if Receiver Frame Synchro is input
• • • Peripheral clock divided by 3 if Receiver Frame Synchro is output
• • In addition, the maximum clock speed allowed on the TK pin is:
• • • Peripheral clock divided by 6 if Transmit Frame Synchro is input
• • • Peripheral clock divided by 2 if Transmit Frame Synchro is output
• • When the bit clock is output, limit the rate according to the
• • SSC divider restrictions.
• */

+static int atmel_ssc_hw_rule_rate(struct snd_pcm_hw_params *params,

• 		  struct snd_pcm_hw_rule *rule)
  

+{

• struct atmel_ssc_info *ssc_p = rule->private;
• struct ssc_device *ssc = ssc_p->ssc;
• struct snd_interval *i = hw_param_interval(params, rule->var);
• struct snd_interval t;
• struct snd_ratnum r = {

• .den_min = 1,
  

• .den_max = 4095,
  

• .den_step = 1,
  

• };
• unsigned int num = 0, den = 0;
• int frame_size;
• int mck_div = 2;
• int ret;
• frame_size = snd_soc_params_to_frame_size(params);
• if (frame_size < 0)

• return frame_size;
  

• switch (ssc_p->daifmt & SND_SOC_DAIFMT_MASTER_MASK) {
• case SND_SOC_DAIFMT_CBM_CFS:

• if ((ssc_p->dir_mask & SSC_DIR_MASK_CAPTURE)
  

•     && ssc->clk_from_rk_pin)
  

• 	/* Receiver Frame Synchro (i.e. capture)
  

• 	 * is output (format is _CFS) and the RK pin
  

• 	 * is used for input (format is _CBM_).
  

• 	 */
  

• 	mck_div = 3;
  

• break;
  

• case SND_SOC_DAIFMT_CBM_CFM:

• if ((ssc_p->dir_mask & SSC_DIR_MASK_PLAYBACK)
  

•     && !ssc->clk_from_rk_pin)
  

• 	/* Transmit Frame Synchro (i.e. playback)
  

• 	 * is input (format is _CFM) and the TK pin
  

• 	 * is used for input (format _CBM_ but not
  

• 	 * using the RK pin).
  

• 	 */
  

• 	mck_div = 6;
  

• break;
  

• }
• switch (ssc_p->daifmt & SND_SOC_DAIFMT_MASTER_MASK) {
• case SND_SOC_DAIFMT_CBS_CFS:

• r.num = ssc_p->mck_rate / mck_div / frame_size;
  

• ret = snd_interval_ratnum(i, 1, &r, &num, &den);
  

• if (ret >= 0 && den && rule->var == SNDRV_PCM_HW_PARAM_RATE) {
  

• 	params->rate_num = num;
  

• 	params->rate_den = den;
  

• }
  

• break;
  

• case SND_SOC_DAIFMT_CBM_CFS:
• case SND_SOC_DAIFMT_CBM_CFM:

• t.min = 8000;
  

• t.max = ssc_p->mck_rate / mck_div / frame_size;
  

• /* Take away 500ppm, just to be on the safe side. */
  

• t.max -= t.max / 2000;
  

• t.openmin = t.openmax = 0;
  

• t.integer = 0;
  

• ret = snd_interval_refine(i, &t);
  

• break;
  

• default:

• ret = -EINVAL;
  

• break;
  

• }
• return ret;

+}

/*-------------------------------------------------------------------------*\

• DAI functions

@@ -200,6 +290,7 @@ static int atmel_ssc_startup(struct snd_pcm_substream *substream, struct atmel_ssc_info *ssc_p = &ssc_info[dai->id]; struct atmel_pcm_dma_params *dma_params; int dir, dir_mask;

• int ret;

  pr_debug("atmel_ssc_startup: SSC_SR=0x%u\n", ssc_readl(ssc_p->ssc->regs, SR));

@@ -207,6 +298,7 @@ static int atmel_ssc_startup(struct snd_pcm_substream *substream, /* Enable PMC peripheral clock for this SSC */ pr_debug("atmel_ssc_dai: Starting clock\n"); clk_enable(ssc_p->ssc->clk);

• ssc_p->mck_rate = clk_get_rate(ssc_p->ssc->clk) * 2;

Why the mck_rate is calculated in this form?

/* Reset the SSC to keep it at a clean status */ ssc_writel(ssc_p->ssc->regs, CR, SSC_BIT(CR_SWRST)); @@ -219,6 +311,17 @@ static int atmel_ssc_startup(struct snd_pcm_substream *substream, dir_mask = SSC_DIR_MASK_CAPTURE; }

• ret = snd_pcm_hw_rule_add(substream->runtime, 0,

• 		  SNDRV_PCM_HW_PARAM_RATE,
  

• 		  atmel_ssc_hw_rule_rate,
  

• 		  ssc_p,
  

• 		  SNDRV_PCM_HW_PARAM_FRAME_BITS,
  

• 		  SNDRV_PCM_HW_PARAM_CHANNELS, -1);
  

• if (ret < 0) {

• dev_err(dai->dev, "Failed to specify rate rule: %d\n", ret);
  

• return ret;
  

• }
• dma_params = &ssc_dma_params[dai->id][dir]; dma_params->ssc = ssc_p->ssc; dma_params->substream = substream;

@@ -783,8 +886,6 @@ static int atmel_ssc_resume(struct snd_soc_dai *cpu_dai) # define atmel_ssc_resume NULL #endif /* CONFIG_PM */

-#define ATMEL_SSC_RATES (SNDRV_PCM_RATE_8000_96000)

• #define ATMEL_SSC_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE |\ SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE)

@@ -804,12 +905,16 @@ static struct snd_soc_dai_driver atmel_ssc_dai = { .playback = { .channels_min = 1, .channels_max = 2,

• 	.rates = ATMEL_SSC_RATES,
  

• 	.rates = SNDRV_PCM_RATE_CONTINUOUS,
  

• 	.rate_min = 8000,
  

• 	.rate_max = 384000,
  

Why this need to be changed? Do you mean in your application, the rates will exceed 96000?

	.formats = ATMEL_SSC_FORMATS,},
.capture = {
	.channels_min = 1,
	.channels_max = 2,

• 	.rates = ATMEL_SSC_RATES,
  

• 	.rates = SNDRV_PCM_RATE_CONTINUOUS,
  

• 	.rate_min = 8000,
  

• 	.rate_max = 384000,
  

Ditto.

	.formats = ATMEL_SSC_FORMATS,},
.ops = &atmel_ssc_dai_ops,

}; diff --git a/sound/soc/atmel/atmel_ssc_dai.h b/sound/soc/atmel/atmel_ssc_dai.h index b1f08d511495..80b153857a88 100644 --- a/sound/soc/atmel/atmel_ssc_dai.h +++ b/sound/soc/atmel/atmel_ssc_dai.h @@ -115,6 +115,7 @@ struct atmel_ssc_info { unsigned short rcmr_period; struct atmel_pcm_dma_params *dma_params[2]; struct atmel_ssc_state ssc_state;

• unsigned long mck_rate; };

  int atmel_ssc_set_audio(int ssc_id);

Best Regards, Bo Shen