As mentioned slightly out of patch context in the code, there is no reset routine for the chip. On boards where the chip is supplied by a fixed regulator, it might not even be resetted during (e.g. watchdog) reboot and can be in any state.
If the device is probed with VAG enabled, the driver's probe routine will generate a loud pop sound when ANA_POWER is being programmed. Avoid this by properly disabling just the VAG bit and waiting the required power down time.
Signed-off-by: Sebastian Reichel sebastian.reichel@collabora.com --- sound/soc/codecs/sgtl5000.c | 34 ++++++++++++++++++++++++++++++++++ sound/soc/codecs/sgtl5000.h | 1 + 2 files changed, 35 insertions(+)
diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c index d5130193b4a2..e8a8bf7b4ffe 100644 --- a/sound/soc/codecs/sgtl5000.c +++ b/sound/soc/codecs/sgtl5000.c @@ -1653,6 +1653,40 @@ static int sgtl5000_i2c_probe(struct i2c_client *client, dev_err(&client->dev, "Error %d initializing CHIP_CLK_CTRL\n", ret);
+ /* Mute everything to avoid pop from the following power-up */ + ret = regmap_write(sgtl5000->regmap, SGTL5000_CHIP_ANA_CTRL, + SGTL5000_CHIP_ANA_CTRL_DEFAULT); + if (ret) { + dev_err(&client->dev, + "Error %d muting outputs via CHIP_ANA_CTRL\n", ret); + goto disable_clk; + } + + /* + * If VAG is powered-on (e.g. from previous boot), it would be disabled + * by the write to ANA_POWER in later steps of the probe code. This + * may create a loud pop even with all outputs muted. The proper way + * to circumvent this is disabling the bit first and waiting the proper + * cool-down time. + */ + ret = regmap_read(sgtl5000->regmap, SGTL5000_CHIP_ANA_POWER, &value); + if (ret) { + dev_err(&client->dev, "Failed to read ANA_POWER: %d\n", ret); + goto disable_clk; + } + if (value & SGTL5000_VAG_POWERUP) { + ret = regmap_update_bits(sgtl5000->regmap, + SGTL5000_CHIP_ANA_POWER, + SGTL5000_VAG_POWERUP, + 0); + if (ret) { + dev_err(&client->dev, "Error %d disabling VAG\n", ret); + goto disable_clk; + } + + msleep(SGTL5000_VAG_POWERDOWN_DELAY); + } + /* Follow section 2.2.1.1 of AN3663 */ ana_pwr = SGTL5000_ANA_POWER_DEFAULT; if (sgtl5000->num_supplies <= VDDD) { diff --git a/sound/soc/codecs/sgtl5000.h b/sound/soc/codecs/sgtl5000.h index a4bf4bca95bf..56ec5863f250 100644 --- a/sound/soc/codecs/sgtl5000.h +++ b/sound/soc/codecs/sgtl5000.h @@ -233,6 +233,7 @@ /* * SGTL5000_CHIP_ANA_CTRL */ +#define SGTL5000_CHIP_ANA_CTRL_DEFAULT 0x0133 #define SGTL5000_LINE_OUT_MUTE 0x0100 #define SGTL5000_HP_SEL_MASK 0x0040 #define SGTL5000_HP_SEL_SHIFT 6