Add a DT schema for describing nau8325 audio amplifiers. The key features are as follows: - Low SPK_VDD Quiescent Current - Gain Setting with 2-wire interface - Powerful Stereo Class-D Amplifier - Low Output Noise - Low Current Shutdown Mode - Click-and Pop Suppression
More resources : https://www.nuvoton.com/products/smart-home-audio/audio-amplifiers/class-d-s...
Signed-off-by: Seven Lee wtli@nuvoton.com --- .../bindings/sound/nuvoton,nau8325.yaml | 80 +++++++++++++++++++ 1 file changed, 80 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/nuvoton,nau8325.yaml
diff --git a/Documentation/devicetree/bindings/sound/nuvoton,nau8325.yaml b/Documentation/devicetree/bindings/sound/nuvoton,nau8325.yaml new file mode 100644 index 000000000000..979be0d336da --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nuvoton,nau8325.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/nuvoton,nau8325.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NAU8325 audio Amplifier + +maintainers: + - Seven Lee WTLI@nuvoton.com + +allOf: + - $ref: dai-common.yaml# + +properties: + compatible: + const: nuvoton,nau8325 + + reg: + maxItems: 1 + + nuvoton,vref-impedance-ohms: + description: + The vref impedance to be used in ohms. Middle of voltage enables + Tie-Off selection options. Due to the high impedance of the VREF + pin, it is important to use a low-leakage capacitor. + + enum: [0, 25000, 125000, 2500] + + nuvoton,dac-vref-microvolt: + description: + The DAC vref to be used in voltage. DAC reference voltage setting. Can + be used for minor tuning of the output level. Since the VDDA is range + between 1.62 to 1.98 voltage, the typical value for design is 1.8V. After + the minor tuning, the final microvolt are as the below. + + enum: [1800000, 2700000, 2880000, 3060000] + + nuvoton,alc-enable: + description: + Enable digital automatic level control (ALC) function. + type: boolean + + nuvoton,clock-detection-disable: + description: + When clock detection is enabled, it will detect whether MCLK + and FS are within the range. MCLK range is from 2.048MHz to 24.576MHz. + FS range is from 8kHz to 96kHz. And also needs to detect the ratio + MCLK_SRC/LRCK of 256, 400 or 500, and needs to detect the BCLK + to make sure data is present. There needs to be at least 8 BCLK + cycles per Frame Sync. + type: boolean + + nuvoton,clock-det-data: + description: + Request clock detection to require 2048 non-zero samples before enabling + the audio paths. If set then non-zero samples is required, otherwise it + doesn't matter. + type: boolean + +required: + - compatible + - reg + +unevaluatedProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + codec@21 { + compatible = "nuvoton,nau8325"; + reg = <0x21>; + nuvoton,vref-impedance-ohms = <125000>; + nuvoton,dac-vref-microvolt = <2880000>; + nuvoton,alc-enable; + nuvoton,clock-det-data; + }; + };