February 2024 - Alsa-devel - mailman.alsa-project.org

[PATCH v18 00/41] Introduce QC USB SND audio offloading support
by Wesley Cheng 30 Mar '24

30 Mar '24

Several Qualcomm based chipsets can support USB audio offloading to a dedicated audio DSP, which can take over issuing transfers to the USB host controller. The intention is to reduce the load on the main processors in the SoC, and allow them to be placed into lower power modes. There are several parts to this design: 1. Adding ASoC binding layer 2. Create a USB backend for Q6DSP 3. Introduce XHCI interrupter support 4. Create vendor ops for the USB SND driver USB | ASoC -------------------------------------------------------------------- | _________________________ | |sm8250 platform card | | |_________________________| | | | | ___V____ ____V____ | |Q6USB | |Q6AFE | | |"codec" | |"cpu" | | |________| |_________| | ^ ^ ^ | | |________| | ___V____ | | |SOC-USB | | ________ ________ | | | |USB SND |<--->|QC offld|<------------>|________| | |(card.c)| | |<---------- | |________| |________|___ | | | ^ ^ | | | ____________V_________ | | | | | |APR/GLINK | __ V_______________V_____ | | | |______________________| |USB SND (endpoint.c) | | | | ^ |_________________________| | | | | ^ | | | ___________V___________ | | | |->|audio DSP | ___________V_____________ | | |_______________________| |XHCI HCD |<- | |_________________________| | Adding ASoC binding layer: soc-usb: Intention is to treat a USB port similar to a headphone jack. The port is always present on the device, but cable/pin status can be enabled/disabled. Expose mechanisms for USB backend ASoC drivers to communicate with USB SND. Create a USB backend for Q6DSP: q6usb: Basic backend driver that will be responsible for maintaining the resources needed to initiate a playback stream using the Q6DSP. Will be the entity that checks to make sure the connected USB audio device supports the requested PCM format. If it does not, the PCM open call will fail, and userpsace ALSA can take action accordingly. Introduce XHCI interrupter support: XHCI HCD supports multiple interrupters, which allows for events to be routed to different event rings. This is determined by "Interrupter Target" field specified in Section "6.4.1.1 Normal TRB" of the XHCI specification. Events in the offloading case will be routed to an event ring that is assigned to the audio DSP. Create vendor ops for the USB SND driver: qc_audio_offload: This particular driver has several components associated with it: - QMI stream request handler - XHCI interrupter and resource management - audio DSP memory management When the audio DSP wants to enable a playback stream, the request is first received by the ASoC platform sound card. Depending on the selected route, ASoC will bring up the individual DAIs in the path. The Q6USB backend DAI will send an AFE port start command (with enabling the USB playback path), and the audio DSP will handle the request accordingly. Part of the AFE USB port start handling will have an exchange of control messages using the QMI protocol. The qc_audio_offload driver will populate the buffer information: - Event ring base address - EP transfer ring base address and pass it along to the audio DSP. All endpoint management will now be handed over to the DSP, and the main processor is not involved in transfers. Overall, implementing this feature will still expose separate sound card and PCM devices for both the platorm card and USB audio device: 0 [SM8250MTPWCD938]: sm8250 - SM8250-MTP-WCD9380-WSA8810-VA-D SM8250-MTP-WCD9380-WSA8810-VA-DMIC 1 [Audio ]: USB-Audio - USB Audio Generic USB Audio at usb-xhci-hcd.1.auto-1.4, high speed This is to ensure that userspace ALSA entities can decide which route to take when executing the audio playback. In the above, if card#1 is selected, then USB audio data will take the legacy path over the USB PCM drivers, etc... This feature was validated using: - tinymix: set/enable the multimedia path to route to USB backend - tinyplay: issue playback on platform card Changelog -------------------------------------------- Changes in v18: - Rebased to usb-next, which merged in part of the series. Removed these patches. - Reworked Kconfigs for the ASoC USB related components from QCOM Q6DSP drivers to keep dependencies in place for SoC USB and USB SND. - Removed the repurposing of the stop ep sync API into existing XHCI operations. This will be solely used by the XHCI sideband for now. Changes in v17: - Fixed an issue where one patch was squashed into another. - Re-added some kconfig checks for helpers exposed in USB SND for the soc usb driver, after running different kconfigs. Changes in v16: - Modified some code layer dependencies so that soc usb can be split as a separate module. - Split the kcontrols from ASoC QCOM common layer into a separate driver - Reworked SOC USB kcontrols for controlling card + pcm offload routing and status so that there are individual controls for card and pcm devices. - Added a kcontrol remove API in SOC USB to remove the controls on the fly. This required to add some kcontrol management to SOC USB. - Removed the disconnect work and workqueue for the QC USB offload as it is not required, since QMI interface driver ensures events are handled in its own WQ. Changes in v15: - Removed some already merged XHCI changes - Separated SOC USB driver from being always compiled into SOC core. Now configurable from kconfig. - Fixed up ASoC kcontrol naming to fit guidelines. - Removed some unnecessary dummy ifdefs. - Moved usb snd offload capable kcontrol to be initialized by the platform offloading driver. Changes in v14: - Cleaned up some USB SND related feedback: - Renamed SNDUSB OFFLD playback available --> USB offload capable card - Fixed locking while checking if stream is in use - Replaced some mutex pairs with guard(mutex) Changes in v13: - Pulled in secondary/primary interrupter rework from Mathias from: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/drivers… - Did some cleanup and commit message updates, and tested on current code base. - Added mutex locking to xhci sideband to help prevent any race conditions, esp. for when accessing shared references. - Addresed concerns from Hillf about gfp_flags and locking used in qc_usb_audio_offload. - Rebased onto usb-next Changes in v12: - Updated copyright year to 2024. Happy new years! - Fixed newline format on mixer offload driver. Changes in v11: - Modified QMI format structures to be const Changes in v10: - Added new mixer for exposing kcontrol for sound card created by USB SND. This allows for applications to know which platform sound card has offload support. Will return the card number. - Broke down and cleaned up some functions/APIs within qc_audio_offload driver. - Exported xhci_initialize_ring_info(), and modified XHCI makefile to allow for the XHCI sideband to exist as a module. - Reworked the jack registration and moved it to the QCOM platform card driver, ie sm8250. - Added an SOC USB API to fetch a standard component tag that can be appended to the platform sound card. Added this tag to sm8250 if any USB path exists within the DT node. - Moved kcontrols that existed in the Q6USB driver, and made it a bit more generic, so that naming can be standardized across solutions. SOC USB is now responsible for creation of these kcontrols. - Added a SOC USB RST document explaining some code flows and implementation details so that other vendors can utilize the framework. - Addressed a case where USB device connection events are lost if usb offload driver (qc_audio_offload) is not probed when everything else has been initialized, ie USB SND, SOC USB and ASoC sound card. Add a rediscover device call during module init, to ensure that connection events will be propagated. - Rebased to usb-next. Changes in v9: - Fixed the dt binding check issue with regards to num-hc-interrupters. Changes in v8: - Cleaned up snd_soc_usb_find_priv_data() based on Mark's feedback. Removed some of the duplicate looping code that was present on previous patches. Also renamed the API. - Integrated Mathias' suggestions on his new sideband changes: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… - Addressed some of Mathias' fixme tags, such as: - Resetting transfer ring dequeue/enqueue pointers - Issuing stop endpoint command during ep removal - Reset ERDP properly to first segment ring during interrupter removal. (this is currently just being cleared to 0, but should be pointing to a valid segment if controller is still running. Changes in v7: - Fixed dt check error for q6usb bindings - Updated q6usb property from qcom,usb-audio-intr-num --> qcom,usb-audio-intr-idx - Removed separate DWC3 HC interrupters num property, and place limits to XHCI one. - Modified xhci_ring_to_sgtable() to use assigned IOVA/DMA address to fetch pages, as it is not ensured event ring allocated is always done in the vmalloc range. Changes in v6: - Fixed limits and description on several DT bindings (XHCI and Q6USB) - Fixed patch subjects to follow other ALSA/ASoC notations. USB SND - Addressed devices which expose multiple audio (UAC) interfaces. These devices will create a single USB sound card with multiple audio streams, and receive multiple interface probe routines. QC offload was not properly considering cases with multiple probe calls. - Renamed offload module name and kconfig to fit within the SND domain. - Renamed attach/detach endpoint API to keep the hw_params notation. Changes in v5: - Removed some unnescessary files that were included - Fixed some typos mentioned - Addressed dt-binding issues and added hc-interrupters definition to usb-xhci.yaml XHCI: - Moved secondary skip events API to xhci-ring and updated implementation - Utilized existing XHCI APIs, such as inc_deq and xhci_update_erst_dequeue() USB SND - Renamed and reworked the APIs in "sound: usb: Export USB SND APIs for modules" patch to include suggestions to utilize snd_usb_hw_params/free and to avoid generic naming. - Added a resume_cb() op for completion sake. - Addressed some locking concerns with regards to when registering for platform hooks. - Added routine to disconnect all offloaded devices during module unbind. ASoC - Replaced individual PCM parameter arguments in snd_soc_usb_connect() with new snd_soc_usb_device structure to pass along PCM info. - Modified snd_jack set report to notify HEADPHONE event, as we do not support record path. Changes in v4: - Rebased to xhci/for-usb-next - Addressed some dt-bindings comments XHCI: - Pulled in latest changes from Mathias' feature_interrupters branch: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… - Fixed commit text and signage for the XHCI sideband/interrupter related changes - Added some logic to address the FIXME tags mentioned throughout the commits, such as handling multi segment rings and building the SGT, locking concerns, and ep cleanup operations. - Removed some fixme tags for conditions that may not be needed/addressed. - Repurposed the new endpoint stop sync API to be utilized in other places. - Fixed potential compile issue if XHCI sideband config is not defined. ASoC: - Added sound jack control into the Q6USB driver. Allows for userpsace to know when an offload capable device is connected. USB SND: - Avoided exporting _snd_pcm_hw_param_set based on Takashi's recommendation. - Split USB QMI packet header definitions into a separate commit. This is used to properly allow the QMI interface driver to parse and route QMI packets accordingly - Added a "depends on" entry when enabling QC audio offload to avoid compile time issues. Changes in v3: - Changed prefix from RFC to PATCH - Rebased entire series to usb-next - Updated copyright years XHCI: - Rebased changes on top of XHCI changes merged into usb-next, and only added changes that were still under discussion. - Added change to read in the "num-hc-interrupters" device property. ASoC: - qusb6 USB backend - Incorporated suggestions to fetch iommu information with existing APIs - Added two new sound kcontrols to fetch offload status and offload device selection. - offload status - will return the card and pcm device in use tinymix -D 0 get 1 --> 1, 0 (offload in progress on card#1 pcm#0) - device selection - set the card and pcm device to enable offload on. Ex.: tinymix -D 0 set 1 2 0 --> sets offload on card#2 pcm#0 (this should be the USB card) USB SND: - Fixed up some locking related concerns for registering platform ops. - Moved callbacks under the register_mutex, so that - Modified APIs to properly pass more information about the USB SND device, so that the Q6USB backend can build a device list/map, in order to monitor offload status and device selection. Changes in v2: XHCI: - Replaced XHCI and HCD changes with Mathias' XHCI interrupter changes in his tree: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… Adjustments made to Mathias' changes: - Created xhci-intr.h to export/expose interrupter APIs versus exposing xhci.h. Moved dependent structures to this file as well. (so clients can parse out information from "struct xhci_interrupter") - Added some basic locking when requesting interrupters. - Fixed up some sanity checks. - Removed clearing of the ERSTBA during freeing of the interrupter. (pending issue where SMMU fault occurs if DMA addr returned is 64b - TODO) - Clean up pending events in the XHCI secondary interrupter. While testing USB bus suspend, it was seen that on bus resume, the xHCI HC would run into a command timeout. - Added offloading APIs to xHCI to fetch transfer and event ring information. ASoC: - Modified soc-usb to allow for multiple USB port additions. For this to work, the USB offload driver has to have a reference to the USB backend by adding a "usb-soc-be" DT entry to the device saved into XHCI sysdev. - Created separate dt-bindings for defining USB_RX port. - Increased APR timeout to accommodate the situation where the AFE port start command could be delayed due to having to issue a USB bus resume while handling the QMI stream start command. USB SND: - Added a platform ops during usb_audio_suspend(). This allows for the USB offload driver to halt the audio stream when system enters PM suspend. This ensures the audio DSP is not issuing transfers on the USB bus. - Do not override platform ops if they are already populated. - Introduce a shared status variable between the USB offload and USB SND layers, to ensure that only one path is active at a time. If the USB bus is occupied, then userspace is notified that the path is busy. Mathias Nyman (2): xhci: add helper to stop endpoint and wait for completion xhci: sideband: add initial api to register a sideband entity Wesley Cheng (39): usb: host: xhci: Export enable and disable interrupter APIs usb: host: xhci: Repurpose event handler for skipping interrupter events xhci: export XHCI IMOD setting helper for interrupters usb: host: xhci-sideband: Expose a sideband interrupter enable API usb: host: xhci-mem: Cleanup pending secondary event ring events usb: host: xhci-mem: Allow for interrupter clients to choose specific index ASoC: Add SOC USB APIs for adding an USB backend ASoC: dt-bindings: qcom,q6dsp-lpass-ports: Add USB_RX port ASoC: qcom: qdsp6: Introduce USB AFE port to q6dsp ASoC: qdsp6: q6afe: Increase APR timeout ASoC: qcom: qdsp6: Add USB backend ASoC driver for Q6 ALSA: usb-audio: Introduce USB SND platform op callbacks ALSA: usb-audio: Export USB SND APIs for modules ALSA: usb-audio: Save UAC sample size information usb: dwc3: Specify maximum number of XHCI interrupters usb: host: xhci-plat: Set XHCI max interrupters if property is present ALSA: usb-audio: qcom: Add USB QMI definitions ALSA: usb-audio: qcom: Introduce QC USB SND offloading support ALSA: usb-audio: Check for support for requested audio format ASoC: usb: Add PCM format check API for USB backend ASoC: qcom: qdsp6: Ensure PCM format is supported by USB audio device ALSA: usb-audio: Prevent starting of audio stream if in use ALSA: usb-audio: Do not allow USB offload path if PCM device is in use ASoC: dt-bindings: Update example for enabling USB offload on SM8250 ALSA: usb-audio: qcom: Populate PCM and USB chip information ASoC: qcom: qdsp6: Add support to track available USB PCM devices ASoC: Introduce SND kcontrols to select sound card and PCM device ASoC: qcom: qdsp6: Add SOC USB offload select get/put callbacks ASoC: Introduce SND kcontrols to track USB offloading state ASoC: qcom: qdsp6: Add PCM ops to track current state ASoC: usb: Create SOC USB SND jack kcontrol ASoC: qcom: qdsp6: Add headphone jack for offload connection status ASoC: usb: Fetch ASoC sound card information ALSA: usb-audio: Add USB offloading capable kcontrol ALSA: usb-audio: Allow for rediscovery of connected USB SND devices ALSA: usb-audio: qcom: Use card and PCM index from QMI request ASoC: usb: Rediscover USB SND devices on USB port add ASoC: qcom: Populate SoC components string ASoC: doc: Add documentation for SOC USB .../bindings/sound/qcom,sm8250.yaml | 15 + Documentation/sound/soc/index.rst | 1 + Documentation/sound/soc/usb.rst | 611 ++++++ drivers/usb/dwc3/core.c | 12 + drivers/usb/dwc3/core.h | 2 + drivers/usb/dwc3/host.c | 3 + drivers/usb/host/Kconfig | 9 + drivers/usb/host/Makefile | 2 + drivers/usb/host/xhci-mem.c | 37 +- drivers/usb/host/xhci-plat.c | 2 + drivers/usb/host/xhci-ring.c | 50 +- drivers/usb/host/xhci-sideband.c | 439 ++++ drivers/usb/host/xhci.c | 48 +- drivers/usb/host/xhci.h | 18 +- .../sound/qcom,q6dsp-lpass-ports.h | 1 + include/linux/usb/xhci-sideband.h | 70 + include/sound/q6usboffload.h | 20 + include/sound/soc-usb.h | 182 ++ sound/soc/Kconfig | 10 + sound/soc/Makefile | 2 + sound/soc/qcom/Kconfig | 15 + sound/soc/qcom/Makefile | 2 + sound/soc/qcom/qdsp6/Makefile | 1 + sound/soc/qcom/qdsp6/q6afe-dai.c | 60 + sound/soc/qcom/qdsp6/q6afe.c | 193 +- sound/soc/qcom/qdsp6/q6afe.h | 36 +- sound/soc/qcom/qdsp6/q6dsp-lpass-ports.c | 23 + sound/soc/qcom/qdsp6/q6dsp-lpass-ports.h | 1 + sound/soc/qcom/qdsp6/q6routing.c | 9 + sound/soc/qcom/qdsp6/q6usb.c | 408 ++++ sound/soc/qcom/sm8250.c | 15 +- sound/soc/qcom/usb_offload_utils.c | 51 + sound/soc/qcom/usb_offload_utils.h | 26 + sound/soc/soc-usb.c | 660 ++++++ sound/usb/Kconfig | 25 + sound/usb/Makefile | 2 +- sound/usb/card.c | 109 + sound/usb/card.h | 15 + sound/usb/endpoint.c | 1 + sound/usb/format.c | 1 + sound/usb/helper.c | 1 + sound/usb/pcm.c | 104 +- sound/usb/pcm.h | 11 + sound/usb/qcom/Makefile | 6 + sound/usb/qcom/mixer_usb_offload.c | 65 + sound/usb/qcom/mixer_usb_offload.h | 17 + sound/usb/qcom/qc_audio_offload.c | 1914 +++++++++++++++++ sound/usb/qcom/usb_audio_qmi_v01.c | 892 ++++++++ sound/usb/qcom/usb_audio_qmi_v01.h | 162 ++ 49 files changed, 6306 insertions(+), 53 deletions(-) create mode 100644 Documentation/sound/soc/usb.rst create mode 100644 drivers/usb/host/xhci-sideband.c create mode 100644 include/linux/usb/xhci-sideband.h create mode 100644 include/sound/q6usboffload.h create mode 100644 include/sound/soc-usb.h create mode 100644 sound/soc/qcom/qdsp6/q6usb.c create mode 100644 sound/soc/qcom/usb_offload_utils.c create mode 100644 sound/soc/qcom/usb_offload_utils.h create mode 100644 sound/soc/soc-usb.c create mode 100644 sound/usb/qcom/Makefile create mode 100644 sound/usb/qcom/mixer_usb_offload.c create mode 100644 sound/usb/qcom/mixer_usb_offload.h create mode 100644 sound/usb/qcom/qc_audio_offload.c create mode 100644 sound/usb/qcom/usb_audio_qmi_v01.c create mode 100644 sound/usb/qcom/usb_audio_qmi_v01.h

2 47

[PATCH 0/7] Soundwire: clean up sysfs group creation
by Greg Kroah-Hartman 28 Mar '24

28 Mar '24

Note, this is a redone version of a very old series I wrote back in 2022: https://lore.kernel.org/r/20220824135951.3604059-1-gregkh@linuxfoundation.o… but everyone has forgotten about it now, and I've reworked it, so I'm considering it a "new" version, and not v2. Here's a series that adds the functionality to the driver core to hide entire attribute groups, in a much saner way than we have attempted in the past (i.e. dynamically figuring it out.) Many thanks to Dan for this patch. I'll also be taking this into my driver-core branch and creating a stable tag for anyone else to pull from to get it into their trees, as I think it will want to be in many for this development cycle. After the driver core change, there's cleanups to the soundwire core for how the attribute groups are created, to remove the "manual" creation of them, and allow the driver core to create them correctly, as needed, when needed, which makes things much smaller for the soundwire code to manage. Comments appreciated! thanks, greg k-h Dan Williams (1): sysfs: Introduce a mechanism to hide static attribute_groups Greg Kroah-Hartman (5): soundwire: sysfs: move sdw_slave_dev_attr_group into the existing list of groups soundwire: sysfs: cleanup the logic for creating the dp0 sysfs attributes soundwire: sysfs: have the driver core handle the creation of the device groups soundwire: sysfs: remove sdw_slave_sysfs_init() soundwire: sysfs: remove unneeded ATTRIBUTE_GROUPS() comments drivers/soundwire/bus_type.c | 5 ++- drivers/soundwire/sysfs_local.h | 4 +- drivers/soundwire/sysfs_slave.c | 64 ++++++++++++++--------------- drivers/soundwire/sysfs_slave_dpn.c | 3 ++ fs/sysfs/group.c | 45 ++++++++++++++++---- include/linux/sysfs.h | 63 ++++++++++++++++++++++------ 6 files changed, 126 insertions(+), 58 deletions(-) -- 2.43.0

5 22

[PATCH 0/7] ASoC: mediatek: AFE drivers cleanups
by AngeloGioacchino Del Regno 26 Mar '24

26 Mar '24

This series converts MediaTek AFE drivers' probe functions to use dev_err_probe() and devm functions where possible and, in some cases, dropping the .remove_new() callback, reducing the size. Cheers! AngeloGioacchino Del Regno (7): ASoC: mediatek: mt8173-afe-pcm: Convert to devm_pm_runtime_enable() ASoC: mediatek: mt8173-afe-pcm: Use devm_snd_soc_register_component() ASoC: mediatek: mt8183-afe-pcm: Convert to devm_pm_runtime_enable() ASoC: mediatek: mt8183-afe-pcm: Simplify with dev_err_probe() ASoC: mediatek: mt8192-afe-pcm: Convert to devm_pm_runtime_enable() ASoC: mediatek: mt8192-afe-pcm: Simplify with dev_err_probe() ASoC: mediatek: mt8195-afe-pcm: Drop .remove_new() callback sound/soc/mediatek/mt8173/mt8173-afe-pcm.c | 78 +++------------ sound/soc/mediatek/mt8183/mt8183-afe-pcm.c | 108 +++++++-------------- sound/soc/mediatek/mt8192/mt8192-afe-pcm.c | 95 ++++++------------ sound/soc/mediatek/mt8195/mt8195-afe-pcm.c | 12 +-- 4 files changed, 81 insertions(+), 212 deletions(-) -- 2.43.0

5 15

[PATCH 0/2] ALSA/ASoC/SOF: SSP dev_type support
by Peter Ujfalusi 26 Mar '24

26 Mar '24

Hi, SOF always passed 0 as dev_type to intel_nhlt_get_endpoint_blob() when looking up the blob from the NHLT table. This causes issues since alsa-utils commit 3a47ef2487ed ("topology: nhlt: intel: support more device types and directions") The dev_type is no longer always 0 in the topology embedded NHLT table resulting lookup failures for analog codecs since they will have dev_type=4. With SOF the dev_type is not used, we always use the SSP port index for looking up the configuration blob. The solution for the issue is to fetch the dev_type for the SSP port and feed it back to the intel_nhlt_get_endpoint_blob() to be able to find the configuration regardless of the assigned dev_type. Regards, Peter --- Brent Lu (2): ALSA: hda: intel-nhlt: add intel_nhlt_ssp_device_type() function ASoC: SOF: ipc4-topology: support NHLT device type include/sound/intel-nhlt.h | 10 ++++++++++ sound/hda/intel-nhlt.c | 26 ++++++++++++++++++++++++++ sound/soc/sof/ipc4-topology.c | 19 ++++++++++++++++--- 3 files changed, 52 insertions(+), 3 deletions(-) -- 2.43.0

3 6

[PATCH v3 00/32] spi: get rid of some legacy macros
by Uwe Kleine-König 25 Mar '24

25 Mar '24

Changes since v2 (https://lore.kernel.org/linux-spi/cover.1705944943.git.u.kleine-koenig@peng…): - Drop patch "mtd: rawnand: fsl_elbc: Let .probe retry if local bus is missing" which doesn't belong into this series. - Fix a build failure noticed by the kernel build bot in drivers/spi/spi-au1550.c. (I failed to catch this because this driver is mips only, but not enabled in a mips allmodconfig. That's a bit unfortunate, but not easily fixable.) - Add the Reviewed-by: and Acked-by: tags I received for v2. Mark already announced for v2 that he is willing to apply the whole series to his spi tree. Assuming no other show stoper are found in this v3, I assume that's the plan still for this series now. Thanks Uwe Uwe Kleine-König (32): fpga: ice40-spi: Follow renaming of SPI "master" to "controller" ieee802154: ca8210: Follow renaming of SPI "master" to "controller" iio: adc: ad_sigma_delta: Follow renaming of SPI "master" to "controller" Input: pxspad - follow renaming of SPI "master" to "controller" Input: synaptics-rmi4 - follow renaming of SPI "master" to "controller" media: mgb4: Follow renaming of SPI "master" to "controller" media: netup_unidvb: Follow renaming of SPI "master" to "controller" media: usb/msi2500: Follow renaming of SPI "master" to "controller" media: v4l2-subdev: Follow renaming of SPI "master" to "controller" misc: gehc-achc: Follow renaming of SPI "master" to "controller" mmc: mmc_spi: Follow renaming of SPI "master" to "controller" mtd: dataflash: Follow renaming of SPI "master" to "controller" net: ks8851: Follow renaming of SPI "master" to "controller" net: vertexcom: mse102x: Follow renaming of SPI "master" to "controller" platform/chrome: cros_ec_spi: Follow renaming of SPI "master" to "controller" spi: bitbang: Follow renaming of SPI "master" to "controller" spi: cadence-quadspi: Don't emit error message on allocation error spi: cadence-quadspi: Follow renaming of SPI "master" to "controller" spi: cavium: Follow renaming of SPI "master" to "controller" spi: geni-qcom: Follow renaming of SPI "master" to "controller" spi: loopback-test: Follow renaming of SPI "master" to "controller" spi: slave-mt27xx: Follow renaming of SPI "master" to "controller" spi: spidev: Follow renaming of SPI "master" to "controller" staging: fbtft: Follow renaming of SPI "master" to "controller" staging: greybus: spi: Follow renaming of SPI "master" to "controller" tpm_tis_spi: Follow renaming of SPI "master" to "controller" usb: gadget: max3420_udc: Follow renaming of SPI "master" to "controller" video: fbdev: mmp: Follow renaming of SPI "master" to "controller" wifi: libertas: Follow renaming of SPI "master" to "controller" spi: fsl-lib: Follow renaming of SPI "master" to "controller" spi: Drop compat layer from renaming "master" to "controller" Documentation: spi: Update documentation for renaming "master" to "controller" .../driver-api/driver-model/devres.rst | 2 +- Documentation/spi/spi-summary.rst | 74 +++++++++---------- drivers/char/tpm/tpm_tis_spi_main.c | 4 +- drivers/fpga/ice40-spi.c | 4 +- drivers/iio/adc/ad_sigma_delta.c | 14 ++-- drivers/input/joystick/psxpad-spi.c | 4 +- drivers/input/rmi4/rmi_spi.c | 2 +- drivers/media/pci/mgb4/mgb4_core.c | 14 ++-- .../media/pci/netup_unidvb/netup_unidvb_spi.c | 48 ++++++------ drivers/media/usb/msi2500/msi2500.c | 38 +++++----- drivers/media/v4l2-core/v4l2-spi.c | 4 +- drivers/misc/gehc-achc.c | 8 +- drivers/mmc/host/mmc_spi.c | 6 +- drivers/mtd/devices/mtd_dataflash.c | 2 +- drivers/net/ethernet/micrel/ks8851_spi.c | 4 +- drivers/net/ethernet/vertexcom/mse102x.c | 2 +- drivers/net/ieee802154/ca8210.c | 2 +- .../net/wireless/marvell/libertas/if_spi.c | 2 +- drivers/platform/chrome/cros_ec_spi.c | 8 +- drivers/spi/spi-ath79.c | 4 +- drivers/spi/spi-au1550.c | 2 +- drivers/spi/spi-bitbang.c | 64 ++++++++-------- drivers/spi/spi-butterfly.c | 6 +- drivers/spi/spi-cadence-quadspi.c | 7 +- drivers/spi/spi-cavium.c | 6 +- drivers/spi/spi-cavium.h | 2 +- drivers/spi/spi-davinci.c | 6 +- drivers/spi/spi-fsl-lib.c | 14 ++-- drivers/spi/spi-geni-qcom.c | 2 +- drivers/spi/spi-gpio.c | 2 +- drivers/spi/spi-lm70llp.c | 6 +- drivers/spi/spi-loopback-test.c | 4 +- drivers/spi/spi-oc-tiny.c | 6 +- drivers/spi/spi-omap-uwire.c | 4 +- drivers/spi/spi-sh-sci.c | 10 +-- drivers/spi/spi-slave-mt27xx.c | 2 +- drivers/spi/spi-xilinx.c | 4 +- drivers/spi/spi-xtensa-xtfpga.c | 2 +- drivers/spi/spi.c | 2 +- drivers/spi/spidev.c | 2 +- drivers/staging/fbtft/fbtft-core.c | 4 +- drivers/staging/greybus/spilib.c | 66 ++++++++--------- drivers/usb/gadget/udc/max3420_udc.c | 2 +- drivers/video/fbdev/mmp/hw/mmp_spi.c | 26 +++---- include/linux/spi/spi.h | 20 +---- include/linux/spi/spi_bitbang.h | 2 +- include/media/v4l2-common.h | 6 +- 47 files changed, 253 insertions(+), 272 deletions(-) base-commit: b9b98f594b6f4c0b0fb2da4493453aef183bca4b -- 2.43.0

3 4

synaptics hi-res audio usb device duplex, usb bandwidth issues
by Ian Malone 21 Mar '24

21 Mar '24

Hi, In short I have a USB to 3.5mm adapter which seems not to work in duplex mode on USB2.0 systems, possibly due to a bandwidth calculation bug. This is an evolution of an issue I previously posted on the users list with no luck. I have an Anker USB-C to 3.5mm audio dongle (lsusb: Conexant Systems (Rockwell), Inc. Hi-Res Audio) which I've used for some time on my phone (Android with USB-3.2). On trying to use it with an older T420 laptop recently with only USB-2.0 ports I discovered it will not work in duplex mode. Input-only and output-only profiles work (tested recording and playback with audacity), but with duplex no sound is recorded (Fedora 39, pipewire). This is easily reproduced by looking at the pavucontrol volume monitor for Output Devices, if I switch the device to Analog or Digital Input in configuration then the Input Devices level monitor for it shows activity if I speak into or tap the microphone. With duplex selected there is no activity, the level monitor bar may or may not display. I can switch between the two behaviours by changing the profile. Various applications such as Audacity and Zoom appear to hang when accessing this microphone with the duplex profile set. I've used pipewire configuration to force the format to 16LE only (playback and recording), but this has not helped. In dmesg this error appears when this happens (microphone opened, for example by pavucontrol): [ 294.825544] usb 1-1.1: cannot submit urb 0, error -28: not enough bandwidth (T420, Fedora 39, kernel 6.7.5) The T420 has USB 2 Type A ports, so a Type C to Type A adapter is needed, but the problem is not limited to the T420 laptop. On an older Samsung Tablet (Tab-A 2019, USB-2.0 Type C, kernel 4.4.177) I've been able to test using Google Meet. Although there are no errors or freezing observed, in headphone mode over USB the headphone microphone is not being used and the tablet uses its onboard microphone instead (although headphones are selected and playback is over the headphones). Again, I can record (via voice recorder) from the headset microphone, just no duplex. Trying google meet on my phone (USB3.2) I do get duplex over the USB-3.5 adapter. On a newer laptop with USB-3.2 and a mix of type A and C ports I also get duplex (F37, kernel 6.5.12), however dmesg shows even here not all is well, using the type A and C ports on the side: [ 9172.326602] usb 3-1: new full-speed USB device number 6 using xhci_hcd [ 9172.490169] usb 3-1: New USB device found, idVendor=0572, idProduct=1b08, bcdDevice= 0.10 [ 9172.490174] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 9172.490177] usb 3-1: Product: Hi-Res Audio [ 9172.490178] usb 3-1: Manufacturer: Synaptics [ 9172.490180] usb 3-1: SerialNumber: 000000000000000000000000 [ 9172.683435] input: Synaptics Hi-Res Audio as /devices/pci0000:00/0000:00:08.1/0000:05:00.4/usb3/3-1/3-1:1.3/0003:0572:1B08.000A/input/input36 [ 9172.736025] hid-generic 0003:0572:1B08.000A: input,hidraw5: USB HID v1.11 Device [Synaptics Hi-Res Audio] on usb-0000:05:00.4-1/input3 [ 9173.386988] usb 3-1: Not enough bandwidth for new device state. [ 9173.386994] usb 3-1: Not enough bandwidth for altsetting 1 [ 9173.386996] endpoint_set_interface: 70 callbacks suppressed [ 9173.386998] usb 3-1: 1:1: usb_set_interface failed (-28) [ 9173.387110] usb 3-1: Not enough bandwidth for new device state. [ 9173.387113] usb 3-1: Not enough bandwidth for altsetting 1 (...these 3 lines repeat 9 more times, followed by...) [ 9173.388785] usb 3-1: Not enough bandwidth for new device state. [ 9173.388789] usb 3-1: Not enough bandwidth for altsetting 1 (...these 2 lines repeat 5 more times, then stop) This is a USB3.2 system, the onboard camera has a hardware switch, so I can disable it, and the only other peripheral that appears is the AX210 bluetooth (I'd thought that would have its own bus as it's part of a separate wifi chip, but apparently not, lsusb -t below), bandwidth for even a 96kHz 24bit duplex audio device shouldn't really be an issue. $ lsusb Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 003: ID 8087:0032 Intel Corp. AX210 Bluetooth Bus 003 Device 002: ID 048d:c965 Integrated Technology Express, Inc. ITE Device(8295) Bus 003 Device 007: ID 0572:1b08 Conexant Systems (Rockwell), Inc. Hi-Res Audio Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 002: ID 0bda:0411 Realtek Semiconductor Corp. Hub Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 004: ID 048d:c101 Integrated Technology Express, Inc. ITE Device(8910) Bus 001 Device 002: ID 0bda:5411 Realtek Semiconductor Corp. RTS5411 Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub $ lsusb -t /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 480M |__ Port 1: Dev 7, If 0, Class=Audio, Driver=snd-usb-audio, 12M |__ Port 1: Dev 7, If 1, Class=Audio, Driver=snd-usb-audio, 12M |__ Port 1: Dev 7, If 2, Class=Audio, Driver=snd-usb-audio, 12M |__ Port 1: Dev 7, If 3, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 3: Dev 2, If 0, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 3: Dev 2, If 1, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 4: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M |__ Port 4: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M |__ Port 2: Dev 2, If 0, Class=Hub, Driver=hub/4p, 5000M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 480M |__ Port 2: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 4: Dev 4, If 0, Class=Human Interface Device, Driver=usbhid, 12M The only situation in which I *don't* get these dmesg errors is if I use one of the rear USB 3.2 ports that seem to lead to it being on its own bus: $ lsusb -t /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 480M |__ Port 3: Dev 2, If 0, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 3: Dev 2, If 1, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 4: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M |__ Port 4: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 10000M |__ Port 2: Dev 2, If 0, Class=Hub, Driver=hub/4p, 5000M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 480M |__ Port 2: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M |__ Port 2: Dev 7, If 0, Class=Audio, Driver=snd-usb-audio, 12M |__ Port 2: Dev 7, If 1, Class=Audio, Driver=snd-usb-audio, 12M |__ Port 2: Dev 7, If 2, Class=Audio, Driver=snd-usb-audio, 12M |__ Port 2: Dev 7, If 3, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 4: Dev 4, If 0, Class=Human Interface Device, Driver=usbhid, 12M In this case the dmesg output is clear after device connection. This seems like some kind of bandwidth calculation problem in snd_usb_audio. I've tried building a kernel and modifying various of the defines in sound/usb/card.h (currently MAX_PACKS 4 and MAX_PACKS_HS (MAX_PACKS * 4), compared to 6 and *8) but not hit on a winning formula yet. Is there any information I could collect to try to fix this? -- imalone

2 6

[PATCH v9 00/27] Add support for QMC HDLC, framer infrastructure and PEF2256 framer
by Herve Codina 14 Mar '24

14 Mar '24

Hi, I have a system where I need to handle an HDLC interface and some audio data. The HDLC data are transferred using a TDM bus on which a PEF2256 (E1/T1 framer) is present. The PEF2256 transfers data from/to the TDM bus to/from the E1 line. This PEF2256 is connected to a PowerQUICC SoC for the control path and the TDM is connected to the SoC (QMC component) for the data path. From the QMC HDLC driver, I need to handle HDLC data using the QMC, carrier detection using the PEF2256 (E1 line carrier) and set/get some PEF2256 configuration. The QMC HDLC driver considers the PEF2256 as a generic framer. It performs operations that involve the PEF2256 through the generic framer API. The audio data are exchanged with the PEF2256 using a CPU DAI connected to the TDM bus through the QMC and the PEF2256 needs to be seen as a codec in order to be linked to the CPU DAI. The codec handles the carrier detection using the PEF2256 and reports the carrier state to the ALSA subsystem using the ASoC jack detection. The codec, even if instantiated by the PEF2256 driver, considers the PEF2256 as a generic framer. The generic framer has: - 2 consumers (QMC HDLC drv and codec) - 1 provider (PEF2256) So, the design is the following: +------------------+ +---------+ | QMC | <- TDM -> | PEF2256 | <-> E1 +---------+ | +-------------+ | | | | CPU DAI | <-data--> | QMC channel | | | | +---------+ | +-------------+ | | | +--------------+ | +-------------+ | | | | QMC HDLC drv | <-data--> | QMC channel | | | | +--------------+ | +-------------+ | | | ^ +------------------+ | | | +--------+ +-------------+ | | +-> | framer | <-> | PEF2256 drv | <- local bus ->| | | | | | +---------+ +-> | | | | | +--------+ | +-------+ | +-------------------> | codec | | | +-------+ | +-------------+ Further more, the TDM timeslots used by the QMC HDLC driver need to be configured at runtime (QMC dynamic timeslots). Several weeks ago, I sent two series related to this topic: - Add the Lantiq PEF2256 audio support [1] - RFC Add support for QMC HDLC and PHY [2] This current series is a rework of these two series taking into account feedbacks previously received. In order to implement all of this, I do the following: 1) Perform some fixes (patches 1, 2, 3, 4, 5 ) 2) Introduce the QMC HDLC driver (patches 6, 7, 8) 3) Add QMC dynamic timeslot support (patches 9 - 19) 4) Add timeslots change support in QMC HDLC (patch 20) 5) Introduce framer infrastructure (patch 21) 6) Add PEF2256 framer provider (patches 22, 23, 24, 25) 7) Add framer codec as a framer consumer (patch 26) 8) Add framer support as a framer consumer in QMC HDLC (patch 27) The series contains the full story and detailed modifications. If needed, the series can be split and/or commits can be squashed. Let me know. Compare to the previous iteration https://lore.kernel.org/linux-kernel/20231011061437.64213-1-herve.codina@bo… This v9 series: - Removes some patches already applied - Adds some 'Acked-by' tags Best regards, Hervé [1]: https://lore.kernel.org/all/20230417171601.74656-1-herve.codina@bootlin.com/ [2]: https://lore.kernel.org/all/20230323103154.264546-1-herve.codina@bootlin.co… Changes v8 -> v9 - Removed Patches 6, 7 and 8 (patches applied) - Patches 7, 20, 21, 23 (patches 10, 23, 24, 26 in v8) Add 'Acked-by: Jakub Kicinski <kuba(a)kernel.org>' Changes v7 -> v8 - Patch 10 Fix a race condition when stopping the queue in qmc_hdlc_close() - Patch 24 Move to menuconfig and hide CONFIG_GENERIC_FRAMER Remove unneeded check (defensive programming) Remove unneeded variable assignment - Patch 25 Add 'Reviewed-by: Rob Herring <robh(a)kernel.org>' - Patch 26 Use array notation for 'audio_devs' Changes v6 -> v7 - Patch 8 Move the 'compatible' property to the first property. Add device/SoC specific compatible strings. Add 'Reviewed-by: Rob Herring <robh(a)kernel.org>' - Patch 25 Remove '$ref' from the lantiq,data-rate-bps property. '-bps' is now a standard suffix. Changes v5 -> v6 - All patches Remove 'Signed-off-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' These Sob were added by Christophe when he sent the v4 while I was on vacation. https://lore.kernel.org/linux-kernel/992a2b31-e21f-eee3-8bfc-a65b69fe5bd7@c… - Patch 6, 7 Add 'Acked-by: Conor Dooley <conor.dooley(a)microchip.com>' Add 'Acked-by: Rob Herring <robh(a)kernel.org>' - Patch 8 Add a constraint on fsl,framer. - Patch 25 Fix clocks description (inconsistent capitalisation) Use '8-bit' instead of '8bit' Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Removed patch 26 (patch applied) - Patch 26 (patch 27 in v5) Add 'Reviewed-by: Linus Walleij <linus.walleij(a)linaro.org>' - Patch 27 (patch 28 in v5) Move registers definition to .c file and remove .h file Add 'select PINCONF' in Kconfig Use dev_err_probe() Add 'Reviewed-by: Linus Walleij <linus.walleij(a)linaro.org>' - Patch 28 (patch 29 in v5) Remove .h file Changes v4 -> v5 - Patches 1 to 5 No changes - Patch 6 (new in v5) Fix QMC binding example - Patch 7 (new in v5) Add missing 'additionalProperties: false' - Patch 8 (new in v5, replace v4 patch 6) Add QMC HDLC properties in the QMC channel node Renamed the 'framer' property to 'fsl,framer' - Patch 9 (new in v5) Add support for QMC child devices - Patch 10 (patch 7 in v4) No changes - Patch 11 (patch 8 in v4) Remove fsl,qmc-hdlc.yaml (no more existing file) - Patches 12 to 22 (patches 9 to 19 in v4) No changes - Patch 23 (patch 20 in v4) Remove unused variable initializations Remove extra space - Patch 24 (patch 21 in v4) Improve Kconfig help text Fix variable declaration (reverse xmas tree) Fix typos and extra spaces Fix documentation issues raised by 'kernel-doc -none' Move of_node_put() and kfree() out of the mutex Replace ida_simple_{get,remove}() by ida_{alloc,free}() Support framer device-tree nodes without '#framer-cells' property - Patch 25 (patch 22 in v4) Fix $ref in the pinctrl subnode Remove '#framer-cells' property Add needed '|' - Patch 26 (patch 23 in v4) Fix a typo in the commit subject - Patches 27, 28, 29 (patch 24, 25, 26 in v4) No changes - Patch 30 (patch 27 in v4) Fix a typo in the commit log - Patch 31 (patch 28 in v4) Used 'fsl,framer' property name instead of 'framer' Changes v3 -> v4 - Patch 21 Fixes build failure with CONFIG_MODULES Changes v2 -> v3 - Patches 1, 2, 3, 4 Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - New patch Remove inline keyword from the existing registers accessors helpers - Patch 6 (patches 5, 27 in v2) Update the binding title Squash patch 27 - Patch 7 (patch 6 in v2) Remove the cast in netdev_to_qmc_hdlc() Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 8 (patch 7 in v2): No change - Patches 9, 10 (patches 8, 9 in v2) Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 11 (patch 10 in v2) Remove inline keyword from the introduced qmc_clrsetbits16() helper Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patches 12, 13, 14, 15, 16, 17, 18, 19, 20 Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 21 (patch 20 in v2) Remove unneeded framer NULL pointer check Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 22 (patch 21 in v2) Change sclkr and sclkx clocks description Remove the framer phandle property from the framer subnodes (ie. from framer-codec nodes) - Patch 23 (patch 22 in v2) Initialize 'disabled' variable at declaration Fix commit log Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 24 (patch 23 in v2) Remove inline keyword from the existing registers accessors helpers Use dev_warn_ratelimited() in default interrupt handler Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 25 (patch 24 in v2) Replace #include "linux/bitfield.h" by #include <linux/bitfield.h> Fold the pinctrl anonymous struct into the struct pef2256_pinctrl Update commit log Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 26 (patch 25 in v2) Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 27 (patch 26 in v2) Fix error message Changed the ch.max computation in framer_dai_hw_rule_channels_by_format() Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 28 Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' Changes v1 -> v2 - Patches 1, 2 (New in v2) Fix __iomem addresses declaration - Patch 19 (17 in v1) Fix a compilation warning - Patch 26 (24 in v1) Fix a typo in Kconfig file Fix issues raised by sparse (make C=1) Herve Codina (27): soc: fsl: cpm1: tsa: Fix __iomem addresses declaration soc: fsl: cpm1: qmc: Fix __iomem addresses declaration soc: fsl: cpm1: qmc: Fix rx channel reset soc: fsl: cpm1: qmc: Extend the API to provide Rx status soc: fsl: cpm1: qmc: Remove inline function specifiers soc: fsl: cpm1: qmc: Add support for child devices net: wan: Add support for QMC HDLC MAINTAINERS: Add the Freescale QMC HDLC driver entry soc: fsl: cpm1: qmc: Introduce available timeslots masks soc: fsl: cpm1: qmc: Rename qmc_setup_tsa* to qmc_init_tsa* soc: fsl: cpm1: qmc: Introduce qmc_chan_setup_tsa* soc: fsl: cpm1: qmc: Remove no more needed checks from qmc_check_chans() soc: fsl: cpm1: qmc: Check available timeslots in qmc_check_chans() soc: fsl: cpm1: qmc: Add support for disabling channel TSA entries soc: fsl: cpm1: qmc: Split Tx and Rx TSA entries setup soc: fsl: cpm1: qmc: Introduce is_tsa_64rxtx flag soc: fsl: cpm1: qmc: Handle timeslot entries at channel start() and stop() soc: fsl: cpm1: qmc: Remove timeslots handling from setup_chan() soc: fsl: cpm1: qmc: Introduce functions to change timeslots at runtime wan: qmc_hdlc: Add runtime timeslots changes support net: wan: Add framer framework support dt-bindings: net: Add the Lantiq PEF2256 E1/T1/J1 framer net: wan: framer: Add support for the Lantiq PEF2256 framer pinctrl: Add support for the Lantic PEF2256 pinmux MAINTAINERS: Add the Lantiq PEF2256 driver entry ASoC: codecs: Add support for the framer codec net: wan: fsl_qmc_hdlc: Add framer support .../bindings/net/lantiq,pef2256.yaml | 213 +++++ MAINTAINERS | 15 + drivers/net/wan/Kconfig | 14 + drivers/net/wan/Makefile | 3 + drivers/net/wan/framer/Kconfig | 41 + drivers/net/wan/framer/Makefile | 7 + drivers/net/wan/framer/framer-core.c | 882 ++++++++++++++++++ drivers/net/wan/framer/pef2256/Makefile | 8 + drivers/net/wan/framer/pef2256/pef2256-regs.h | 250 +++++ drivers/net/wan/framer/pef2256/pef2256.c | 880 +++++++++++++++++ drivers/net/wan/fsl_qmc_hdlc.c | 820 ++++++++++++++++ drivers/pinctrl/Kconfig | 15 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-pef2256.c | 358 +++++++ drivers/soc/fsl/qe/qmc.c | 592 +++++++++--- drivers/soc/fsl/qe/tsa.c | 22 +- include/linux/framer/framer-provider.h | 194 ++++ include/linux/framer/framer.h | 205 ++++ include/linux/framer/pef2256.h | 31 + include/soc/fsl/qe/qmc.h | 27 +- sound/soc/codecs/Kconfig | 15 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/framer-codec.c | 413 ++++++++ sound/soc/fsl/fsl_qmc_audio.c | 2 +- 24 files changed, 4873 insertions(+), 137 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/lantiq,pef2256.yaml create mode 100644 drivers/net/wan/framer/Kconfig create mode 100644 drivers/net/wan/framer/Makefile create mode 100644 drivers/net/wan/framer/framer-core.c create mode 100644 drivers/net/wan/framer/pef2256/Makefile create mode 100644 drivers/net/wan/framer/pef2256/pef2256-regs.h create mode 100644 drivers/net/wan/framer/pef2256/pef2256.c create mode 100644 drivers/net/wan/fsl_qmc_hdlc.c create mode 100644 drivers/pinctrl/pinctrl-pef2256.c create mode 100644 include/linux/framer/framer-provider.h create mode 100644 include/linux/framer/framer.h create mode 100644 include/linux/framer/pef2256.h create mode 100644 sound/soc/codecs/framer-codec.c -- 2.41.0

6 36

[PATCH v7 0/5] ASoC: makes CPU/Codec channel connection map more generic
by Kuninori Morimoto 14 Mar '24

14 Mar '24

Hi Mark Cc Bard, Pierre-Louis, Jerome, DT-ML This is v7 patch-set. Current ASoC is supporting CPU/Codec = N:M (N < M) connection by using ch_map idea. This patch-set expands it that all connection uses this idea, and no longer N < M limit [1][2]. Link: https://lore.kernel.org/r/87fs6wuszr.wl-kuninori.morimoto.gx@renesas.com [1] Link: https://lore.kernel.org/r/878r7yqeo4.wl-kuninori.morimoto.gx@renesas.com [2] ASoC core code ([PATCH 1/5]) is same as v6 and it was tested by Pierre-Louis, and Jerome. Big change on v7 is basically for Audio-Graph-Card2. v6 -> v7 - use "endpoint" for N:M connection instead of ch-map-idx on Audio-Graph-Card2 v5 -> v6 - tidyup some warnings - rename "ch-map-idx" -> "channel-map-index" - Update "channel-map-index" description - add Tested-by from Pierre-Louis / Jerome v4 -> v5 - use cpu/codec index on ch_maps - separate card2 sample DT patch into prepare and new feature - ch-maps -> ch-map-idx on DT v3 -> v4 - add Jerome on To - add "description" on "ch-maps" v2 -> v3 - tidyup comment - use more clear connection image on DT - "ch_maps" -> "ch-maps" on DT - Add DT maintainer on "To:" for all patches v1 -> v2 - makes CPU/Codec connection relation clear on comment/sample - fixup type "connction" -> "connection" - makes error message clear Kuninori Morimoto (5): ASoC: makes CPU/Codec channel connection map more generic ASoC: audio-graph-card2: use better image for Multi connection ASoC: audio-graph-card2: add CPU:Codec = N:M support ASoC: audio-graph-card2-custom-sample: Add connection image ASoC: audio-graph-card2-custom-sample: add CPU/Codec = N:M sample include/sound/soc.h | 56 ++- .../audio-graph-card2-custom-sample.dtsi | 380 ++++++++++++++++-- sound/soc/generic/audio-graph-card2.c | 277 ++++++++++--- sound/soc/intel/boards/sof_sdw.c | 28 +- sound/soc/soc-core.c | 95 ++++- sound/soc/soc-dapm.c | 45 +-- sound/soc/soc-pcm.c | 44 +- 7 files changed, 754 insertions(+), 171 deletions(-) -- 2.25.1

3 15

[PATCH v3] powerpc: macio: Make remove callback of macio driver void returned
by Dawei Li 13 Mar '24

13 Mar '24

Commit fc7a6209d571 ("bus: Make remove callback return void") forces bus_type::remove be void-returned, it doesn't make much sense for any bus based driver implementing remove callbalk to return non-void to its caller. This change is for macio bus based drivers. Signed-off-by: Dawei Li <set_pte_at(a)outlook.com> --- v2 -> v3 - Rebased on latest powerpc/next. - cc' to relevant subsysem lists. v1 -> v2 - Revert unneeded changes. - Rebased on latest powerpc/next. v1 - https://lore.kernel.org/all/TYCP286MB2323FCDC7ECD87F8D97CB74BCA189@TYCP286M… --- arch/powerpc/include/asm/macio.h | 2 +- drivers/ata/pata_macio.c | 4 +--- drivers/macintosh/rack-meter.c | 4 +--- drivers/net/ethernet/apple/bmac.c | 4 +--- drivers/net/ethernet/apple/mace.c | 4 +--- drivers/net/wireless/intersil/orinoco/airport.c | 4 +--- drivers/scsi/mac53c94.c | 5 +---- drivers/scsi/mesh.c | 5 +---- drivers/tty/serial/pmac_zilog.c | 7 ++----- sound/aoa/soundbus/i2sbus/core.c | 4 +--- 10 files changed, 11 insertions(+), 32 deletions(-) diff --git a/arch/powerpc/include/asm/macio.h b/arch/powerpc/include/asm/macio.h index ff5fd82d9ff0..cb9c386dacf8 100644 --- a/arch/powerpc/include/asm/macio.h +++ b/arch/powerpc/include/asm/macio.h @@ -125,7 +125,7 @@ static inline struct pci_dev *macio_get_pci_dev(struct macio_dev *mdev) struct macio_driver { int (*probe)(struct macio_dev* dev, const struct of_device_id *match); - int (*remove)(struct macio_dev* dev); + void (*remove)(struct macio_dev *dev); int (*suspend)(struct macio_dev* dev, pm_message_t state); int (*resume)(struct macio_dev* dev); diff --git a/drivers/ata/pata_macio.c b/drivers/ata/pata_macio.c index 9ccaac9e2bc3..653106716a4b 100644 --- a/drivers/ata/pata_macio.c +++ b/drivers/ata/pata_macio.c @@ -1187,7 +1187,7 @@ static int pata_macio_attach(struct macio_dev *mdev, return rc; } -static int pata_macio_detach(struct macio_dev *mdev) +static void pata_macio_detach(struct macio_dev *mdev) { struct ata_host *host = macio_get_drvdata(mdev); struct pata_macio_priv *priv = host->private_data; @@ -1202,8 +1202,6 @@ static int pata_macio_detach(struct macio_dev *mdev) ata_host_detach(host); unlock_media_bay(priv->mdev->media_bay); - - return 0; } #ifdef CONFIG_PM_SLEEP diff --git a/drivers/macintosh/rack-meter.c b/drivers/macintosh/rack-meter.c index c28893e41a8b..f2f83c4f3af5 100644 --- a/drivers/macintosh/rack-meter.c +++ b/drivers/macintosh/rack-meter.c @@ -523,7 +523,7 @@ static int rackmeter_probe(struct macio_dev* mdev, return rc; } -static int rackmeter_remove(struct macio_dev* mdev) +static void rackmeter_remove(struct macio_dev *mdev) { struct rackmeter *rm = dev_get_drvdata(&mdev->ofdev.dev); @@ -558,8 +558,6 @@ static int rackmeter_remove(struct macio_dev* mdev) /* Get rid of me */ kfree(rm); - - return 0; } static int rackmeter_shutdown(struct macio_dev* mdev) diff --git a/drivers/net/ethernet/apple/bmac.c b/drivers/net/ethernet/apple/bmac.c index 9e653e2925f7..292b1f9cd9e7 100644 --- a/drivers/net/ethernet/apple/bmac.c +++ b/drivers/net/ethernet/apple/bmac.c @@ -1591,7 +1591,7 @@ bmac_proc_info(char *buffer, char **start, off_t offset, int length) } #endif -static int bmac_remove(struct macio_dev *mdev) +static void bmac_remove(struct macio_dev *mdev) { struct net_device *dev = macio_get_drvdata(mdev); struct bmac_data *bp = netdev_priv(dev); @@ -1609,8 +1609,6 @@ static int bmac_remove(struct macio_dev *mdev) macio_release_resources(mdev); free_netdev(dev); - - return 0; } static const struct of_device_id bmac_match[] = diff --git a/drivers/net/ethernet/apple/mace.c b/drivers/net/ethernet/apple/mace.c index fd1b008b7208..e6350971c707 100644 --- a/drivers/net/ethernet/apple/mace.c +++ b/drivers/net/ethernet/apple/mace.c @@ -272,7 +272,7 @@ static int mace_probe(struct macio_dev *mdev, const struct of_device_id *match) return rc; } -static int mace_remove(struct macio_dev *mdev) +static void mace_remove(struct macio_dev *mdev) { struct net_device *dev = macio_get_drvdata(mdev); struct mace_data *mp; @@ -296,8 +296,6 @@ static int mace_remove(struct macio_dev *mdev) free_netdev(dev); macio_release_resources(mdev); - - return 0; } static void dbdma_reset(volatile struct dbdma_regs __iomem *dma) diff --git a/drivers/net/wireless/intersil/orinoco/airport.c b/drivers/net/wireless/intersil/orinoco/airport.c index a890bfa0d5cc..276a06cdd1f5 100644 --- a/drivers/net/wireless/intersil/orinoco/airport.c +++ b/drivers/net/wireless/intersil/orinoco/airport.c @@ -85,7 +85,7 @@ airport_resume(struct macio_dev *mdev) return err; } -static int +static void airport_detach(struct macio_dev *mdev) { struct orinoco_private *priv = dev_get_drvdata(&mdev->ofdev.dev); @@ -111,8 +111,6 @@ airport_detach(struct macio_dev *mdev) macio_set_drvdata(mdev, NULL); free_orinocodev(priv); - - return 0; } static int airport_hard_reset(struct orinoco_private *priv) diff --git a/drivers/scsi/mac53c94.c b/drivers/scsi/mac53c94.c index f75928f7773e..42648ca9b8ed 100644 --- a/drivers/scsi/mac53c94.c +++ b/drivers/scsi/mac53c94.c @@ -508,7 +508,7 @@ static int mac53c94_probe(struct macio_dev *mdev, const struct of_device_id *mat return rc; } -static int mac53c94_remove(struct macio_dev *mdev) +static void mac53c94_remove(struct macio_dev *mdev) { struct fsc_state *fp = (struct fsc_state *)macio_get_drvdata(mdev); struct Scsi_Host *host = fp->host; @@ -526,11 +526,8 @@ static int mac53c94_remove(struct macio_dev *mdev) scsi_host_put(host); macio_release_resources(mdev); - - return 0; } - static struct of_device_id mac53c94_match[] = { { diff --git a/drivers/scsi/mesh.c b/drivers/scsi/mesh.c index 84b541a57b7b..cd2575b88c85 100644 --- a/drivers/scsi/mesh.c +++ b/drivers/scsi/mesh.c @@ -1986,7 +1986,7 @@ static int mesh_probe(struct macio_dev *mdev, const struct of_device_id *match) return -ENODEV; } -static int mesh_remove(struct macio_dev *mdev) +static void mesh_remove(struct macio_dev *mdev) { struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev); struct Scsi_Host *mesh_host = ms->host; @@ -2013,11 +2013,8 @@ static int mesh_remove(struct macio_dev *mdev) macio_release_resources(mdev); scsi_host_put(mesh_host); - - return 0; } - static struct of_device_id mesh_match[] = { { diff --git a/drivers/tty/serial/pmac_zilog.c b/drivers/tty/serial/pmac_zilog.c index 13668ffdb1e7..d4640479c338 100644 --- a/drivers/tty/serial/pmac_zilog.c +++ b/drivers/tty/serial/pmac_zilog.c @@ -1507,12 +1507,12 @@ static int pmz_attach(struct macio_dev *mdev, const struct of_device_id *match) * That one should not be called, macio isn't really a hotswap device, * we don't expect one of those serial ports to go away... */ -static int pmz_detach(struct macio_dev *mdev) +static void pmz_detach(struct macio_dev *mdev) { struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev); if (!uap) - return -ENODEV; + return; uart_remove_one_port(&pmz_uart_reg, &uap->port); @@ -1523,11 +1523,8 @@ static int pmz_detach(struct macio_dev *mdev) dev_set_drvdata(&mdev->ofdev.dev, NULL); uap->dev = NULL; uap->port.dev = NULL; - - return 0; } - static int pmz_suspend(struct macio_dev *mdev, pm_message_t pm_state) { struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev); diff --git a/sound/aoa/soundbus/i2sbus/core.c b/sound/aoa/soundbus/i2sbus/core.c index 51ed2f34b276..35f39727994d 100644 --- a/sound/aoa/soundbus/i2sbus/core.c +++ b/sound/aoa/soundbus/i2sbus/core.c @@ -364,15 +364,13 @@ static int i2sbus_probe(struct macio_dev* dev, const struct of_device_id *match) return 0; } -static int i2sbus_remove(struct macio_dev* dev) +static void i2sbus_remove(struct macio_dev *dev) { struct i2sbus_control *control = dev_get_drvdata(&dev->ofdev.dev); struct i2sbus_dev *i2sdev, *tmp; list_for_each_entry_safe(i2sdev, tmp, &control->list, item) soundbus_remove_one(&i2sdev->sound); - - return 0; } #ifdef CONFIG_PM -- 2.25.1

6 6

[PATCH V4 00/13] soundwire/SOF: add SoundWire Interface support for AMD SOF stack
by Vijendar Mukunda 13 Mar '24

13 Mar '24

This patch series is to redesign existing platform device creation logic for SoundWire managers and Implement generic functions for SoundWire manager probe, start and exit sequence which are common for both Legacy (NO DSP enabled) and SOF stack, and add SoundWire Interface support for AMD SOF stack (ACP 6.3 based platform). Below patch series is reviewed in https://github.com/thesofproject/linux/pull/4699 Changes since V1: - add new commit to update license for amd soundwire manager driver files. - wrap the commit message with in 75 characters. - add amd tag in commit title for soundwire patches Changes since V2: - drop "drivers" tag from commit title for SoundWire patches. changes since v3: - update copyright year - add missing blank line in sdw_amd.h file This patch series has dependencies. "soundwire: amd: refactor amd soundwire manager device node creation" patch has dependency on below patch. "ASoC/soundwire: implement generic api for scanning amd soundwire controller" Similarly SOF patches has dependency on Soundwire tree patches. This patch series has to be reviewed and merged in one go. Vijendar Mukunda (13): ASoC/soundwire: implement generic api for scanning amd soundwire controller soundwire: amd: update license soundwire: amd: refactor amd soundwire manager device node creation soundwire: amd: implement function to extract slave information soundwire: amd: refactor soundwire pads enable soundwire: amd: refactor register mask structure ASoC: SOF: amd: add code for invoking soundwire manager helper functions ASoC: SOF: amd: add interrupt handling for SoundWire manager devices ASoC: SOF: amd: Add Soundwire DAI configuration support for AMD platforms ASoC: SOF: amd: add machine select logic for soundwire based platforms ASoC: SOF: amd: update descriptor fields for acp6.3 based platform ASoC: SOF: amd: select soundwire dependency flag for acp6.3 based platform ASoC: SOF: amd: refactor acp driver pm ops drivers/soundwire/Makefile | 2 +- drivers/soundwire/amd_init.c | 235 +++++++++++++++++++++++++++++ drivers/soundwire/amd_init.h | 13 ++ drivers/soundwire/amd_manager.c | 47 ++---- drivers/soundwire/amd_manager.h | 16 +- include/linux/soundwire/sdw_amd.h | 83 ++++++++-- include/sound/sof/dai-amd.h | 7 + include/sound/sof/dai.h | 2 + include/uapi/sound/sof/tokens.h | 4 + sound/soc/amd/acp/Kconfig | 7 + sound/soc/amd/acp/Makefile | 2 + sound/soc/amd/acp/amd-sdw-acpi.c | 62 ++++++++ sound/soc/sof/amd/Kconfig | 18 +++ sound/soc/sof/amd/acp-common.c | 65 +++++++- sound/soc/sof/amd/acp-dsp-offset.h | 10 ++ sound/soc/sof/amd/acp.c | 202 ++++++++++++++++++++++++- sound/soc/sof/amd/acp.h | 26 +++- sound/soc/sof/amd/pci-acp63.c | 7 + sound/soc/sof/ipc3-pcm.c | 25 +++ sound/soc/sof/ipc3-topology.c | 40 +++++ sound/soc/sof/sof-audio.h | 1 + sound/soc/sof/topology.c | 5 + 22 files changed, 805 insertions(+), 74 deletions(-) create mode 100644 drivers/soundwire/amd_init.c create mode 100644 drivers/soundwire/amd_init.h create mode 100644 sound/soc/amd/acp/amd-sdw-acpi.c -- 2.34.1

4 25