March 2024 - Alsa-devel - mailman.alsa-project.org

hda: how to implement component master_unbind?
by Kai Vehmanen 20 Dec '24

20 Dec '24

Hi Takashi et al, I've been having multiple discussions with our i915 team w.r.t. audio driver behaviour when the aggregate component is unbound, triggered by i915 unbind. This came up again in the recent regression with devres allocations and I now dug into the topic again. In short, I'm puzzled how to really implement this. ALSA (or ASoC) don't really have support for individual components of a card disappearing in a hotplug fashion. At card level, we do have such support (USB, firewire and recent work for PCI hotplug). But not individual components of a card getting unplugged. In current code we have this: static void hdac_component_master_unbind(struct device *dev) { » struct drm_audio_component *acomp = hdac_get_acomp(dev); » if (acomp->audio_ops && acomp->audio_ops->master_unbind) » » acomp->audio_ops->master_unbind(dev, acomp); » module_put(acomp->ops->owner); » component_unbind_all(dev, acomp); » WARN_ON(acomp->ops || acomp->dev); } ... when e.g. i915 driver is unbound (but could be any driver using the component framework, not jus Intel hw), i915 calls component_del() and HDA gets call to the above. After this, acomp ops are null are audio no longer has ability to talk to i915 driver (which makes sense given it's unbound). If audio was runtime suspended, this kind of works (but relies on some good luck). Upon HDA controller resume, we note acomp ops are NULL and HDMI/DP operations (like snd_hdac_display_power()) silently become no-ops. PCM streaming will go to /dev/null, but this is ok'ish since no monitor can be connected anyways. If audio was active, we start to get warnings or worse. Audio expects hw display codec to be powered and programmed, but suddenly it mey lose state. If the audio controller is actually part of the display hardware (e.g. discrete GPUs), then controller registers can stop functioning (they should be still available, but given the main diplay driver is unbound, odds of suprising behaviour are high). So this is less than ideal. I've been looking at options: 1) prevent/block the unbind if audio device is busy The component framework does not allow individual components to return -EBUSY, so there's no way to let others know that unbind is not possible now. This would force anyone testing DRM driver unbind to first unbind the audio driver and stop any active audio use-cases if needed. 2) unbind the ALSA card I've experimented doing a device_unregister() from the above callback, but this has not really worked (onion peeling exercise of new probelms). The code is shared by multiple controllers, so getting a handle to an snd_card object is not straighforward (drvdata is differnet for SOF and snd-hda-intel for instance). But with some new work, maybe we could call snd_card_disconnect() to detach the card and inform user-space. 3) continue as-is and try to fix bugs If audio is active, maybe we could force a acomp->put_power() to ensure a clean unregister of the display part. But this leaves a big chunk of issues especially with HDA controllers that require the display to be powered on, to function. .. Any ideas, and/or has there been prior work? It seems Takashi it's been mostly you who has been active working on the acomp integration recently. I also included Chris, Daniel and Jani who've had patches to hdac_component.c. Br, Kai

3 5

[PATCH] dt-bindings: sound:atmel-at91sam9g20ek: convert bindings to json-schema
by Balakrishnan Sambath 10 Dec '24

10 Dec '24

Convert atmel-at91sam9g20ek-wm8731-audio DT binding to yaml based json-schema.Change file name to match json-scheme naming. Signed-off-by: Balakrishnan Sambath <balakrishnan.s(a)microchip.com> --- .../bindings/sound/atmel,at91sam9g20ek-wm8731.yaml | 60 ++++++++++++++++++++++ .../sound/atmel-at91sam9g20ek-wm8731-audio.txt | 26 ---------- 2 files changed, 60 insertions(+), 26 deletions(-) diff --git a/Documentation/devicetree/bindings/sound/atmel,at91sam9g20ek-wm8731.yaml b/Documentation/devicetree/bindings/sound/atmel,at91sam9g20ek-wm8731.yaml new file mode 100644 index 000000000000..f6330707fe1b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel,at91sam9g20ek-wm8731.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/atmel,at91sam9g20ek-wm8731.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel at91sam9g20ek wm8731 audio complex + +maintainers: + - Balakrishnan Sambath <balakrishnan.s(a)microchip.com> + +properties: + compatible: + const: atmel,at91sam9g20ek-wm8731-audio + + atmel,model: + $ref: /schemas/types.yaml#/definitions/string + description: The user-visible name of this sound complex. + atmel,audio-routing: + $ref: /schemas/types.yaml#/definitions/non-unique-string-array + description: A list of the connections between audio components. + minItems: 2 + items: + enum: + # Board Connectors + - "Ext Spk" + - "Int MIC" + + # CODEC Pins + - LHPOUT + - MICIN + atmel,ssc-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: The phandle of the SSC controller + atmel,audio-codec: + $ref: /schemas/types.yaml#/definitions/phandle + description: The phandle of WM8731 audio codec + +required: + - compatible + - atmel,model + - atmel,audio-routing + - atmel,ssc-controller + - atmel,audio-codec + +additionalProperties: false + +examples: + - | + sound { + compatible = "atmel,at91sam9g20ek-wm8731-audio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_mck>; + atmel,model = "wm8731 @ AT91SAMG20EK"; + atmel,audio-routing = + "Ext Spk", "LHPOUT", + "Int MIC", "MICIN"; + atmel,ssc-controller = <&ssc0>; + atmel,audio-codec = <&wm8731>; + }; diff --git a/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt b/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt deleted file mode 100644 index 9c5a9947b64d..000000000000 --- a/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt +++ /dev/null @@ -1,26 +0,0 @@ -* Atmel at91sam9g20ek wm8731 audio complex - -Required properties: - - compatible: "atmel,at91sam9g20ek-wm8731-audio" - - atmel,model: The user-visible name of this sound complex. - - atmel,audio-routing: A list of the connections between audio components. - - atmel,ssc-controller: The phandle of the SSC controller - - atmel,audio-codec: The phandle of the WM8731 audio codec -Optional properties: - - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt - -Example: -sound { - compatible = "atmel,at91sam9g20ek-wm8731-audio"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pck0_as_mck>; - - atmel,model = "wm8731 @ AT91SAMG20EK"; - - atmel,audio-routing = - "Ext Spk", "LHPOUT", - "Int MIC", "MICIN"; - - atmel,ssc-controller = <&ssc0>; - atmel,audio-codec = <&wm8731>; -}; --- base-commit: 0dd3ee31125508cd67f7e7172247f05b7fd1753a change-id: 20240214-at91sam9g20ek-wm8731-yaml-404ddddbb91a Best regards, -- Balakrishnan Sambath <balakrishnan.s(a)microchip.com>

5 5

[PATCH v2 0/3] ASoC: mediatek:mt8186: fix both the speaker and hdmi
by Jiaxin Yu 06 Dec '24

06 Dec '24

The speaker and hdmi of mt8186 platform are shared the same port of I2S, when connect the external display, use build-in speakers to play audio, they both playback at the same time. So we want to manage the playback device through DAPM events. Change since v1: Support audio function for it6505 bridge to hdmi-codec Jiaxin Yu (3): ASoC: hdmi-codec: Add event handler for hdmi TX ASoC: mediatek: mt8186: correct the HDMI widgets drm/bridge: it6505: Add audio support drivers/gpu/drm/bridge/ite-it6505.c | 81 +++++++++++++++++-- include/sound/hdmi-codec.h | 6 ++ sound/soc/codecs/hdmi-codec.c | 37 ++++++++- .../mt8186/mt8186-mt6366-da7219-max98357.c | 2 +- .../mt8186/mt8186-mt6366-rt1019-rt5682s.c | 2 +- 5 files changed, 116 insertions(+), 12 deletions(-) -- 2.18.0

3 16

[alsa-devel] Error patching file pcm_native.c
by Delusion's Master 20 Nov '24

20 Nov '24

Hi, first of all I apologize in case you receive multiple copies of this message, but I forgot to specify a subject in the original mail. I have a problem compiling the latest alsa driver snapshots. Specifically, it's a problem when patching pcm_native.c: [..] copying file alsa-kernel/core/info.c patching file info.c copying file alsa-kernel/core/pcm.c patching file pcm.c Hunk #3 succeeded at 739 (offset 2 lines). Hunk #5 succeeded at 954 (offset 2 lines). Hunk #7 succeeded at 1045 (offset 2 lines). copying file alsa-kernel/core/pcm_native.c patching file pcm_native.c Hunk #4 succeeded at 1544 (offset -25 lines). Hunk #5 succeeded at 2827 (offset 12 lines). Hunk #6 succeeded at 2878 (offset 10 lines). Hunk #7 FAILED at 2906. Hunk #8 FAILED at 2922. Hunk #9 succeeded at 2915 (offset -23 lines). Hunk #10 succeeded at 3036 (offset 10 lines). Hunk #11 succeeded at 3027 (offset -23 lines). Hunk #12 succeeded at 3074 (offset 10 lines). Hunk #13 succeeded at 3098 (offset -23 lines). Hunk #14 succeeded at 3143 (offset 10 lines). Hunk #15 succeeded at 3124 (offset -23 lines). Hunk #16 succeeded at 3214 (offset 10 lines). Hunk #17 succeeded at 3208 (offset -23 lines). Hunk #18 succeeded at 3271 (offset 10 lines). Hunk #19 succeeded at 3304 (offset -23 lines). Hunk #20 succeeded at 3386 (offset 10 lines). Hunk #21 succeeded at 3411 (offset -23 lines). Hunk #22 succeeded at 3456 (offset 10 lines). Hunk #23 succeeded at 3450 (offset -23 lines). Hunk #24 succeeded at 3525 (offset 10 lines). Hunk #25 succeeded at 3644 (offset -23 lines). 2 out of 25 hunks FAILED -- saving rejects to file pcm_native.c.rej make[2]: *** [pcm_native.c] Error 1 It's some days I get this, but I waited to report this since I thought it could be a temporary problem. My OS is Fedora 11 x86_64. Previous snapshots didn't give me this problem, but I can't say which one broke the compilation, since I usually try updated snapshots only at kernel updates. I searched for this error and the only relevant report I could find is this one: http://mailman.alsa-project.org/pipermail/alsa-devel/2009-April/016420.html a report from last April. What could the problem be? Thanks _________________________________________________________________ Invite your mail contacts to join your friends list with Windows Live Spaces. It's easy! http://spaces.live.com/spacesapi.aspx?wx_action=create&wx_url=/friends.aspx…

3 10

ALSA 1.2.8 release
by Jaroslav Kysela 12 Nov '24

12 Nov '24

Hello all, new ALSA userspace packages were released. You may download them from the ALSA website http://www.alsa-project.org or directly: HTTP: https://www.alsa-project.org/files/pub FTP: ftp://ftp.alsa-project.org/pub Released packages: alsa-lib alsa-utils alsa-ucm-conf tinycompress Full list of changes: https://www.alsa-project.org/wiki/Changes_v1.2.7.2_v1.2.8 The fingerprint of the public signing key is: F04D F507 37AC 1A88 4C4B 3D71 8380 596D A6E5 9C91 Have fun, Jaroslav -- Jaroslav Kysela <perex(a)perex.cz> Linux Sound Maintainer; ALSA Project; Red Hat, Inc.

1 5

[alsa-devel] [RFC PATCH 00/10] Add support for DMA and audio codec of F1C100s
by Mesih Kilinc 23 Oct '24

23 Oct '24

This is RFC patchset for Allwinner suniv F1C100s to support DMA and audio codec. Allwinner F1C100s has a audio codec that has necessary digital and analog parts. It has r-l headphone output and microphone, line, r-l FM inputs. ADC can capture any inputs and also output channels via mux. Any input channels or DAC samples can feed output channels. Add support for this audio codec. F1C100s utilizes DMA channels to send and receive ADC-DAC samples. So DMA support needed. Patch 1~5 adds support for DMA. Suniv F1C100s has very similar DMA to sun4i. But there is some dissimilarities also. Suniv features a DMA reset bit in clock control unit. It has smaller number of DMA channels. Several registers has different addresses. It's max burst size is 4 instead of 8. Also DMA endpoint numbers are different. Patch 6 adds DMA max burst option to sun4i-codec. Patch 7~8 Add support for suniv F1C100s audio codec. Patch 9 adds audio codec to suniv-f1c100s.dtsi Patch 10 adds audio codec support to Lichee Pi Nano board. Thanks! Mesih Kilinc (10): dma-engine: sun4i: Add a quirk to support different chips dma-engine: sun4i: Add has_reset option to quirk dt-bindings: dmaengine: Add Allwinner suniv F1C100s DMA dma-engine: sun4i: Add support for Allwinner suniv F1C100s ARM: dts: suniv: f1c100s: Add support for DMA ASoC: sun4i-codec: Add DMA Max Burst field dt-bindigs: sound: Add Allwinner suniv F1C100s Audio Codec ASoC: sun4i-codec: Add support for Allwinner suniv F1C100s ARM: dts: suniv: f1c100s: Add support for Audio Codec ARM: dts: suniv: f1c100s: Activate Audio Codec for Lichee Pi Nano .../devicetree/bindings/dma/sun4i-dma.txt | 4 +- .../devicetree/bindings/sound/sun4i-codec.txt | 5 + arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts | 8 + arch/arm/boot/dts/suniv-f1c100s.dtsi | 25 ++ drivers/dma/Kconfig | 4 +- drivers/dma/sun4i-dma.c | 221 ++++++++++-- sound/soc/sunxi/sun4i-codec.c | 371 ++++++++++++++++++++- 7 files changed, 601 insertions(+), 37 deletions(-) -- 2.7.4

5 17

[RESEND PATCH v2] drm/bridge: dw-hdmi-i2s: set insert_pcuv bit if hardware supports it
by Geraldo Nascimento 14 Sep '24

14 Sep '24

Hi Mark, resending this as it failed to apply in my last submission. Added Neil Armstrong to Cc: as hopefully he will be able to better review this. Thanks, Geraldo Nascimento --- Starting with version 2.10a of Synopsys DesignWare HDMI controller the insert_pcuv bit was introduced. On RK3399pro SoM (Radxa Rock Pi N10), for example, if we neglect to set this bit and proceed to enable hdmi_sound and i2s2 on the device tree there will be extreme clipping of sound output, to the point that music sounds like white noise. Problem could also manifest as just mild cracking depending of HDMI audio implementation of sink. Setting insert_pcuv bit (bit 2 of aud_conf2 Audio Sample register) fixes this. Signed-off-by: Geraldo Nascimento <geraldogabriel(a)gmail.com> --- v1->v2: SoC->SoM on description, better commenting, minor style changes, conditional application of fix for L-PCM only --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio-20221017.c +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-i2s-audio-20221017.c @@ -42,6 +42,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev, void *data, struct dw_hdmi *hdmi = audio->hdmi; u8 conf0 = 0; u8 conf1 = 0; + u8 conf2 = 0; u8 inputclkfs = 0; /* it cares I2S only */ @@ -101,6 +102,28 @@ static int dw_hdmi_i2s_hw_params(struct device *dev, void *data, return -EINVAL; } + /* + * dw-hdmi introduced insert_pcuv bit in + * version 2.10a. + * + * This single bit (bit 2 of HDMI_AUD_CONF2) + * when set to 1 will enable the insertion of the PCUV + * (Parity, Channel Status, User bit and Validity) + * bits on the incoming audio stream. + * + * Support is limited to Linear PCM audio. If + * neglected, the lack of valid PCUV bits + * on L-PCM streams will cause anything from + * mild cracking to full blown extreme + * clipping depending on the HDMI audio + * implementation of the sink. + * + */ + + if (hdmi_read(audio, HDMI_DESIGN_ID) >= 0x21 && + !(hparms->iec.status[0] & IEC958_AES0_NONAUDIO)) + conf2 = HDMI_AUD_CONF2_INSERT_PCUV; + dw_hdmi_set_sample_rate(hdmi, hparms->sample_rate); dw_hdmi_set_channel_status(hdmi, hparms->iec.status); dw_hdmi_set_channel_count(hdmi, hparms->channels); @@ -109,6 +120,7 @@ static int dw_hdmi_i2s_hw_params(struct device *dev, void *data, hdmi_write(audio, inputclkfs, HDMI_AUD_INPUTCLKFS); hdmi_write(audio, conf0, HDMI_AUD_CONF0); hdmi_write(audio, conf1, HDMI_AUD_CONF1); + hdmi_write(audio, conf2, HDMI_AUD_CONF2); return 0; } --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi-20221017.h +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi-20221017.h @@ -931,6 +931,11 @@ enum { HDMI_AUD_CONF1_WIDTH_16 = 0x10, HDMI_AUD_CONF1_WIDTH_24 = 0x18, +/* AUD_CONF2 field values */ + HDMI_AUD_CONF2_HBR = 0x01, + HDMI_AUD_CONF2_NLPCM = 0x02, + HDMI_AUD_CONF2_INSERT_PCUV = 0x04, + /* AUD_CTS3 field values */ HDMI_AUD_CTS3_N_SHIFT_OFFSET = 5, HDMI_AUD_CTS3_N_SHIFT_MASK = 0xe0,

3 3

[RFC PATCH 00/16] soundwire/ASoC: speed-up downloads with BTP/BRA protocol
by Pierre-Louis Bossart 20 Aug '24

20 Aug '24

This RFC patchset suggests a new API for ASoC codec drivers to use for firmware/table downloads. Problem statement: All existing transfers initiated by codec drivers rely on SoundWire read/write commands, which can only support ONE byte per frame. With the typical 48kHz frame rate, this means 384 kbits/s. In addition, the command/control is typically handled with a FIFO and interrupts which adds more software overhead. To give a practical reference, sending 32Kb takes 2.5s on Intel platforms, which means about 105kbit/s only. Additional non-audio activity is likely to adversely impact interrupt scheduling and further decrease the transfer speeds. New SDCA-based codecs have a need to download tables and DSP firmware which are typically between 20 and 256 Kb. The slow bus operation has a direct impact on boot/resume times, and clearly having to wait more than 300ms is a showstopper in terms of latency requirements and user-experience. Suggested solution: The MIPI specification and most of the new codecs support the Bulk Transfer Protocol (BTP) and specifically the Bulk Register Access (BRA) configuration. This mode reclaims the 'audio' data space of the SoundWire frame to send firmware/coefficients over the DataPort 0 (DP0). The API suggested is rather simple, with the following sequence expected: open(): reserve resources and prepare hardware send_async(): trigger DMAs and perform SoundWire bank switch wait(): wait for DMA completion and disable DMAs close(): release resources Benefits: Even after accounting for the protocol overhead, the data can be sent 8x or 16x faster on the link than with the regular commands. With the use of DMAs, the software overhead becomes limited to the initialization. Measured results show that transferring the same 32Kb takes about 100ms, a 25x improvement on the baseline write() commands with an actual bitrate of 2.6 Mbits/s. These results are a measure of bus/hardware performance mainly, and will typically not be too modified by the CPU activity and scheduling. The performance for reads is similar, with a 25x speedup measured. Limitations: Setting up the transfers over DP0 takes time, and the reliance on DMAs on the host side brings alignment restrictions. The BTP/BRA protocol is really only relevant for "large" transfers done during boot/resume *before* audio transfers take place. Mixing BTP/BRA and audio is a nightmare, this patchset suggests a mutual-exclusion between two usages. Scope: This patchset only exposes the API and a debugfs interface to initiate commands, validate results and measure performance. The actual use of the API is left as an exercise for codec driver developers. This patchset depends on a number of pre-requisite patches and will not build on top of any for-next branches. The main intent of this RFC is to gather comments on the usage, API, benefits and restrictions. The code and functionality was tested on an Intel LunarLake RVP platform connected to a Realtek RT711-SDCA device. Acknowledgements: Thanks to Zeek Tsai at Realtek for providing test sequences that helped reconcile the data formatted by the host driver with the expected results on the code side. Pierre-Louis Bossart (16): Documentation: driver: add SoundWire BRA description soundwire: cadence: add BTP support for DP0 soundwire: stream: extend sdw_alloc_stream() to take 'type' parameter soundwire: extend sdw_stream_type to BPT soundwire: stream: special-case the bus compute_params() routine soundwire: stream: reuse existing code for BPT stream soundwire: bus: add API for BPT protocol soundwire: bus: add bpt_stream pointer soundwire: crc8: add constant table soundwire: cadence: add BTP/BRA helpers to format data soundwire: intel_auxdevice: add indirection for BPT open/close/send_async/wait ASoC: SOF: Intel: hda-sdw-bpt: add helpers for SoundWire BPT DMA soundwire: intel: add BPT context definition soundwire: intel_ace2x: add BPT open/close/send_async/wait soundwire: debugfs: add interface for BPT/BRA transfers ASoC: rt711-sdca: add DP0 support Documentation/driver-api/soundwire/bra.rst | 478 +++++++++++++ Documentation/driver-api/soundwire/index.rst | 1 + Documentation/driver-api/soundwire/stream.rst | 2 +- .../driver-api/soundwire/summary.rst | 5 +- drivers/soundwire/Kconfig | 1 + drivers/soundwire/Makefile | 4 +- drivers/soundwire/amd_manager.c | 2 +- drivers/soundwire/bus.c | 77 +++ drivers/soundwire/bus.h | 18 + drivers/soundwire/cadence_master.c | 646 +++++++++++++++++- drivers/soundwire/cadence_master.h | 30 + drivers/soundwire/crc8.c | 277 ++++++++ drivers/soundwire/crc8.h | 11 + drivers/soundwire/debugfs.c | 122 +++- .../soundwire/generic_bandwidth_allocation.c | 84 ++- drivers/soundwire/intel.h | 12 + drivers/soundwire/intel_ace2x.c | 377 ++++++++++ drivers/soundwire/intel_auxdevice.c | 55 ++ drivers/soundwire/qcom.c | 2 +- drivers/soundwire/stream.c | 137 +++- include/linux/soundwire/sdw.h | 91 ++- include/linux/soundwire/sdw_intel.h | 16 + include/sound/hda-sdw-bpt.h | 76 +++ sound/soc/codecs/rt711-sdca-sdw.c | 8 + sound/soc/qcom/sdw.c | 2 +- sound/soc/sof/intel/Kconfig | 8 +- sound/soc/sof/intel/Makefile | 4 + sound/soc/sof/intel/hda-sdw-bpt.c | 328 +++++++++ 28 files changed, 2810 insertions(+), 64 deletions(-) create mode 100644 Documentation/driver-api/soundwire/bra.rst create mode 100644 drivers/soundwire/crc8.c create mode 100644 drivers/soundwire/crc8.h create mode 100644 include/sound/hda-sdw-bpt.h create mode 100644 sound/soc/sof/intel/hda-sdw-bpt.c -- 2.39.2

4 60

[PATCH v11 00/10] spi: Add support for stacked/parallel memories
by Amit Kumar Mahapatra 19 Aug '24

19 Aug '24

This patch series updated the spi-nor, spi core and the AMD-Xilinx GQSPI driver to add stacked and parallel memories support. The first nine patches https://lore.kernel.org/all/20230119185342.2093323-1-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-2-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-3-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-4-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-5-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-6-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-7-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-8-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-9-amit.kumar-mahapatra@a… of the previous series got applied to https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next But the rest of the patches in the series did not get applied as failure was reported for spi driver with GPIO CS, so send the remaining patches in the series after rebasing it on top of for-next branch and fixing the issue. CS GPIO is not tested on our hardware, but it has been tested by @Stefan https://lore.kernel.org/all/005001da1efc$619ad5a0$24d080e0$@opensource.cirr… --- BRANCH: for-next Changes in v11: - Rebased patch series on top of latest for-next branch. - Added a new patch(1/10) to replace spi->chip_select with spi_get_chipselect() call in tps6594-spi.c. - Added a new patch(2/10) to replace spi->chip_select with spi_get_chipseletc() call in cs35l56_hda_spi.c. - In spi.c initialized unused CS[] to 0xff and spi->cs_index_mask to 0x01 in all flows. - Updated spi_dev_check() to compare the CS of old spi device with the new spi device CS. - Updated cover letter description to add information regarding GPIO CS testing and added Stefen's Tested-by tag in 3/10 patch. Changes in v10: - Rebased patch series on top of latest for-next branch and fixed merge conflicts. Changes in v9: - Updated 1/8 patch description to add an high-level overview of parallel(multi-cs) & stacked design. - Initialized all unused CS to 0xFF. - Moved CS check from spi_add_device() to __spi_add_device(). - Updated __spi_add_device() to check to make sure that multiple logical CS don't map to the same physical CS and same physical CS doesn't map to different logical CS. - Updated 1/8, 5/8 & 7/8 to support arbitrary number of flash devices connected in parallel or stacked mode. - Updated documentation for chip_select. - Added a new spi-nor structure member nor->num_flash to keep track of the number of flashes connected. - Added a new patch in the series 4/8 to move write_enable call just before spi_mem ops call in SPI-NOR. - Added comments in SPI core & SPI-NOR. - Rebased the patch series on top of the latest for-next branch. Changes in v8: - Updated __spi_add_device() and spi_set_cs() to fix spi driver failure with GPIO CS. - Rebased the patch series on top of latest for-next branch and fixed merge conflicts. - Updated cover letter description to add information regarding GPIO CS testing and request Stefan to provide his Tested-by tag for 1/7 patch. - Updated 1/7 patch description. Changes in v7: - Updated spi_dev_check() to avoid failures for spi driver GPIO CS and moved the error message from __spi_add_device() to spi_dev_check(). - Resolved code indentation issue in spi_set_cs(). - In spi_set_cs() call spi_delay_exec( ) once if the controller supports multi cs with both the CS backed by GPIO. - Updated __spi_validate()to add checks for both the GPIO CS. - Replaced cs_index_mask bit mask with SPI_CS_CNT_MAX. - Updated struct spi_controller to represent multi CS capability of the spi controller through a flag bit SPI_CONTROLLER_MULTI_CS instead of a boolen structure member "multi_cs_cap". - Updated 1/7 patch description . Changes in v6: - Rebased on top of latest v6.3-rc1 and fixed merge conflicts in spi-mpc512x-psc.c, sfdp.c, spansion.c files and removed spi-omap-100k.c. - Updated spi_dev_check( ) to reject new devices if any one of the chipselect is used by another device. Changes in v5: - Rebased the patches on top of v6.3-rc1 and fixed the merge conflicts. - Fixed compilation warnings in spi-sh-msiof.c with shmobile_defconfig Changes in v4: - Fixed build error in spi-pl022.c file - reported by Mark. - Fixed build error in spi-sn-f-ospi.c file. - Added Reviewed-by: Serge Semin <fancer.lancer(a)gmail.com> tag. - Added two more patches to replace spi->chip_select with API calls in mpc832x_rdb.c & cs35l41_hda_spi.c files. Changes in v3: - Rebased the patches on top of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next - Added a patch to convert spi_nor_otp_region_len(nor) & spi_nor_otp_n_regions(nor) macros into inline functions - Added Reviewed-by & Acked-by tags Changes in v2: - Rebased the patches on top of v6.2-rc1 - Created separate patch to add get & set APIs for spi->chip_select & spi->cs_gpiod, and replaced all spi->chip_select and spi->cs_gpiod references with the API calls. - Created separate patch to add get & set APIs for nor->params. --- Amit Kumar Mahapatra (10): mfd: tps6594: Use set/get APIs to access spi->chip_select ALSA: hda/cs35l56: Use set/get APIs to access spi->chip_select spi: Add multi-cs memories support in SPI core mtd: spi-nor: Convert macros with inline functions mtd: spi-nor: Add APIs to set/get nor->params mtd: spi-nor: Move write enable inside specific write & erase APIs mtd: spi-nor: Add stacked memories support in spi-nor spi: spi-zynqmp-gqspi: Add stacked memories support in GQSPI driver mtd: spi-nor: Add parallel memories support in spi-nor spi: spi-zynqmp-gqspi: Add parallel memories support in GQSPI driver drivers/mfd/tps6594-spi.c | 2 +- drivers/mtd/spi-nor/atmel.c | 17 +- drivers/mtd/spi-nor/core.c | 683 +++++++++++++++++++++++++------ drivers/mtd/spi-nor/core.h | 8 + drivers/mtd/spi-nor/debugfs.c | 4 +- drivers/mtd/spi-nor/gigadevice.c | 4 +- drivers/mtd/spi-nor/issi.c | 11 +- drivers/mtd/spi-nor/macronix.c | 10 +- drivers/mtd/spi-nor/micron-st.c | 35 +- drivers/mtd/spi-nor/otp.c | 48 ++- drivers/mtd/spi-nor/sfdp.c | 33 +- drivers/mtd/spi-nor/spansion.c | 57 +-- drivers/mtd/spi-nor/sst.c | 7 +- drivers/mtd/spi-nor/swp.c | 25 +- drivers/mtd/spi-nor/winbond.c | 2 +- drivers/mtd/spi-nor/xilinx.c | 18 +- drivers/spi/spi-zynqmp-gqspi.c | 58 ++- drivers/spi/spi.c | 259 ++++++++++-- include/linux/mtd/spi-nor.h | 21 +- include/linux/spi/spi.h | 51 ++- sound/pci/hda/cs35l56_hda_spi.c | 2 +- 21 files changed, 1085 insertions(+), 270 deletions(-) -- 2.17.1

10 61

[alsa-devel] unsupported variant of snd_hda_intel
by Alexandre 04 Jul '24

04 Jul '24

Hello, I have an Acer Aspire 4736G laptop. The soundcard that is shipped in this laptop is intel-hda based as shown (actually it's a realtek): cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0x9b300000 irq 46 Basic sound output is correct but few feature are missing: - internal mic seems to be found but do not works. - sound output stop working when trying to send it using HDMI output - heads do not work when plugged neither when forcing pulseaudio to use it. I have an ubuntu 10.10 which is shipped with alsa 1.0.23. I have googled around and tried loading the snd-hda-intel with several parameters () as found in HD-Audio-Models.txt to no avail. cat /proc/asound/pcm 00-00: ALC888 Analog : ALC888 Analog : playback 1 : capture 1 00-01: ALC888 Digital : ALC888 Digital : playback 1 00-03: NVIDIA HDMI : NVIDIA HDMI : playback 1 Where can I begin to help implement the support for this sound card? I have very skills in developement in general but am ready to try if it is not to hard (I supose I can use previous code for similar models).. I just need a shepherd. Thanks

4 4