October 2024 - Alsa-devel - mailman.alsa-project.org

[PATCH v2 0/2] Updates for Atmel SSC DAI
by Andrei Simion 01 Oct '24

01 Oct '24

This patch set includes two updates for the Atmel SSC DAI driver: - Address the limitation with the S24_LE format. - Add stream names for DPCM and future use-cases. Codrin Ciubotariu (2): ASoC: atmel: atmel_ssc_dai: Add stream names ASoC: atmel: atmel_ssc_dai: Drop S24_LE support due to single channel limitation sound/soc/atmel/atmel_ssc_dai.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) base-commit: 7083504315d64199a329de322fce989e1e10f4f7 -- 2.34.1

3 4

[PATCH 0/2] Updates for mchp-spdif(tx/rx)
by Andrei Simion 01 Oct '24

01 Oct '24

This patch set includes two updates for the MCHP SPDIF RX and TX drivers. The patches remove the interface name from the stream_name, allowing the interface name and index to be set in the Device Tree (DT) using the sound-name-prefix string property. Codrin Ciubotariu (2): ASoC: atmel: mchp-spdiftx: Remove interface name from stream_name ASoC: atmel: mchp-spdifrx: Remove interface name from stream_name sound/soc/atmel/mchp-spdifrx.c | 2 +- sound/soc/atmel/mchp-spdiftx.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) base-commit: 5acd9952f95fb4b7da6d09a3be39195a80845eb6 -- 2.34.1

2 3

[PATCH 0/8] ASoC: amd: acp: refactor acp version differentiation logic
by Vijendar Mukunda 01 Oct '24

01 Oct '24

Currently different logics being used in the code for acp version differentiation. This patch series refactors the code to use acp pci revision id for handling acp version specific code. Vijendar Mukunda (8): ASoC: amd: acp: simplify platform conditional checks code ASoC: amd: acp: use acp_rev for platform specific conditional checks ASoC: amd: acp: use acp pci revision id for platform differntiation ASoC: amd: acp: store acp pci rev id in platform driver private structure ASoC: amd: acp: pass acp pci revision id as platform data ASoC: amd: acp: remove unused variable from acp_card_drvdata structure ASoC: amd: acp: replace adata->platform conditional check ASoC: amd: acp: remove unused variable from acp platform driver sound/soc/amd/acp/acp-i2s.c | 38 +++++++++++++-------------- sound/soc/amd/acp/acp-legacy-common.c | 24 ++++++++--------- sound/soc/amd/acp/acp-legacy-mach.c | 8 +++--- sound/soc/amd/acp/acp-mach-common.c | 38 +++++++++++++++++++-------- sound/soc/amd/acp/acp-mach.h | 12 +++------ sound/soc/amd/acp/acp-pci.c | 7 +---- sound/soc/amd/acp/acp-pdm.c | 2 +- sound/soc/amd/acp/acp-platform.c | 14 +++++----- sound/soc/amd/acp/acp-rembrandt.c | 4 +-- sound/soc/amd/acp/acp-renoir.c | 4 +-- sound/soc/amd/acp/acp-sof-mach.c | 6 ++--- sound/soc/amd/acp/acp63.c | 4 +-- sound/soc/amd/acp/acp70.c | 14 ++++------ sound/soc/amd/acp/acp_common.h | 19 ++++++++++++++ sound/soc/amd/acp/amd.h | 9 ++----- 15 files changed, 108 insertions(+), 95 deletions(-) create mode 100644 sound/soc/amd/acp/acp_common.h -- 2.34.1

3 10

[PATCH v28 00/32] Introduce QC USB SND audio offloading support
by Wesley Cheng 01 Oct '24

01 Oct '24

Requesting to see if we can get some Acked-By tags, and merge on usb-next. Several Qualcomm based chipsets can support USB audio offloading to a dedicated audio DSP, which can take over issuing transfers to the USB host controller. The intention is to reduce the load on the main processors in the SoC, and allow them to be placed into lower power modes. There are several parts to this design: 1. Adding ASoC binding layer 2. Create a USB backend for Q6DSP 3. Introduce XHCI interrupter support 4. Create vendor ops for the USB SND driver USB | ASoC -------------------------------------------------------------------- | _________________________ | |sm8250 platform card | | |_________________________| | | | | ___V____ ____V____ | |Q6USB | |Q6AFE | | |"codec" | |"cpu" | | |________| |_________| | ^ ^ ^ | | |________| | ___V____ | | |SOC-USB | | ________ ________ | | | |USB SND |<--->|QC offld|<------------>|________| | |(card.c)| | |<---------- | |________| |________|___ | | | ^ ^ | | | ____________V_________ | | | | | |APR/GLINK | __ V_______________V_____ | | | |______________________| |USB SND (endpoint.c) | | | | ^ |_________________________| | | | | ^ | | | ___________V___________ | | | |->|audio DSP | ___________V_____________ | | |_______________________| |XHCI HCD |<- | |_________________________| | Adding ASoC binding layer ========================= soc-usb: Intention is to treat a USB port similar to a headphone jack. The port is always present on the device, but cable/pin status can be enabled/disabled. Expose mechanisms for USB backend ASoC drivers to communicate with USB SND. Create a USB backend for Q6DSP ============================== q6usb: Basic backend driver that will be responsible for maintaining the resources needed to initiate a playback stream using the Q6DSP. Will be the entity that checks to make sure the connected USB audio device supports the requested PCM format. If it does not, the PCM open call will fail, and userspace ALSA can take action accordingly. Introduce XHCI interrupter support ================================== XHCI HCD supports multiple interrupters, which allows for events to be routed to different event rings. This is determined by "Interrupter Target" field specified in Section "6.4.1.1 Normal TRB" of the XHCI specification. Events in the offloading case will be routed to an event ring that is assigned to the audio DSP. Create vendor ops for the USB SND driver ======================================== qc_audio_offload: This particular driver has several components associated with it: - QMI stream request handler - XHCI interrupter and resource management - audio DSP memory management When the audio DSP wants to enable a playback stream, the request is first received by the ASoC platform sound card. Depending on the selected route, ASoC will bring up the individual DAIs in the path. The Q6USB backend DAI will send an AFE port start command (with enabling the USB playback path), and the audio DSP will handle the request accordingly. Part of the AFE USB port start handling will have an exchange of control messages using the QMI protocol. The qc_audio_offload driver will populate the buffer information: - Event ring base address - EP transfer ring base address and pass it along to the audio DSP. All endpoint management will now be handed over to the DSP, and the main processor is not involved in transfers. Overall, implementing this feature will still expose separate sound card and PCM devices for both the platform card and USB audio device: 0 [SM8250MTPWCD938]: sm8250 - SM8250-MTP-WCD9380-WSA8810-VA-D SM8250-MTP-WCD9380-WSA8810-VA-DMIC 1 [Audio ]: USB-Audio - USB Audio Generic USB Audio at usb-xhci-hcd.1.auto-1.4, high speed This is to ensure that userspace ALSA entities can decide which route to take when executing the audio playback. In the above, if card#1 is selected, then USB audio data will take the legacy path over the USB PCM drivers, etc... The current limitation is that the latest USB audio device that is identified will be automatically selected by the Q6USB BE DAI for offloading. Future patches can be added to possibly add for more flexibility, but until the userpace applications can be better defined, having these mechanisms will complicate the overall implementation. USB offload Kcontrols ===================== Part of the vendor offload package will have a mixer driver associated with it (mixer_usb_offload.c). This entity will be responsible for coordinating with SOC USB and the Q6USB backend DAI to fetch information about the sound card and PCM device indices associated with the offload path. The logic is done based on the current implementation of how paths are controlled within the QC ASoC implementation. QC ASoC Q6Routing ----------------- Within the Q6 ASOC design, the registered ASoC platform card will expose a set of kcontrols for enabling the BE DAI links to the FE DAI link. For example: tinymix -D 0 contents Number of controls: 1033 ctl type num name value ... 1025 BOOL 1 USB Mixer MultiMedia1 Off 1026 BOOL 1 USB Mixer MultiMedia2 Off 1027 BOOL 1 USB Mixer MultiMedia3 Off 1028 BOOL 1 USB Mixer MultiMedia4 Off 1029 BOOL 1 USB Mixer MultiMedia5 Off 1030 BOOL 1 USB Mixer MultiMedia6 Off 1031 BOOL 1 USB Mixer MultiMedia7 Off 1032 BOOL 1 USB Mixer MultiMedia8 Off Each of these kcontrols will enable the USB BE DAI link (q6usb) to be connected to a FE DAI link (q6asm). Since each of these controls are DAPM widgets, when it is enabled, the DAPM widget's "connect" flag is updated accordingly. USB Offload Mapping ------------------- Based on the Q6routing, the USB BE DAI link can determine which sound card and PCM device is enabled for offloading. Fetching the ASoC platform sound card's information is fairly straightforward, and the bulk of the work goes to finding the corresponding PCM device index. As mentioned above, the USB BE DAI can traverse the DAPM widgets to find the DAPM path that is related to the control for the "USB Mixer." Based on which "USB Mixer" is enabled, it can find the corresponding DAPM widget associated w/ the FE DAI link (Multimedia*). From there it can find the PCM device created for the Multimedia* stream. Only one BE DAI link can be enabled per FE DAI. For example, if the HDMI path is enabled for Multimedia1, the USB Mixer will be disabled and switched over. Examples of kcontrol -------------------- tinymix -D 0 contents Number of controls: 1033 ctl type num name ... 1025 BOOL 1 USB Mixer MultiMedia1 Off 1026 BOOL 1 USB Mixer MultiMedia2 On 1027 BOOL 1 USB Mixer MultiMedia3 Off 1028 BOOL 1 USB Mixer MultiMedia4 Off 1029 BOOL 1 USB Mixer MultiMedia5 Off 1030 BOOL 1 USB Mixer MultiMedia6 Off 1031 BOOL 1 USB Mixer MultiMedia7 Off 1032 BOOL 1 USB Mixer MultiMedia8 Off tinymix -D 2 contents Number of controls: 7 ctl type num name value 0 INT 2 Playback Channel Map 0, 0 (range 0->36) 1 BOOL 2 MDR-1ADAC Playback Switch On, On 2 BOOL 1 MDR-1ADAC Playback Switch On 3 INT 2 MDR-1ADAC Playback Volume 127, 127 (range 0->127) 4 INT 1 MDR-1ADAC Playback Volume 127 (range 0->127) 5 BOOL 1 Sony Internal Clock Validity On 6 INT 2 USB Offload Playback Route PCM#0 0, 1 (range -1->255) The example highlights that the userspace/application can utilize the offload path for the USB device on card#0 PCM device#1. When dealing with multiple USB audio devices, only the latest USB device identified is going to be selected for offload capable. tinymix -D 1 contents Number of controls: 9 ctl type num name value 0 INT 2 Capture Channel Map 0, 0 (range 0->36) 1 INT 2 Playback Channel Map 0, 0 (range 0->36) 2 BOOL 1 Headset Capture Switch On 3 INT 1 Headset Capture Volume 1 (range 0->4) 4 BOOL 1 Sidetone Playback Switch On 5 INT 1 Sidetone Playback Volume 4096 (range 0->8192) 6 BOOL 1 Headset Playback Switch On 7 INT 2 Headset Playback Volume 20, 20 (range 0->24) 8 INT 2 USB Offload Playback Route PCM#0 -1, -1 (range -1->255) "-1, -1" shows that this device has no route to the offload path. This feature was validated using: - tinymix: set/enable the multimedia path to route to USB backend - tinyplay: issue playback on platform card Changelog -------------------------------------------- Changes in v28: - Updated comments and commit log in the stop endpoint sync patch. Clarified that the default stop endpoint completion routine won't fully run as expected since it has a completion associated w/ the command. - Added a null check for sb->xhci within xhci_sideband_create_interrupter(). This is to just ensure that caller has registered sideband before calling create interrupter. Changes in v27: - Added some comments and notes about the offload design. Enforcing the q6routing to only allow one USB mixer (PCM device) to be enabled at a time. - Modified SND_JACK_USB notifications for all USB audio offloadable devices plugged in - Rebased on latest XHCI secondary interrupter IMOD changes upstream. Modified the change in this series to allow for XHCI sideband to set the IMOD for sideband clients. - Updated documentation on how USB SND kcontrols are involved in the overall design. - Remove mutex locking from suspend/resume platform ops, as USB core ensures that the interface and device are in the RPM_ACTIVE state while disconnect is handled. Changes in v26: - Cleaned up drivers based on errors from checkpatch - Fixed several typos using codespell - Removed any vendor specific notation from USB SND offload mixer patch Changes in v25: - Cleanups on typos mentioned within the xHCI layers - Modified the xHCI interrupter search if clients specify interrupter index - Moved mixer_usb_offload into its own module, so that other vendor offload USB modules can utilize it also. - Added support for USB audio devices that may have multiple PCM streams, as previous implementation only assumed a single PCM device. SOC USB will be able to handle an array of PCM indexes supported by the USB audio device. - Added some additional checks in the QC USB offload driver to check that device has at least one playback stream before allowing to bind - Reordered DT bindings to fix the error found by Rob's bot. The patch that added USB_RX was after the example was updated. - Updated comments within SOC USB to clarify terminology and to keep it consistent - Added SND_USB_JACK type for notifying of USB device audio connections Changes in v24: - Simplified the kcontrols involved in determining how to utilize the offload path. - There is one kcontrol registered to each USB audio device that will output which card/pcm device it is mapped to for the offload route. - Removed kcontrols to track offload status and device selection. - Default to last USB audio device plugged in as offload capable. - kcontrol will reside on USB SND device. - Reworked the tracking of connected USB devices from the Q6USB BE DAI link. Previously, it was convoluted by doing it over an array, but moved to using a list made it much simpler. Logic is still unchanged in that the last USB headset plugged in will be selected for offloading. - Updated the USB SOC RST documentation accordingly with new kcontrol updates. - Added logic to fetch mapped ASoC card and pcm device index that the offload path is mapped to for the USB SND kcontrol (for offload route). - Re-ordered series to hopefully make reviews more readable by combining patches based on the layer modified (ie QC ASoC, ASoC, USB sound, and USB XHCI). Changes in v23: - Added MODULE_DESCRIPTION() fields to drivers that needed it. Changes in v22: - Removed components tag for the ASoC platform card, as the USB SND kcontrol for notifying userspace of offload capable card achieves similar results. - Due to the above, had to remove the review-by tag for the RST documentation, as changes were made to remove the components tag section. - Took in feedback to make the SOC USB add/remove ports void. - Fixed an issue w/ the USB SND kcontrol management for devices that have multi UAC interfaces. (would attempt to create the kcontrol more than once) - Modified SOC USB card and PCM index select to be based off the num_supported streams that is specified by the USB BE DAI. - Modified comments on selecting the latest USB headset for offloading. Changes in v21: - Added an offload jack disable path from the ASoC platform driver and SOC USB. - Refactored some of the existing SOC USB context look up APIs and created some new helpers to search for the USB context. - Renamed snd_soc_usb_find_format to snd_soc_usb_find_supported_format - Removed some XHCI sideband calls that would allow clients to actually enable the IRQ line associated w/ the secondary interrupter. This is removed because there are other dependencies that are required for that to happen, which are not covered as part of this series, and to avoid confusion. - Due to the above, removed the need to export IMOD setting, and enable/disable interrupter APIs. Changes in v20: - Fixed up some formatting changes pointed out in the usb.rst - Added SB null check during XHCI sideband unregister in case caller passes improper argument (xhci_sideband_unregister()) Changes in v19: - Rebased to usb-next to account for some new changes in dependent drivers. Changes in v18: - Rebased to usb-next, which merged in part of the series. Removed these patches. - Reworked Kconfigs for the ASoC USB related components from QCOM Q6DSP drivers to keep dependencies in place for SoC USB and USB SND. - Removed the repurposing of the stop ep sync API into existing XHCI operations. This will be solely used by the XHCI sideband for now. Changes in v17: - Fixed an issue where one patch was squashed into another. - Re-added some kconfig checks for helpers exposed in USB SND for the soc usb driver, after running different kconfigs. Changes in v16: - Modified some code layer dependencies so that soc usb can be split as a separate module. - Split the kcontrols from ASoC QCOM common layer into a separate driver - Reworked SOC USB kcontrols for controlling card + pcm offload routing and status so that there are individual controls for card and pcm devices. - Added a kcontrol remove API in SOC USB to remove the controls on the fly. This required to add some kcontrol management to SOC USB. - Removed the disconnect work and workqueue for the QC USB offload as it is not required, since QMI interface driver ensures events are handled in its own WQ. Changes in v15: - Removed some already merged XHCI changes - Separated SOC USB driver from being always compiled into SOC core. Now configurable from kconfig. - Fixed up ASoC kcontrol naming to fit guidelines. - Removed some unnecessary dummy ifdefs. - Moved usb snd offload capable kcontrol to be initialized by the platform offloading driver. Changes in v14: - Cleaned up some USB SND related feedback: - Renamed SNDUSB OFFLD playback available --> USB offload capable card - Fixed locking while checking if stream is in use - Replaced some mutex pairs with guard(mutex) Changes in v13: - Pulled in secondary/primary interrupter rework from Mathias from: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/drivers… - Did some cleanup and commit message updates, and tested on current code base. - Added mutex locking to xhci sideband to help prevent any race conditions, esp. for when accessing shared references. - Addressed concerns from Hillf about gfp_flags and locking used in qc_usb_audio_offload. - Rebased onto usb-next Changes in v12: - Updated copyright year to 2024. Happy new years! - Fixed newline format on mixer offload driver. Changes in v11: - Modified QMI format structures to be const Changes in v10: - Added new mixer for exposing kcontrol for sound card created by USB SND. This allows for applications to know which platform sound card has offload support. Will return the card number. - Broke down and cleaned up some functions/APIs within qc_audio_offload driver. - Exported xhci_initialize_ring_info(), and modified XHCI makefile to allow for the XHCI sideband to exist as a module. - Reworked the jack registration and moved it to the QCOM platform card driver, ie sm8250. - Added an SOC USB API to fetch a standard component tag that can be appended to the platform sound card. Added this tag to sm8250 if any USB path exists within the DT node. - Moved kcontrols that existed in the Q6USB driver, and made it a bit more generic, so that naming can be standardized across solutions. SOC USB is now responsible for creation of these kcontrols. - Added a SOC USB RST document explaining some code flows and implementation details so that other vendors can utilize the framework. - Addressed a case where USB device connection events are lost if usb offload driver (qc_audio_offload) is not probed when everything else has been initialized, ie USB SND, SOC USB and ASoC sound card. Add a rediscover device call during module init, to ensure that connection events will be propagated. - Rebased to usb-next. Changes in v9: - Fixed the dt binding check issue with regards to num-hc-interrupters. Changes in v8: - Cleaned up snd_soc_usb_find_priv_data() based on Mark's feedback. Removed some of the duplicate looping code that was present on previous patches. Also renamed the API. - Integrated Mathias' suggestions on his new sideband changes: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… - Addressed some of Mathias' fixme tags, such as: - Resetting transfer ring dequeue/enqueue pointers - Issuing stop endpoint command during ep removal - Reset ERDP properly to first segment ring during interrupter removal. (this is currently just being cleared to 0, but should be pointing to a valid segment if controller is still running. Changes in v7: - Fixed dt check error for q6usb bindings - Updated q6usb property from qcom,usb-audio-intr-num --> qcom,usb-audio-intr-idx - Removed separate DWC3 HC interrupters num property, and place limits to XHCI one. - Modified xhci_ring_to_sgtable() to use assigned IOVA/DMA address to fetch pages, as it is not ensured event ring allocated is always done in the vmalloc range. Changes in v6: - Fixed limits and description on several DT bindings (XHCI and Q6USB) - Fixed patch subjects to follow other ALSA/ASoC notations. USB SND - Addressed devices which expose multiple audio (UAC) interfaces. These devices will create a single USB sound card with multiple audio streams, and receive multiple interface probe routines. QC offload was not properly considering cases with multiple probe calls. - Renamed offload module name and kconfig to fit within the SND domain. - Renamed attach/detach endpoint API to keep the hw_params notation. Changes in v5: - Removed some unnecessary files that were included - Fixed some typos mentioned - Addressed dt-binding issues and added hc-interrupters definition to usb-xhci.yaml XHCI: - Moved secondary skip events API to xhci-ring and updated implementation - Utilized existing XHCI APIs, such as inc_deq and xhci_update_erst_dequeue() USB SND - Renamed and reworked the APIs in "sound: usb: Export USB SND APIs for modules" patch to include suggestions to utilize snd_usb_hw_params/free and to avoid generic naming. - Added a resume_cb() op for completion sake. - Addressed some locking concerns with regards to when registering for platform hooks. - Added routine to disconnect all offloaded devices during module unbind. ASoC - Replaced individual PCM parameter arguments in snd_soc_usb_connect() with new snd_soc_usb_device structure to pass along PCM info. - Modified snd_jack set report to notify HEADPHONE event, as we do not support record path. Changes in v4: - Rebased to xhci/for-usb-next - Addressed some dt-bindings comments XHCI: - Pulled in latest changes from Mathias' feature_interrupters branch: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… - Fixed commit text and signage for the XHCI sideband/interrupter related changes - Added some logic to address the FIXME tags mentioned throughout the commits, such as handling multi segment rings and building the SGT, locking concerns, and ep cleanup operations. - Removed some fixme tags for conditions that may not be needed/addressed. - Repurposed the new endpoint stop sync API to be utilized in other places. - Fixed potential compile issue if XHCI sideband config is not defined. ASoC: - Added sound jack control into the Q6USB driver. Allows for userspsace to know when an offload capable device is connected. USB SND: - Avoided exporting _snd_pcm_hw_param_set based on Takashi's recommendation. - Split USB QMI packet header definitions into a separate commit. This is used to properly allow the QMI interface driver to parse and route QMI packets accordingly - Added a "depends on" entry when enabling QC audio offload to avoid compile time issues. Changes in v3: - Changed prefix from RFC to PATCH - Rebased entire series to usb-next - Updated copyright years XHCI: - Rebased changes on top of XHCI changes merged into usb-next, and only added changes that were still under discussion. - Added change to read in the "num-hc-interrupters" device property. ASoC: - qusb6 USB backend - Incorporated suggestions to fetch iommu information with existing APIs - Added two new sound kcontrols to fetch offload status and offload device selection. - offload status - will return the card and pcm device in use tinymix -D 0 get 1 --> 1, 0 (offload in progress on card#1 pcm#0) - device selection - set the card and pcm device to enable offload on. Ex.: tinymix -D 0 set 1 2 0 --> sets offload on card#2 pcm#0 (this should be the USB card) USB SND: - Fixed up some locking related concerns for registering platform ops. - Moved callbacks under the register_mutex, so that - Modified APIs to properly pass more information about the USB SND device, so that the Q6USB backend can build a device list/map, in order to monitor offload status and device selection. Changes in v2: XHCI: - Replaced XHCI and HCD changes with Mathias' XHCI interrupter changes in his tree: https://git.kernel.org/pub/scm/linux/kernel/git/mnyman/xhci.git/log/?h=feat… Adjustments made to Mathias' changes: - Created xhci-intr.h to export/expose interrupter APIs versus exposing xhci.h. Moved dependent structures to this file as well. (so clients can parse out information from "struct xhci_interrupter") - Added some basic locking when requesting interrupters. - Fixed up some sanity checks. - Removed clearing of the ERSTBA during freeing of the interrupter. (pending issue where SMMU fault occurs if DMA addr returned is 64b - TODO) - Clean up pending events in the XHCI secondary interrupter. While testing USB bus suspend, it was seen that on bus resume, the xHCI HC would run into a command timeout. - Added offloading APIs to xHCI to fetch transfer and event ring information. ASoC: - Modified soc-usb to allow for multiple USB port additions. For this to work, the USB offload driver has to have a reference to the USB backend by adding a "usb-soc-be" DT entry to the device saved into XHCI sysdev. - Created separate dt-bindings for defining USB_RX port. - Increased APR timeout to accommodate the situation where the AFE port start command could be delayed due to having to issue a USB bus resume while handling the QMI stream start command. Mathias Nyman (2): xhci: add helper to stop endpoint and wait for completion xhci: sideband: add initial api to register a sideband entity Wesley Cheng (30): usb: host: xhci: Repurpose event handler for skipping interrupter events usb: xhci: xhci-sideband: Set IMOD for xHCI sideband clients usb: host: xhci-mem: Cleanup pending secondary event ring events usb: host: xhci-mem: Allow for interrupter clients to choose specific index usb: host: xhci-plat: Set XHCI max interrupters if property is present usb: dwc3: Specify maximum number of XHCI interrupters ALSA: Add USB audio device jack type ALSA: usb-audio: Export USB SND APIs for modules ALSA: usb-audio: Check for support for requested audio format ALSA: usb-audio: Save UAC sample size information ALSA: usb-audio: Prevent starting of audio stream if in use ASoC: Add SOC USB APIs for adding an USB backend ASoC: usb: Add PCM format check API for USB backend ASoC: usb: Create SOC USB SND jack kcontrol ASoC: usb: Fetch ASoC card and pcm device information ASoC: doc: Add documentation for SOC USB ASoC: dt-bindings: qcom,q6dsp-lpass-ports: Add USB_RX port ASoC: dt-bindings: Update example for enabling USB offload on SM8250 ASoC: qcom: qdsp6: Introduce USB AFE port to q6dsp ASoC: qcom: qdsp6: q6afe: Increase APR timeout ASoC: qcom: qdsp6: Add USB backend ASoC driver for Q6 ASoC: qcom: qdsp6: Add headphone jack for offload connection status ASoC: qcom: qdsp6: Fetch USB offload mapped card and PCM device ALSA: usb-audio: Introduce USB SND platform op callbacks ALSA: usb-audio: qcom: Add USB QMI definitions ALSA: usb-audio: qcom: Introduce QC USB SND offloading support ALSA: usb-audio: qcom: Don't allow USB offload path if PCM device is in use ALSA: usb-audio: Add USB offload route kcontrol ALSA: usb-audio: Allow for rediscovery of connected USB SND devices ASoC: usb: Rediscover USB SND devices on USB port add .../bindings/sound/qcom,sm8250.yaml | 15 + Documentation/sound/soc/index.rst | 1 + Documentation/sound/soc/usb.rst | 456 ++++ drivers/usb/dwc3/core.c | 12 + drivers/usb/dwc3/core.h | 2 + drivers/usb/dwc3/host.c | 3 + drivers/usb/host/Kconfig | 9 + drivers/usb/host/Makefile | 2 + drivers/usb/host/xhci-mem.c | 31 +- drivers/usb/host/xhci-plat.c | 2 + drivers/usb/host/xhci-ring.c | 54 +- drivers/usb/host/xhci-sideband.c | 425 ++++ drivers/usb/host/xhci.c | 47 +- drivers/usb/host/xhci.h | 16 +- .../sound/qcom,q6dsp-lpass-ports.h | 1 + include/linux/mod_devicetable.h | 2 +- include/linux/usb/xhci-sideband.h | 70 + include/sound/jack.h | 4 +- include/sound/q6usboffload.h | 20 + include/sound/soc-usb.h | 139 ++ include/uapi/linux/input-event-codes.h | 3 +- sound/core/jack.c | 6 +- sound/soc/Kconfig | 10 + sound/soc/Makefile | 2 + sound/soc/qcom/Kconfig | 15 + sound/soc/qcom/Makefile | 2 + sound/soc/qcom/qdsp6/Makefile | 1 + sound/soc/qcom/qdsp6/q6afe-dai.c | 60 + sound/soc/qcom/qdsp6/q6afe.c | 194 +- sound/soc/qcom/qdsp6/q6afe.h | 36 +- sound/soc/qcom/qdsp6/q6dsp-lpass-ports.c | 23 + sound/soc/qcom/qdsp6/q6dsp-lpass-ports.h | 1 + sound/soc/qcom/qdsp6/q6routing.c | 32 +- sound/soc/qcom/qdsp6/q6usb.c | 391 ++++ sound/soc/qcom/sm8250.c | 24 +- sound/soc/qcom/usb_offload_utils.c | 56 + sound/soc/qcom/usb_offload_utils.h | 30 + sound/soc/soc-usb.c | 342 +++ sound/usb/Kconfig | 25 + sound/usb/Makefile | 4 +- sound/usb/card.c | 106 + sound/usb/card.h | 17 + sound/usb/endpoint.c | 1 + sound/usb/format.c | 1 + sound/usb/helper.c | 1 + sound/usb/mixer_usb_offload.c | 102 + sound/usb/mixer_usb_offload.h | 17 + sound/usb/pcm.c | 104 +- sound/usb/pcm.h | 11 + sound/usb/qcom/Makefile | 2 + sound/usb/qcom/qc_audio_offload.c | 1968 +++++++++++++++++ sound/usb/qcom/usb_audio_qmi_v01.c | 863 ++++++++ sound/usb/qcom/usb_audio_qmi_v01.h | 164 ++ 53 files changed, 5870 insertions(+), 55 deletions(-) create mode 100644 Documentation/sound/soc/usb.rst create mode 100644 drivers/usb/host/xhci-sideband.c create mode 100644 include/linux/usb/xhci-sideband.h create mode 100644 include/sound/q6usboffload.h create mode 100644 include/sound/soc-usb.h create mode 100644 sound/soc/qcom/qdsp6/q6usb.c create mode 100644 sound/soc/qcom/usb_offload_utils.c create mode 100644 sound/soc/qcom/usb_offload_utils.h create mode 100644 sound/soc/soc-usb.c create mode 100644 sound/usb/mixer_usb_offload.c create mode 100644 sound/usb/mixer_usb_offload.h create mode 100644 sound/usb/qcom/Makefile create mode 100644 sound/usb/qcom/qc_audio_offload.c create mode 100644 sound/usb/qcom/usb_audio_qmi_v01.c create mode 100644 sound/usb/qcom/usb_audio_qmi_v01.h

3 41

[PATCH] ASoC: fsl_sai: Enable 'FIFO continue on error' FCONT bit
by Shengjiu Wang 01 Oct '24

01 Oct '24

FCONT=1 means On FIFO error, the SAI will continue from the same word that caused the FIFO error to set after the FIFO warning flag has been cleared. Set FCONT bit in control register to avoid the channel swap issue after SAI xrun. Signed-off-by: Shengjiu Wang <shengjiu.wang(a)nxp.com> --- sound/soc/fsl/fsl_sai.c | 5 ++++- sound/soc/fsl/fsl_sai.h | 1 + 2 files changed, 5 insertions(+), 1 deletion(-) diff --git a/sound/soc/fsl/fsl_sai.c b/sound/soc/fsl/fsl_sai.c index ab58a4461073..634168d2bb6e 100644 --- a/sound/soc/fsl/fsl_sai.c +++ b/sound/soc/fsl/fsl_sai.c @@ -613,6 +613,9 @@ static int fsl_sai_hw_params(struct snd_pcm_substream *substream, val_cr4 |= FSL_SAI_CR4_FRSZ(slots); + /* Set to avoid channel swap */ + val_cr4 |= FSL_SAI_CR4_FCONT; + /* Set to output mode to avoid tri-stated data pins */ if (tx) val_cr4 |= FSL_SAI_CR4_CHMOD; @@ -699,7 +702,7 @@ static int fsl_sai_hw_params(struct snd_pcm_substream *substream, regmap_update_bits(sai->regmap, FSL_SAI_xCR4(tx, ofs), FSL_SAI_CR4_SYWD_MASK | FSL_SAI_CR4_FRSZ_MASK | - FSL_SAI_CR4_CHMOD_MASK, + FSL_SAI_CR4_CHMOD_MASK | FSL_SAI_CR4_FCONT_MASK, val_cr4); regmap_update_bits(sai->regmap, FSL_SAI_xCR5(tx, ofs), FSL_SAI_CR5_WNW_MASK | FSL_SAI_CR5_W0W_MASK | diff --git a/sound/soc/fsl/fsl_sai.h b/sound/soc/fsl/fsl_sai.h index dadbd16ee394..9c4d19fe22c6 100644 --- a/sound/soc/fsl/fsl_sai.h +++ b/sound/soc/fsl/fsl_sai.h @@ -137,6 +137,7 @@ /* SAI Transmit and Receive Configuration 4 Register */ +#define FSL_SAI_CR4_FCONT_MASK BIT(28) #define FSL_SAI_CR4_FCONT BIT(28) #define FSL_SAI_CR4_FCOMB_SHIFT BIT(26) #define FSL_SAI_CR4_FCOMB_SOFT BIT(27) -- 2.34.1

2 1

[PATCH alsa-ucm-conf 1/2] sof-soundwire: Change mapped control names to make them unique
by Maciej Strozek 01 Oct '24

01 Oct '24

Both 'Speaker Digital' and 'cs42l43 PDM2' names were found as substrings in other alsa controls, confusing the MixerElems paths. Make them unique to avoid errors for hardware mutes. Also add 'Capture' string into microphone controls to make them work properly. Fixes: e87dde51d689 ("sof-soundwire: Add basic support for cs42l43") Fixes: e4277a204cd6 ("sof-soundwire: Add support for cs42l43/cs35l56 bridge configuration") Signed-off-by: Maciej Strozek <mstrozek(a)opensource.cirrus.com> --- ucm2/codecs/cs42l43/init.conf | 4 ++-- ucm2/sof-soundwire/cs35l56-bridge.conf | 6 +++--- ucm2/sof-soundwire/cs42l43-dmic.conf | 2 +- 3 files changed, 6 insertions(+), 6 deletions(-) diff --git a/ucm2/codecs/cs42l43/init.conf b/ucm2/codecs/cs42l43/init.conf index 10a6e1f..cf61833 100644 --- a/ucm2/codecs/cs42l43/init.conf +++ b/ucm2/codecs/cs42l43/init.conf @@ -2,11 +2,11 @@ LibraryConfig.remap.Config { ctl.default.map { - "name='cs42l43 PDM2 Switch'" { + "name='cs42l43 Microphone Capture Switch'" { "name='cs42l43 Decimator 3 Switch'".vindex.0 0 "name='cs42l43 Decimator 4 Switch'".vindex.1 0 } - "name='cs42l43 PDM2 Volume'" { + "name='cs42l43 Microphone Capture Volume'" { "name='cs42l43 Decimator 3 Volume'".vindex.0 0 "name='cs42l43 Decimator 4 Volume'".vindex.1 0 } diff --git a/ucm2/sof-soundwire/cs35l56-bridge.conf b/ucm2/sof-soundwire/cs35l56-bridge.conf index 5435b11..7c36655 100644 --- a/ucm2/sof-soundwire/cs35l56-bridge.conf +++ b/ucm2/sof-soundwire/cs35l56-bridge.conf @@ -2,11 +2,11 @@ LibraryConfig.remap.Config { ctl.default.map { - "name='Speaker Digital Switch'" { + "name='Speaker Combined Switch'" { "name='AMPL Speaker Switch'".vindex.0 0 "name='AMPR Speaker Switch'".vindex.1 0 } - "name='Speaker Digital Volume'" { + "name='Speaker Combined Volume'" { "name='AMPL Speaker Volume'".vindex.0 0 "name='AMPR Speaker Volume'".vindex.1 0 } @@ -56,6 +56,6 @@ SectionDevice."Speaker" { PlaybackPriority 100 PlaybackPCM "hw:${CardId},0" PlaybackMixer "default:${CardId}" - PlaybackMixerElem "Speaker Digital" + PlaybackMixerElem "Speaker Combined" } } diff --git a/ucm2/sof-soundwire/cs42l43-dmic.conf b/ucm2/sof-soundwire/cs42l43-dmic.conf index d5f895d..b68a70d 100644 --- a/ucm2/sof-soundwire/cs42l43-dmic.conf +++ b/ucm2/sof-soundwire/cs42l43-dmic.conf @@ -21,6 +21,6 @@ SectionDevice."Mic" { CapturePriority 100 CapturePCM "hw:${CardId},4" CaptureMixer "default:${CardId}" - CaptureMixerElem "cs42l43 PDM2" + CaptureMixerElem "cs42l43 Microphone" } } -- 2.39.5

3 5

[PATCH v3] ASoC: rt721-sdca: Add RT721 SDCA driver
by Jack Yu 01 Oct '24

01 Oct '24

This is the initial codec driver for rt721-sdca. It's a three functions (jack,mic,amp) soundwire driver. Signed-off-by: Jack Yu <jack.yu(a)realtek.com> v2: Fix typo in mbq default registers. v3: Include soundwire common functions for Realtek. --- sound/soc/codecs/Kconfig | 7 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/rt721-sdca-sdw.c | 551 ++++++++++ sound/soc/codecs/rt721-sdca-sdw.h | 150 +++ sound/soc/codecs/rt721-sdca.c | 1547 +++++++++++++++++++++++++++++ sound/soc/codecs/rt721-sdca.h | 268 +++++ 6 files changed, 2525 insertions(+) create mode 100644 sound/soc/codecs/rt721-sdca-sdw.c create mode 100644 sound/soc/codecs/rt721-sdca-sdw.h create mode 100644 sound/soc/codecs/rt721-sdca.c create mode 100644 sound/soc/codecs/rt721-sdca.h diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 7092842480ef..74c14da4ae09 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -222,6 +222,7 @@ config SND_SOC_ALL_CODECS imply SND_SOC_RT712_SDCA_DMIC_SDW imply SND_SOC_RT715_SDW imply SND_SOC_RT715_SDCA_SDW + imply SND_SOC_RT721_SDCA_SDW imply SND_SOC_RT722_SDCA_SDW imply SND_SOC_RT1308_SDW imply SND_SOC_RT1316_SDW @@ -1743,6 +1744,12 @@ config SND_SOC_RT712_SDCA_DMIC_SDW select REGMAP_SOUNDWIRE select REGMAP_SOUNDWIRE_MBQ +config SND_SOC_RT721_SDCA_SDW + tristate "Realtek RT721 SDCA Codec - SDW" + depends on SOUNDWIRE + select REGMAP_SOUNDWIRE + select REGMAP_SOUNDWIRE_MBQ + config SND_SOC_RT722_SDCA_SDW tristate "Realtek RT722 SDCA Codec - SDW" depends on SOUNDWIRE diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 54cbc3feae32..3477c6352acc 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -259,6 +259,7 @@ snd-soc-rt712-sdca-y := rt712-sdca.o rt712-sdca-sdw.o snd-soc-rt712-sdca-dmic-y := rt712-sdca-dmic.o snd-soc-rt715-y := rt715.o rt715-sdw.o snd-soc-rt715-sdca-y := rt715-sdca.o rt715-sdca-sdw.o +snd-soc-rt721-sdca-y := rt721-sdca.o rt721-sdca-sdw.o snd-soc-rt722-sdca-y := rt722-sdca.o rt722-sdca-sdw.o snd-soc-rt9120-y := rt9120.o snd-soc-rtq9128-y := rtq9128.o @@ -662,6 +663,7 @@ obj-$(CONFIG_SND_SOC_RT712_SDCA_SDW) += snd-soc-rt712-sdca.o obj-$(CONFIG_SND_SOC_RT712_SDCA_DMIC_SDW) += snd-soc-rt712-sdca-dmic.o obj-$(CONFIG_SND_SOC_RT715) += snd-soc-rt715.o obj-$(CONFIG_SND_SOC_RT715_SDCA_SDW) += snd-soc-rt715-sdca.o +obj-$(CONFIG_SND_SOC_RT721_SDCA_SDW) += snd-soc-rt721-sdca.o obj-$(CONFIG_SND_SOC_RT722_SDCA_SDW) += snd-soc-rt722-sdca.o obj-$(CONFIG_SND_SOC_RT9120) += snd-soc-rt9120.o obj-$(CONFIG_SND_SOC_RTQ9128) += snd-soc-rtq9128.o diff --git a/sound/soc/codecs/rt721-sdca-sdw.c b/sound/soc/codecs/rt721-sdca-sdw.c new file mode 100644 index 000000000000..c0f8cccae3b2 --- /dev/null +++ b/sound/soc/codecs/rt721-sdca-sdw.c @@ -0,0 +1,551 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt721-sdca-sdw.c -- rt721 SDCA ALSA SoC audio driver +// +// Copyright(c) 2024 Realtek Semiconductor Corp. +// +// + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/mod_devicetable.h> +#include <linux/pm_runtime.h> +#include <linux/soundwire/sdw_registers.h> + +#include "rt721-sdca.h" +#include "rt721-sdca-sdw.h" +#include "rt-sdw-common.h" + +static bool rt721_sdca_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2f01 ... 0x2f0a: + case 0x2f35: + case 0x2f50: + case 0x2f51: + case 0x2f58 ... 0x2f5d: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_XUV, + RT721_SDCA_CTL_XUV, 0): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_GE49, + RT721_SDCA_CTL_SELECTED_MODE, 0): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_GE49, + RT721_SDCA_CTL_DETECTED_MODE, 0): + case SDW_SDCA_CTL(FUNC_NUM_HID, RT721_SDCA_ENT_HID01, + RT721_SDCA_CTL_HIDTX_CURRENT_OWNER, 0) ... SDW_SDCA_CTL(FUNC_NUM_HID, + RT721_SDCA_ENT_HID01, RT721_SDCA_CTL_HIDTX_MESSAGE_LENGTH, 0): + case RT721_BUF_ADDR_HID1 ... RT721_BUF_ADDR_HID2: + return true; + default: + return false; + } +} + +static bool rt721_sdca_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x2f01: + case 0x2f51: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_GE49, + RT721_SDCA_CTL_DETECTED_MODE, 0): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_XUV, + RT721_SDCA_CTL_XUV, 0): + case SDW_SDCA_CTL(FUNC_NUM_HID, RT721_SDCA_ENT_HID01, + RT721_SDCA_CTL_HIDTX_CURRENT_OWNER, 0) ... SDW_SDCA_CTL(FUNC_NUM_HID, + RT721_SDCA_ENT_HID01, RT721_SDCA_CTL_HIDTX_MESSAGE_LENGTH, 0): + case RT721_BUF_ADDR_HID1 ... RT721_BUF_ADDR_HID2: + return true; + default: + return false; + } +} + +static bool rt721_sdca_mbq_readable_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x0900007: + case 0x0a00005: + case 0x0c00005: + case 0x0d00014: + case 0x0310100: + case 0x2000001: + case 0x2000002: + case 0x2000003: + case 0x2000013: + case 0x200003c: + case 0x2000046: + case 0x5810000: + case 0x5810036: + case 0x5810037: + case 0x5810038: + case 0x5810039: + case 0x5b10018: + case 0x5b10019: + case 0x5f00045: + case 0x5f00048: + case 0x6100000: + case 0x6100005: + case 0x6100006: + case 0x610000d: + case 0x6100010: + case 0x6100011: + case 0x6100013: + case 0x6100015: + case 0x6100017: + case 0x6100025: + case 0x6100029: + case 0x610002c ... 0x610002f: + case 0x6100053 ... 0x6100055: + case 0x6100057: + case 0x610005a: + case 0x610005b: + case 0x610006a: + case 0x610006d: + case 0x6100092: + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, RT721_SDCA_CTL_FU_VOLUME, + CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, RT721_SDCA_CTL_FU_VOLUME, + CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, RT721_SDCA_CTL_FU_VOLUME, + CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, RT721_SDCA_CTL_FU_VOLUME, + CH_R): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PLATFORM_FU44, + RT721_SDCA_CTL_FU_CH_GAIN, CH_L): + case SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PLATFORM_FU44, + RT721_SDCA_CTL_FU_CH_GAIN, CH_R): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, RT721_SDCA_CTL_FU_VOLUME, + CH_01): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, RT721_SDCA_CTL_FU_VOLUME, + CH_02): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, RT721_SDCA_CTL_FU_VOLUME, + CH_03): + case SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, RT721_SDCA_CTL_FU_VOLUME, + CH_04): + case SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, RT721_SDCA_CTL_FU_VOLUME, CH_L): + case SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, RT721_SDCA_CTL_FU_VOLUME, CH_R): + return true; + default: + return false; + } +} + +static bool rt721_sdca_mbq_volatile_register(struct device *dev, unsigned int reg) +{ + switch (reg) { + case 0x0310100: + case 0x0a00005: + case 0x0c00005: + case 0x0d00014: + case 0x2000000: + case 0x200000d: + case 0x2000019: + case 0x2000020: + case 0x2000030: + case 0x2000046: + case 0x2000067: + case 0x2000084: + case 0x2000086: + case 0x5810000: + case 0x5810036: + case 0x5810037: + case 0x5810038: + case 0x5810039: + case 0x5b10018: + case 0x5b10019: + return true; + default: + return false; + } +} + +static const struct regmap_config rt721_sdca_regmap = { + .reg_bits = 32, + .val_bits = 8, + .readable_reg = rt721_sdca_readable_register, + .volatile_reg = rt721_sdca_volatile_register, + .max_register = 0x44ffffff, + .reg_defaults = rt721_sdca_reg_defaults, + .num_reg_defaults = ARRAY_SIZE(rt721_sdca_reg_defaults), + .cache_type = REGCACHE_MAPLE, + .use_single_read = true, + .use_single_write = true, +}; + +static const struct regmap_config rt721_sdca_mbq_regmap = { + .name = "sdw-mbq", + .reg_bits = 32, + .val_bits = 16, + .readable_reg = rt721_sdca_mbq_readable_register, + .volatile_reg = rt721_sdca_mbq_volatile_register, + .max_register = 0x41000312, + .reg_defaults = rt721_sdca_mbq_defaults, + .num_reg_defaults = ARRAY_SIZE(rt721_sdca_mbq_defaults), + .cache_type = REGCACHE_MAPLE, + .use_single_read = true, + .use_single_write = true, +}; + +static int rt721_sdca_update_status(struct sdw_slave *slave, + enum sdw_slave_status status) +{ + struct rt721_sdca_priv *rt721 = dev_get_drvdata(&slave->dev); + + if (status == SDW_SLAVE_UNATTACHED) + rt721->hw_init = false; + + if (status == SDW_SLAVE_ATTACHED) { + if (rt721->hs_jack) { + /* + * Due to the SCP_SDCA_INTMASK will be cleared by any reset, and then + * if the device attached again, we will need to set the setting back. + * It could avoid losing the jack detection interrupt. + * This also could sync with the cache value as the rt721_sdca_jack_init set. + */ + sdw_write_no_pm(rt721->slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_6); + sdw_write_no_pm(rt721->slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + } + } + + /* + * Perform initialization only if slave status is present and + * hw_init flag is false + */ + if (rt721->hw_init || status != SDW_SLAVE_ATTACHED) + return 0; + + /* perform I/O transfers required for Slave initialization */ + return rt721_sdca_io_init(&slave->dev, slave); +} + +static int rt721_sdca_read_prop(struct sdw_slave *slave) +{ + struct sdw_slave_prop *prop = &slave->prop; + int nval; + int i, j; + u32 bit; + unsigned long addr; + struct sdw_dpn_prop *dpn; + + sdw_slave_read_prop(slave); + prop->scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY; + prop->quirks = SDW_SLAVE_QUIRKS_INVALID_INITIAL_PARITY; + + prop->paging_support = true; + + /* + * port = 1 for headphone playback + * port = 2 for headset-mic capture + * port = 3 for speaker playback + * port = 6 for digital-mic capture + */ + prop->source_ports = BIT(6) | BIT(2); /* BITMAP: 01000100 */ + prop->sink_ports = BIT(3) | BIT(1); /* BITMAP: 00001010 */ + + nval = hweight32(prop->source_ports); + prop->src_dpn_prop = devm_kcalloc(&slave->dev, nval, + sizeof(*prop->src_dpn_prop), GFP_KERNEL); + if (!prop->src_dpn_prop) + return -ENOMEM; + + i = 0; + dpn = prop->src_dpn_prop; + addr = prop->source_ports; + for_each_set_bit(bit, &addr, 32) { + dpn[i].num = bit; + dpn[i].type = SDW_DPN_FULL; + dpn[i].simple_ch_prep_sm = true; + dpn[i].ch_prep_timeout = 10; + i++; + } + + /* do this again for sink now */ + nval = hweight32(prop->sink_ports); + prop->sink_dpn_prop = devm_kcalloc(&slave->dev, nval, + sizeof(*prop->sink_dpn_prop), GFP_KERNEL); + if (!prop->sink_dpn_prop) + return -ENOMEM; + + j = 0; + dpn = prop->sink_dpn_prop; + addr = prop->sink_ports; + for_each_set_bit(bit, &addr, 32) { + dpn[j].num = bit; + dpn[j].type = SDW_DPN_FULL; + dpn[j].simple_ch_prep_sm = true; + dpn[j].ch_prep_timeout = 10; + j++; + } + + /* set the timeout values */ + prop->clk_stop_timeout = 900; + + /* wake-up event */ + prop->wake_capable = 1; + + /* Three data lanes are supported by rt721-sdca codec */ + prop->lane_control_support = true; + + return 0; +} + +static int rt721_sdca_interrupt_callback(struct sdw_slave *slave, + struct sdw_slave_intr_status *status) +{ + struct rt721_sdca_priv *rt721 = dev_get_drvdata(&slave->dev); + int ret, stat; + int count = 0, retry = 3; + unsigned int sdca_cascade, scp_sdca_stat1, scp_sdca_stat2 = 0; + + if (cancel_delayed_work_sync(&rt721->jack_detect_work)) { + dev_warn(&slave->dev, "%s the pending delayed_work was cancelled", __func__); + /* avoid the HID owner doesn't change to device */ + if (rt721->scp_sdca_stat2) + scp_sdca_stat2 = rt721->scp_sdca_stat2; + } + + /* + * The critical section below intentionally protects a rather large piece of code. + * We don't want to allow the system suspend to disable an interrupt while we are + * processing it, which could be problematic given the quirky SoundWire interrupt + * scheme. We do want however to prevent new workqueues from being scheduled if + * the disable_irq flag was set during system suspend. + */ + mutex_lock(&rt721->disable_irq_lock); + + ret = sdw_read_no_pm(rt721->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + + rt721->scp_sdca_stat1 = ret; + ret = sdw_read_no_pm(rt721->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + + rt721->scp_sdca_stat2 = ret; + if (scp_sdca_stat2) + rt721->scp_sdca_stat2 |= scp_sdca_stat2; + do { + /* clear flag */ + ret = sdw_read_no_pm(rt721->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + if (ret & SDW_SCP_SDCA_INTMASK_SDCA_0) { + ret = sdw_update_no_pm(rt721->slave, SDW_SCP_SDCA_INT1, + SDW_SCP_SDCA_INT_SDCA_0, SDW_SCP_SDCA_INT_SDCA_0); + if (ret < 0) + goto io_error; + } else if (ret & SDW_SCP_SDCA_INTMASK_SDCA_6) { + ret = sdw_update_no_pm(rt721->slave, SDW_SCP_SDCA_INT1, + SDW_SCP_SDCA_INT_SDCA_6, SDW_SCP_SDCA_INT_SDCA_6); + if (ret < 0) + goto io_error; + } + ret = sdw_read_no_pm(rt721->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + if (ret & SDW_SCP_SDCA_INTMASK_SDCA_8) { + ret = sdw_write_no_pm(rt721->slave, SDW_SCP_SDCA_INT2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + if (ret < 0) + goto io_error; + } + + /* check if flag clear or not */ + ret = sdw_read_no_pm(rt721->slave, SDW_DP0_INT); + if (ret < 0) + goto io_error; + sdca_cascade = ret & SDW_DP0_SDCA_CASCADE; + + ret = sdw_read_no_pm(rt721->slave, SDW_SCP_SDCA_INT1); + if (ret < 0) + goto io_error; + scp_sdca_stat1 = ret & SDW_SCP_SDCA_INTMASK_SDCA_0; + + ret = sdw_read_no_pm(rt721->slave, SDW_SCP_SDCA_INT2); + if (ret < 0) + goto io_error; + scp_sdca_stat2 = ret & SDW_SCP_SDCA_INTMASK_SDCA_8; + + stat = scp_sdca_stat1 || scp_sdca_stat2 || sdca_cascade; + + count++; + } while (stat != 0 && count < retry); + + if (stat) + dev_warn(&slave->dev, + "%s scp_sdca_stat1=0x%x, scp_sdca_stat2=0x%x\n", __func__, + rt721->scp_sdca_stat1, rt721->scp_sdca_stat2); + ret = sdw_read_no_pm(rt721->slave, SDW_SCP_SDCA_INT1); + ret = sdw_read_no_pm(rt721->slave, SDW_SCP_SDCA_INT2); + + if (status->sdca_cascade && !rt721->disable_irq) + mod_delayed_work(system_power_efficient_wq, + &rt721->jack_detect_work, msecs_to_jiffies(280)); + + mutex_unlock(&rt721->disable_irq_lock); + + return 0; + +io_error: + mutex_unlock(&rt721->disable_irq_lock); + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} + +static const struct sdw_slave_ops rt721_sdca_slave_ops = { + .read_prop = rt721_sdca_read_prop, + .interrupt_callback = rt721_sdca_interrupt_callback, + .update_status = rt721_sdca_update_status, +}; + +static int rt721_sdca_sdw_probe(struct sdw_slave *slave, + const struct sdw_device_id *id) +{ + struct regmap *regmap, *mbq_regmap; + + /* Regmap Initialization */ + mbq_regmap = devm_regmap_init_sdw_mbq(slave, &rt721_sdca_mbq_regmap); + if (IS_ERR(mbq_regmap)) + return PTR_ERR(mbq_regmap); + + regmap = devm_regmap_init_sdw(slave, &rt721_sdca_regmap); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + return rt721_sdca_init(&slave->dev, regmap, mbq_regmap, slave); +} + +static int rt721_sdca_sdw_remove(struct sdw_slave *slave) +{ + struct rt721_sdca_priv *rt721 = dev_get_drvdata(&slave->dev); + + if (rt721->hw_init) { + cancel_delayed_work_sync(&rt721->jack_detect_work); + cancel_delayed_work_sync(&rt721->jack_btn_check_work); + } + + if (rt721->first_hw_init) + pm_runtime_disable(&slave->dev); + + mutex_destroy(&rt721->calibrate_mutex); + mutex_destroy(&rt721->disable_irq_lock); + + return 0; +} + +static const struct sdw_device_id rt721_sdca_id[] = { + SDW_SLAVE_ENTRY_EXT(0x025d, 0x721, 0x3, 0x1, 0), + {}, +}; +MODULE_DEVICE_TABLE(sdw, rt721_sdca_id); + +static int __maybe_unused rt721_sdca_dev_suspend(struct device *dev) +{ + struct rt721_sdca_priv *rt721 = dev_get_drvdata(dev); + + if (!rt721->hw_init) + return 0; + + cancel_delayed_work_sync(&rt721->jack_detect_work); + cancel_delayed_work_sync(&rt721->jack_btn_check_work); + + regcache_cache_only(rt721->regmap, true); + regcache_cache_only(rt721->mbq_regmap, true); + + return 0; +} + +static int __maybe_unused rt721_sdca_dev_system_suspend(struct device *dev) +{ + struct rt721_sdca_priv *rt721_sdca = dev_get_drvdata(dev); + struct sdw_slave *slave = dev_to_sdw_dev(dev); + int ret1, ret2; + + if (!rt721_sdca->hw_init) + return 0; + + /* + * prevent new interrupts from being handled after the + * deferred work completes and before the parent disables + * interrupts on the link + */ + mutex_lock(&rt721_sdca->disable_irq_lock); + rt721_sdca->disable_irq = true; + ret1 = sdw_update_no_pm(slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6, 0); + ret2 = sdw_update_no_pm(slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8, 0); + mutex_unlock(&rt721_sdca->disable_irq_lock); + + if (ret1 < 0 || ret2 < 0) { + /* log but don't prevent suspend from happening */ + dev_dbg(&slave->dev, "%s: could not disable SDCA interrupts\n:", __func__); + } + + return rt721_sdca_dev_suspend(dev); +} + +#define RT721_PROBE_TIMEOUT 5000 + +static int __maybe_unused rt721_sdca_dev_resume(struct device *dev) +{ + struct sdw_slave *slave = dev_to_sdw_dev(dev); + struct rt721_sdca_priv *rt721 = dev_get_drvdata(dev); + unsigned long time; + + if (!rt721->first_hw_init) + return 0; + + if (!slave->unattach_request) { + mutex_lock(&rt721->disable_irq_lock); + if (rt721->disable_irq == true) { + sdw_write_no_pm(slave, SDW_SCP_SDCA_INTMASK1, SDW_SCP_SDCA_INTMASK_SDCA_6); + sdw_write_no_pm(slave, SDW_SCP_SDCA_INTMASK2, SDW_SCP_SDCA_INTMASK_SDCA_8); + rt721->disable_irq = false; + } + mutex_unlock(&rt721->disable_irq_lock); + goto regmap_sync; + } + + time = wait_for_completion_timeout(&slave->initialization_complete, + msecs_to_jiffies(RT721_PROBE_TIMEOUT)); + if (!time) { + dev_err(&slave->dev, "Initialization not complete, timed out\n"); + sdw_show_ping_status(slave->bus, true); + + return -ETIMEDOUT; + } + +regmap_sync: + slave->unattach_request = 0; + regcache_cache_only(rt721->regmap, false); + regcache_sync(rt721->regmap); + regcache_cache_only(rt721->mbq_regmap, false); + regcache_sync(rt721->mbq_regmap); + return 0; +} + +static const struct dev_pm_ops rt721_sdca_pm = { + SET_SYSTEM_SLEEP_PM_OPS(rt721_sdca_dev_system_suspend, rt721_sdca_dev_resume) + SET_RUNTIME_PM_OPS(rt721_sdca_dev_suspend, rt721_sdca_dev_resume, NULL) +}; + +static struct sdw_driver rt721_sdca_sdw_driver = { + .driver = { + .name = "rt721-sdca", + .owner = THIS_MODULE, + .pm = &rt721_sdca_pm, + }, + .probe = rt721_sdca_sdw_probe, + .remove = rt721_sdca_sdw_remove, + .ops = &rt721_sdca_slave_ops, + .id_table = rt721_sdca_id, +}; +module_sdw_driver(rt721_sdca_sdw_driver); + +MODULE_DESCRIPTION("ASoC RT721 SDCA SDW driver"); +MODULE_AUTHOR("Jack Yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt721-sdca-sdw.h b/sound/soc/codecs/rt721-sdca-sdw.h new file mode 100644 index 000000000000..214b31b82583 --- /dev/null +++ b/sound/soc/codecs/rt721-sdca-sdw.h @@ -0,0 +1,150 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * rt721-sdca-sdw.h -- RT721 SDCA ALSA SoC audio driver header + * + * Copyright(c) 2024 Realtek Semiconductor Corp. + */ + +#ifndef __RT721_SDW_H__ +#define __RT721_SDW_H__ + +#include <linux/regmap.h> +#include <linux/soundwire/sdw_registers.h> + +static const struct reg_default rt721_sdca_reg_defaults[] = { + { 0x202d, 0x00 }, + { 0x2f01, 0x00 }, + { 0x2f02, 0x09 }, + { 0x2f03, 0x08 }, + { 0x2f04, 0x00 }, + { 0x2f05, 0x0e }, + { 0x2f06, 0x01 }, + { 0x2f09, 0x00 }, + { 0x2f0a, 0x00 }, + { 0x2f35, 0x00 }, + { 0x2f50, 0xf0 }, + { 0x2f58, 0x07 }, + { 0x2f59, 0x07 }, + { 0x2f5a, 0x00 }, + { 0x2f5b, 0x07 }, + { 0x2f5c, 0x27 }, + { 0x2f5d, 0x07 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_CS01, + RT721_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_CS11, + RT721_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PDE12, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PDE40, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, + RT721_SDCA_CTL_FU_MUTE, CH_L), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, + RT721_SDCA_CTL_FU_MUTE, CH_R), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, + RT721_SDCA_CTL_FU_MUTE, CH_L), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, + RT721_SDCA_CTL_FU_MUTE, CH_R), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, + RT721_SDCA_CTL_FU_MUTE, CH_01), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, + RT721_SDCA_CTL_FU_MUTE, CH_02), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, + RT721_SDCA_CTL_FU_MUTE, CH_03), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, + RT721_SDCA_CTL_FU_MUTE, CH_04), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_CS1F, + RT721_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_IT26, + RT721_SDCA_CTL_VENDOR_DEF, 0), 0x00 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_PDE2A, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_CS31, + RT721_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), 0x09 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, + RT721_SDCA_CTL_FU_MUTE, CH_L), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, + RT721_SDCA_CTL_FU_MUTE, CH_R), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), 0x03 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_OT23, + RT721_SDCA_CTL_VENDOR_DEF, 0), 0x00 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_FU_MUTE, CH_01), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_FU_MUTE, CH_02), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_FU55, + RT721_SDCA_CTL_FU_MUTE, CH_01), 0x01 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_FU55, + RT721_SDCA_CTL_FU_MUTE, CH_02), 0x01 }, +}; + +static const struct reg_default rt721_sdca_mbq_defaults[] = { + { 0x0900007, 0xc004 }, + { 0x2000001, 0x0000 }, + { 0x2000002, 0x0000 }, + { 0x2000003, 0x0000 }, + { 0x2000013, 0x8001 }, + { 0x200003c, 0x0000 }, + { 0x2000046, 0x3400 }, + { 0x5f00044, 0x6040 }, + { 0x5f00045, 0x3333 }, + { 0x5f00048, 0x0000 }, + { 0x6100005, 0x0005 }, + { 0x6100006, 0x0000 }, + { 0x610000d, 0x0051 }, + { 0x6100010, 0x0180 }, + { 0x6100011, 0x0000 }, + { 0x6100013, 0x0000 }, + { 0x6100015, 0x0000 }, + { 0x6100017, 0x8049 }, + { 0x6100025, 0x1000 }, + { 0x6100029, 0x0809 }, + { 0x610002c, 0x2828 }, + { 0x610002d, 0x2929 }, + { 0x610002e, 0x3529 }, + { 0x610002f, 0x2901 }, + { 0x6100053, 0x2630 }, + { 0x6100054, 0x2a2a }, + { 0x6100055, 0x152f }, + { 0x6100057, 0x2200 }, + { 0x610005a, 0x2a4b }, + { 0x610005b, 0x2a00 }, + { 0x610006a, 0x0102 }, + { 0x610006d, 0x0102 }, + { 0x6100092, 0x4f61 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, RT721_SDCA_CTL_FU_VOLUME, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, RT721_SDCA_CTL_FU_VOLUME, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, RT721_SDCA_CTL_FU_VOLUME, + CH_L), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, RT721_SDCA_CTL_FU_VOLUME, + CH_R), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PLATFORM_FU44, RT721_SDCA_CTL_FU_CH_GAIN, + CH_L), 0xfe00 }, + { SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PLATFORM_FU44, RT721_SDCA_CTL_FU_CH_GAIN, + CH_R), 0xfe00 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_FU15, RT721_SDCA_CTL_FU_CH_GAIN, CH_01), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_FU15, RT721_SDCA_CTL_FU_CH_GAIN, CH_02), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_FU15, RT721_SDCA_CTL_FU_CH_GAIN, CH_03), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_FU15, RT721_SDCA_CTL_FU_CH_GAIN, CH_04), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, RT721_SDCA_CTL_FU_VOLUME, + CH_01), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, RT721_SDCA_CTL_FU_VOLUME, + CH_02), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, RT721_SDCA_CTL_FU_VOLUME, + CH_03), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, RT721_SDCA_CTL_FU_VOLUME, + CH_04), 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, RT721_SDCA_CTL_FU_VOLUME, CH_L), + 0x0000 }, + { SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, RT721_SDCA_CTL_FU_VOLUME, CH_R), + 0x0000 }, +}; + +#endif /* __RT721_SDW_H__ */ diff --git a/sound/soc/codecs/rt721-sdca.c b/sound/soc/codecs/rt721-sdca.c new file mode 100644 index 000000000000..36056cb7a3ca --- /dev/null +++ b/sound/soc/codecs/rt721-sdca.c @@ -0,0 +1,1547 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt721-sdca.c -- rt721 SDCA ALSA SoC audio driver +// +// Copyright(c) 2024 Realtek Semiconductor Corp. +// +// + +#include <linux/bitops.h> +#include <sound/core.h> +#include <linux/delay.h> +#include <linux/init.h> +#include <sound/initval.h> +#include <sound/jack.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <sound/pcm.h> +#include <linux/pm_runtime.h> +#include <sound/pcm_params.h> +#include <linux/soundwire/sdw_registers.h> +#include <linux/slab.h> +#include <sound/soc-dapm.h> +#include <sound/tlv.h> + +#include "rt721-sdca.h" +#include "rt-sdw-common.h" + +static void rt721_sdca_jack_detect_handler(struct work_struct *work) +{ + struct rt721_sdca_priv *rt721 = + container_of(work, struct rt721_sdca_priv, jack_detect_work.work); + int btn_type = 0, ret; + + if (!rt721->hs_jack) + return; + + if (!rt721->component->card || !rt721->component->card->instantiated) + return; + + /* SDW_SCP_SDCA_INT_SDCA_6 is used for jack detection */ + if (rt721->scp_sdca_stat1 & SDW_SCP_SDCA_INT_SDCA_6) { + rt721->jack_type = rt_sdca_headset_detect(rt721->regmap, + RT721_SDCA_ENT_GE49); + if (ret < 0) + return; + } + + /* SDW_SCP_SDCA_INT_SDCA_8 is used for button detection */ + if (rt721->scp_sdca_stat2 & SDW_SCP_SDCA_INT_SDCA_8) + btn_type = rt_sdca_button_detect(rt721->regmap, + RT721_SDCA_ENT_HID01, RT721_BUF_ADDR_HID1, + RT721_SDCA_HID_ID); + + if (rt721->jack_type == 0) + btn_type = 0; + + dev_dbg(&rt721->slave->dev, + "in %s, jack_type=%d\n", __func__, rt721->jack_type); + dev_dbg(&rt721->slave->dev, + "in %s, btn_type=0x%x\n", __func__, btn_type); + dev_dbg(&rt721->slave->dev, + "in %s, scp_sdca_stat1=0x%x, scp_sdca_stat2=0x%x\n", __func__, + rt721->scp_sdca_stat1, rt721->scp_sdca_stat2); + + snd_soc_jack_report(rt721->hs_jack, rt721->jack_type | btn_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + if (btn_type) { + /* button released */ + snd_soc_jack_report(rt721->hs_jack, rt721->jack_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + mod_delayed_work(system_power_efficient_wq, + &rt721->jack_btn_check_work, msecs_to_jiffies(200)); + } +} + +static void rt721_sdca_btn_check_handler(struct work_struct *work) +{ + struct rt721_sdca_priv *rt721 = + container_of(work, struct rt721_sdca_priv, jack_btn_check_work.work); + int btn_type = 0, ret, idx; + unsigned int det_mode, offset, val; + unsigned char buf[3]; + + ret = regmap_read(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_GE49, + RT721_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + if (ret < 0) + goto io_error; + + /* pin attached */ + if (det_mode) { + /* read UMP message offset */ + ret = regmap_read(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_HID, RT721_SDCA_ENT_HID01, + RT721_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto io_error; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(rt721->regmap, + RT721_BUF_ADDR_HID1 + offset + idx, &val); + if (ret < 0) + goto io_error; + buf[idx] = val & 0xff; + } + /* Report ID for HID1 */ + if (buf[0] == 0x11) + btn_type = rt_sdca_btn_type(&buf[1]); + } else + rt721->jack_type = 0; + + dev_dbg(&rt721->slave->dev, "%s, btn_type=0x%x\n", __func__, btn_type); + snd_soc_jack_report(rt721->hs_jack, rt721->jack_type | btn_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + if (btn_type) { + /* button released */ + snd_soc_jack_report(rt721->hs_jack, rt721->jack_type, + SND_JACK_HEADSET | + SND_JACK_BTN_0 | SND_JACK_BTN_1 | + SND_JACK_BTN_2 | SND_JACK_BTN_3); + + mod_delayed_work(system_power_efficient_wq, + &rt721->jack_btn_check_work, msecs_to_jiffies(200)); + } + + return; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); +} + +static void rt721_sdca_dmic_preset(struct rt721_sdca_priv *rt721) +{ + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_MISC_POWER_CTL31, 0x8000); + rt_sdca_index_write(rt721->mbq_regmap, RT721_ANA_POW_PART, + RT721_VREF1_HV_CTRL1, 0xe000); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_MISC_POWER_CTL31, 0x8007); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL9, 0x2a2a); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL10, 0x2a00); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL6, 0x2a2a); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL5, 0x2626); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL8, 0x1e00); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL7, 0x1515); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_CH_FLOAT_CTL3, 0x0304); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_CH_FLOAT_CTL4, 0x0304); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_HDA_LEGACY_CTL1, 0x0000); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_IT26, + RT721_SDCA_CTL_VENDOR_DEF, 0), 0x01); + regmap_write(rt721->mbq_regmap, 0x5910009, 0x2e01); + rt_sdca_index_write(rt721->mbq_regmap, RT721_RC_CALIB_CTRL, + RT721_RC_CALIB_CTRL0, 0x0b00); + rt_sdca_index_write(rt721->mbq_regmap, RT721_RC_CALIB_CTRL, + RT721_RC_CALIB_CTRL0, 0x0b40); + regmap_write(rt721->regmap, 0x2f5c, 0x25); +} + +static void rt721_sdca_amp_preset(struct rt721_sdca_priv *rt721) +{ + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_MISC_POWER_CTL31, 0x8000); + rt_sdca_index_write(rt721->mbq_regmap, RT721_ANA_POW_PART, + RT721_VREF1_HV_CTRL1, 0xe000); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_MISC_POWER_CTL31, 0x8007); + regmap_write(rt721->mbq_regmap, 0x5810000, 0x6420); + regmap_write(rt721->mbq_regmap, 0x5810000, 0x6421); + regmap_write(rt721->mbq_regmap, 0x5810000, 0xe421); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_CH_FLOAT_CTL6, 0x5561); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_REG, + RT721_GPIO_PAD_CTRL5, 0x8003); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_OT23, + RT721_SDCA_CTL_VENDOR_DEF, 0), 0x04); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_FU_MUTE, CH_01), 0x00); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_FU_MUTE, CH_02), 0x00); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_FU55, + RT721_SDCA_CTL_FU_MUTE, CH_01), 0x00); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_FU55, + RT721_SDCA_CTL_FU_MUTE, CH_02), 0x00); +} + +static void rt721_sdca_jack_preset(struct rt721_sdca_priv *rt721) +{ + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_MISC_POWER_CTL31, 0x8000); + rt_sdca_index_write(rt721->mbq_regmap, RT721_ANA_POW_PART, + RT721_VREF1_HV_CTRL1, 0xe000); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_MISC_POWER_CTL31, 0x8007); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_GE_REL_CTRL1, 0x8011); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_UMP_HID_CTRL3, 0xcf00); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_UMP_HID_CTRL4, 0x000f); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_UMP_HID_CTRL1, 0x1100); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_UMP_HID_CTRL5, 0x0c12); + rt_sdca_index_write(rt721->mbq_regmap, RT721_JD_CTRL, + RT721_JD_1PIN_GAT_CTRL2, 0xc002); + rt_sdca_index_write(rt721->mbq_regmap, RT721_RC_CALIB_CTRL, + RT721_RC_CALIB_CTRL0, 0x0b00); + rt_sdca_index_write(rt721->mbq_regmap, RT721_RC_CALIB_CTRL, + RT721_RC_CALIB_CTRL0, 0x0b40); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_UAJ_TOP_TCON14, 0x3333); + regmap_write(rt721->mbq_regmap, 0x5810035, 0x0036); + regmap_write(rt721->mbq_regmap, 0x5810030, 0xee00); + rt_sdca_index_write(rt721->mbq_regmap, RT721_CAP_PORT_CTRL, + RT721_HP_AMP_2CH_CAL1, 0x0140); + regmap_write(rt721->mbq_regmap, 0x5810000, 0x0021); + regmap_write(rt721->mbq_regmap, 0x5810000, 0x8021); + rt_sdca_index_write(rt721->mbq_regmap, RT721_CAP_PORT_CTRL, + RT721_HP_AMP_2CH_CAL18, 0x5522); + regmap_write(rt721->mbq_regmap, 0x5b10007, 0x2000); + regmap_write(rt721->mbq_regmap, 0x5B10017, 0x1b0f); + rt_sdca_index_write(rt721->mbq_regmap, RT721_CBJ_CTRL, + RT721_CBJ_A0_GAT_CTRL1, 0x2a02); + rt_sdca_index_write(rt721->mbq_regmap, RT721_CAP_PORT_CTRL, + RT721_HP_AMP_2CH_CAL4, 0xa105); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_UAJ_TOP_TCON14, 0x3b33); + regmap_write(rt721->mbq_regmap, 0x310400, 0x3023); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_UAJ_TOP_TCON14, 0x3f33); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_UAJ_TOP_TCON13, 0x6048); + regmap_write(rt721->mbq_regmap, 0x310401, 0x3000); + regmap_write(rt721->mbq_regmap, 0x310402, 0x1b00); + regmap_write(rt721->mbq_regmap, 0x310300, 0x000f); + regmap_write(rt721->mbq_regmap, 0x310301, 0x3000); + regmap_write(rt721->mbq_regmap, 0x310302, 0x1b00); + rt_sdca_index_write(rt721->mbq_regmap, RT721_VENDOR_ANA_CTL, + RT721_UAJ_TOP_TCON17, 0x0008); + rt_sdca_index_write(rt721->mbq_regmap, RT721_DAC_CTRL, + RT721_DAC_2CH_CTRL3, 0x55ff); + rt_sdca_index_write(rt721->mbq_regmap, RT721_DAC_CTRL, + RT721_DAC_2CH_CTRL4, 0xcc00); + rt_sdca_index_write(rt721->mbq_regmap, RT721_ANA_POW_PART, + RT721_MBIAS_LV_CTRL2, 0x6677); + rt_sdca_index_write(rt721->mbq_regmap, RT721_ANA_POW_PART, + RT721_VREF2_LV_CTRL1, 0x7600); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL2, 0x1234); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL3, 0x3512); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL1, 0x4040); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_ENT_FLOAT_CTL4, 0x1201); + regmap_write(rt721->regmap, 0x2f58, 0x07); +} + +static void rt721_sdca_jack_init(struct rt721_sdca_priv *rt721) +{ + mutex_lock(&rt721->calibrate_mutex); + if (rt721->hs_jack) { + sdw_write_no_pm(rt721->slave, SDW_SCP_SDCA_INTMASK1, + SDW_SCP_SDCA_INTMASK_SDCA_0 | SDW_SCP_SDCA_INTMASK_SDCA_6); + sdw_write_no_pm(rt721->slave, SDW_SCP_SDCA_INTMASK2, + SDW_SCP_SDCA_INTMASK_SDCA_8); + dev_dbg(&rt721->slave->dev, "in %s enable\n", __func__); + rt_sdca_index_write(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_HDA_LEGACY_UAJ_CTL, 0x036E); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_XU03, + RT721_SDCA_CTL_SELECTED_MODE, 0), 0); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_XU0D, + RT721_SDCA_CTL_SELECTED_MODE, 0), 0); + rt_sdca_index_update_bits(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_GE_REL_CTRL1, 0x4000, 0x4000); + } + mutex_unlock(&rt721->calibrate_mutex); +} + +static int rt721_sdca_set_jack_detect(struct snd_soc_component *component, + struct snd_soc_jack *hs_jack, void *data) +{ + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + int ret; + + rt721->hs_jack = hs_jack; + + ret = pm_runtime_resume_and_get(component->dev); + if (ret < 0) { + if (ret != -EACCES) { + dev_err(component->dev, "%s: failed to resume %d\n", __func__, ret); + return ret; + } + /* pm_runtime not enabled yet */ + dev_dbg(component->dev, "%s: skipping jack init for now\n", __func__); + return 0; + } + + rt721_sdca_jack_init(rt721); + + pm_runtime_mark_last_busy(component->dev); + pm_runtime_put_autosuspend(component->dev); + + return 0; +} + +/* For SDCA control DAC/ADC Gain */ +static int rt721_sdca_set_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned int read_l, read_r, gain_l_val, gain_r_val; + unsigned int adc_vol_flag = 0, changed = 0; + unsigned int lvalue, rvalue; + const unsigned int interval_offset = 0xc0; + const unsigned int tendA = 0x200; + const unsigned int tendB = 0xa00; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume") || + strstr(ucontrol->id.name, "FU0F Capture Volume")) + adc_vol_flag = 1; + + regmap_read(rt721->mbq_regmap, mc->reg, &lvalue); + regmap_read(rt721->mbq_regmap, mc->rreg, &rvalue); + + /* L Channel */ + gain_l_val = ucontrol->value.integer.value[0]; + if (gain_l_val > mc->max) + gain_l_val = mc->max; + + if (mc->shift == 8) { + /* boost gain */ + gain_l_val = gain_l_val * tendB; + } else if (mc->shift == 1) { + /* FU33 boost gain */ + if (gain_l_val == 0) + gain_l_val = 0x8000; + else + gain_l_val = (gain_l_val - 1) * tendA; + } else { + /* ADC/DAC gain */ + if (adc_vol_flag) + gain_l_val = 0x1e00 - ((mc->max - gain_l_val) * interval_offset); + else + gain_l_val = 0 - ((mc->max - gain_l_val) * interval_offset); + gain_l_val &= 0xffff; + } + + /* R Channel */ + gain_r_val = ucontrol->value.integer.value[1]; + if (gain_r_val > mc->max) + gain_r_val = mc->max; + + if (mc->shift == 8) { + /* boost gain */ + gain_r_val = gain_r_val * tendB; + } else if (mc->shift == 1) { + /* FU33 boost gain */ + if (gain_r_val == 0) + gain_r_val = 0x8000; + else + gain_r_val = (gain_r_val - 1) * tendA; + } else { + /* ADC/DAC gain */ + if (adc_vol_flag) + gain_r_val = 0x1e00 - ((mc->max - gain_r_val) * interval_offset); + else + gain_r_val = 0 - ((mc->max - gain_r_val) * interval_offset); + gain_r_val &= 0xffff; + } + + if (lvalue != gain_l_val || rvalue != gain_r_val) + changed = 1; + else + return 0; + + /* Lch*/ + regmap_write(rt721->mbq_regmap, mc->reg, gain_l_val); + + /* Rch */ + regmap_write(rt721->mbq_regmap, mc->rreg, gain_r_val); + + regmap_read(rt721->mbq_regmap, mc->reg, &read_l); + regmap_read(rt721->mbq_regmap, mc->rreg, &read_r); + if (read_r == gain_r_val && read_l == gain_l_val) + return changed; + + return -EIO; +} + +static int rt721_sdca_set_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + struct soc_mixer_control *mc = + (struct soc_mixer_control *)kcontrol->private_value; + unsigned int read_l, read_r, ctl_l = 0, ctl_r = 0; + unsigned int adc_vol_flag = 0; + const unsigned int interval_offset = 0xc0; + const unsigned int tendB = 0xa00; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume") || + strstr(ucontrol->id.name, "FU0F Capture Volume")) + adc_vol_flag = 1; + + regmap_read(rt721->mbq_regmap, mc->reg, &read_l); + regmap_read(rt721->mbq_regmap, mc->rreg, &read_r); + + if (mc->shift == 8) /* boost gain */ + ctl_l = read_l / tendB; + else { + if (adc_vol_flag) + ctl_l = mc->max - (((0x1e00 - read_l) & 0xffff) / interval_offset); + else + ctl_l = mc->max - (((0 - read_l) & 0xffff) / interval_offset); + } + + if (read_l != read_r) { + if (mc->shift == 8) /* boost gain */ + ctl_r = read_r / tendB; + else { /* ADC/DAC gain */ + if (adc_vol_flag) + ctl_r = mc->max - (((0x1e00 - read_r) & 0xffff) / interval_offset); + else + ctl_r = mc->max - (((0 - read_r) & 0xffff) / interval_offset); + } + } else { + ctl_r = ctl_l; + } + + ucontrol->value.integer.value[0] = ctl_l; + ucontrol->value.integer.value[1] = ctl_r; + + return 0; +} + +static int rt721_sdca_set_fu1e_capture_ctl(struct rt721_sdca_priv *rt721) +{ + int err, i; + unsigned int ch_mute; + + for (i = 0; i < ARRAY_SIZE(rt721->fu1e_mixer_mute); i++) { + ch_mute = rt721->fu1e_dapm_mute || rt721->fu1e_mixer_mute[i]; + err = regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, + RT721_SDCA_CTL_FU_MUTE, CH_01) + i, ch_mute); + if (err < 0) + return err; + } + + return 0; +} + +static int rt721_sdca_fu1e_capture_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + struct rt721_sdca_dmic_kctrl_priv *p = + (struct rt721_sdca_dmic_kctrl_priv *)kcontrol->private_value; + unsigned int i; + + for (i = 0; i < p->count; i++) + ucontrol->value.integer.value[i] = !rt721->fu1e_mixer_mute[i]; + + return 0; +} + +static int rt721_sdca_fu1e_capture_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + struct rt721_sdca_dmic_kctrl_priv *p = + (struct rt721_sdca_dmic_kctrl_priv *)kcontrol->private_value; + int err, changed = 0, i; + + for (i = 0; i < p->count; i++) { + if (rt721->fu1e_mixer_mute[i] != !ucontrol->value.integer.value[i]) + changed = 1; + rt721->fu1e_mixer_mute[i] = !ucontrol->value.integer.value[i]; + } + + err = rt721_sdca_set_fu1e_capture_ctl(rt721); + if (err < 0) + return err; + + return changed; +} + +static int rt721_sdca_set_fu0f_capture_ctl(struct rt721_sdca_priv *rt721) +{ + int err; + unsigned int ch_l, ch_r; + + ch_l = (rt721->fu0f_dapm_mute || rt721->fu0f_mixer_l_mute) ? 0x01 : 0x00; + ch_r = (rt721->fu0f_dapm_mute || rt721->fu0f_mixer_r_mute) ? 0x01 : 0x00; + + err = regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, + RT721_SDCA_CTL_FU_MUTE, CH_L), ch_l); + if (err < 0) + return err; + + err = regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, + RT721_SDCA_CTL_FU_MUTE, CH_R), ch_r); + if (err < 0) + return err; + + return 0; +} + +static int rt721_sdca_fu0f_capture_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + + ucontrol->value.integer.value[0] = !rt721->fu0f_mixer_l_mute; + ucontrol->value.integer.value[1] = !rt721->fu0f_mixer_r_mute; + return 0; +} + +static int rt721_sdca_fu0f_capture_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + int err, changed = 0; + + if (rt721->fu0f_mixer_l_mute != !ucontrol->value.integer.value[0] || + rt721->fu0f_mixer_r_mute != !ucontrol->value.integer.value[1]) + changed = 1; + + rt721->fu0f_mixer_l_mute = !ucontrol->value.integer.value[0]; + rt721->fu0f_mixer_r_mute = !ucontrol->value.integer.value[1]; + err = rt721_sdca_set_fu0f_capture_ctl(rt721); + if (err < 0) + return err; + + return changed; +} + +static int rt721_sdca_fu_info(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_info *uinfo) +{ + struct rt721_sdca_dmic_kctrl_priv *p = + (struct rt721_sdca_dmic_kctrl_priv *)kcontrol->private_value; + + if (p->max == 1) + uinfo->type = SNDRV_CTL_ELEM_TYPE_BOOLEAN; + else + uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; + uinfo->count = p->count; + uinfo->value.integer.min = 0; + uinfo->value.integer.max = p->max; + return 0; +} + +static int rt721_sdca_dmic_set_gain_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + struct rt721_sdca_dmic_kctrl_priv *p = + (struct rt721_sdca_dmic_kctrl_priv *)kcontrol->private_value; + unsigned int boost_step = 0x0a00; + unsigned int vol_max = 0x1e00; + unsigned int regvalue, ctl, i; + unsigned int adc_vol_flag = 0; + const unsigned int interval_offset = 0xc0; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume")) + adc_vol_flag = 1; + + /* check all channels */ + for (i = 0; i < p->count; i++) { + regmap_read(rt721->mbq_regmap, p->reg_base + i, &regvalue); + + if (!adc_vol_flag) /* boost gain */ + ctl = regvalue / boost_step; + else { /* ADC gain */ + if (adc_vol_flag) + ctl = p->max - (((vol_max - regvalue) & 0xffff) / interval_offset); + else + ctl = p->max - (((0 - regvalue) & 0xffff) / interval_offset); + } + + ucontrol->value.integer.value[i] = ctl; + } + + return 0; +} + +static int rt721_sdca_dmic_set_gain_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); + struct rt721_sdca_dmic_kctrl_priv *p = + (struct rt721_sdca_dmic_kctrl_priv *)kcontrol->private_value; + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned int boost_step = 0x0a00; + unsigned int vol_max = 0x1e00; + unsigned int gain_val[4]; + unsigned int i, adc_vol_flag = 0, changed = 0; + unsigned int regvalue[4]; + const unsigned int interval_offset = 0xc0; + int err; + + if (strstr(ucontrol->id.name, "FU1E Capture Volume")) + adc_vol_flag = 1; + + /* check all channels */ + for (i = 0; i < p->count; i++) { + regmap_read(rt721->mbq_regmap, p->reg_base + i, &regvalue[i]); + + gain_val[i] = ucontrol->value.integer.value[i]; + if (gain_val[i] > p->max) + gain_val[i] = p->max; + + if (!adc_vol_flag) /* boost gain */ + gain_val[i] = gain_val[i] * boost_step; + else { /* ADC gain */ + gain_val[i] = vol_max - ((p->max - gain_val[i]) * interval_offset); + gain_val[i] &= 0xffff; + } + + if (regvalue[i] != gain_val[i]) + changed = 1; + } + + if (!changed) + return 0; + + for (i = 0; i < p->count; i++) { + err = regmap_write(rt721->mbq_regmap, p->reg_base + i, gain_val[i]); + if (err < 0) + dev_err(&rt721->slave->dev, "%#08x can't be set\n", p->reg_base + i); + } + + return changed; +} + +static const DECLARE_TLV_DB_SCALE(out_vol_tlv, -6525, 75, 0); +static const DECLARE_TLV_DB_SCALE(mic_vol_tlv, -1725, 75, 0); +static const DECLARE_TLV_DB_SCALE(boost_vol_tlv, 0, 1000, 0); +static const DECLARE_TLV_DB_SCALE(mic2_boost_vol_tlv, -200, 200, 0); + +static const struct snd_kcontrol_new rt721_sdca_controls[] = { + /* Headphone playback settings */ + SOC_DOUBLE_R_EXT_TLV("FU05 Playback Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, + RT721_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, + RT721_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x57, 0, + rt721_sdca_set_gain_get, rt721_sdca_set_gain_put, out_vol_tlv), + /* Headset mic capture settings */ + SOC_DOUBLE_EXT("FU0F Capture Switch", SND_SOC_NOPM, 0, 1, 1, 0, + rt721_sdca_fu0f_capture_get, rt721_sdca_fu0f_capture_put), + SOC_DOUBLE_R_EXT_TLV("FU0F Capture Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, + RT721_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU0F, + RT721_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x3f, 0, + rt721_sdca_set_gain_get, rt721_sdca_set_gain_put, mic_vol_tlv), + SOC_DOUBLE_R_EXT_TLV("FU33 Boost Volume", + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PLATFORM_FU44, + RT721_SDCA_CTL_FU_CH_GAIN, CH_L), + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PLATFORM_FU44, + RT721_SDCA_CTL_FU_CH_GAIN, CH_R), 1, 0x15, 0, + rt721_sdca_set_gain_get, rt721_sdca_set_gain_put, mic2_boost_vol_tlv), + /* AMP playback settings */ + SOC_DOUBLE_R_EXT_TLV("FU06 Playback Volume", + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, + RT721_SDCA_CTL_FU_VOLUME, CH_L), + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, + RT721_SDCA_CTL_FU_VOLUME, CH_R), 0, 0x57, 0, + rt721_sdca_set_gain_get, rt721_sdca_set_gain_put, out_vol_tlv), + /* DMIC capture settings */ + RT_SDCA_FU_CTRL("FU1E Capture Switch", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, + RT721_SDCA_CTL_FU_MUTE, CH_01), 1, 1, 4, rt721_sdca_fu_info, + rt721_sdca_fu1e_capture_get, rt721_sdca_fu1e_capture_put), + RT_SDCA_EXT_TLV("FU1E Capture Volume", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_USER_FU1E, + RT721_SDCA_CTL_FU_VOLUME, CH_01), + rt721_sdca_dmic_set_gain_get, rt721_sdca_dmic_set_gain_put, + 4, 0x3f, mic_vol_tlv, rt721_sdca_fu_info), + RT_SDCA_EXT_TLV("FU15 Boost Volume", + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_FU15, + RT721_SDCA_CTL_FU_CH_GAIN, CH_01), + rt721_sdca_dmic_set_gain_get, rt721_sdca_dmic_set_gain_put, + 4, 3, boost_vol_tlv, rt721_sdca_fu_info), +}; + +static int rt721_sdca_adc_mux_get(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = + snd_soc_dapm_kcontrol_component(kcontrol); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned int val = 0, mask_sft, mask; + + if (strstr(ucontrol->id.name, "ADC 09 Mux")) { + mask_sft = 12; + mask = 0x7; + } else if (strstr(ucontrol->id.name, "ADC 08 R Mux")) { + mask_sft = 10; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 08 L Mux")) { + mask_sft = 8; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 10 R Mux")) { + mask_sft = 6; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 10 L Mux")) { + mask_sft = 4; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 07 R Mux")) { + mask_sft = 2; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 07 L Mux")) { + mask_sft = 0; + mask = 0x3; + } else + return -EINVAL; + + rt_sdca_index_read(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_HDA_LEGACY_MUX_CTL0, &val); + + ucontrol->value.enumerated.item[0] = (val >> mask_sft) & mask; + + return 0; +} + +static int rt721_sdca_adc_mux_put(struct snd_kcontrol *kcontrol, + struct snd_ctl_elem_value *ucontrol) +{ + struct snd_soc_component *component = + snd_soc_dapm_kcontrol_component(kcontrol); + struct snd_soc_dapm_context *dapm = + snd_soc_dapm_kcontrol_dapm(kcontrol); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + struct soc_enum *e = (struct soc_enum *)kcontrol->private_value; + unsigned int *item = ucontrol->value.enumerated.item; + unsigned int val, val2 = 0, change, mask_sft, mask; + unsigned int check; + + if (item[0] >= e->items) + return -EINVAL; + + if (strstr(ucontrol->id.name, "ADC 09 Mux")) { + mask_sft = 12; + mask = 0x7; + } else if (strstr(ucontrol->id.name, "ADC 08 R Mux")) { + mask_sft = 10; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 08 L Mux")) { + mask_sft = 8; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 10 R Mux")) { + mask_sft = 6; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 10 L Mux")) { + mask_sft = 4; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 07 R Mux")) { + mask_sft = 2; + mask = 0x3; + } else if (strstr(ucontrol->id.name, "ADC 07 L Mux")) { + mask_sft = 0; + mask = 0x3; + } else + return -EINVAL; + + val = snd_soc_enum_item_to_val(e, item[0]) << e->shift_l; + rt_sdca_index_read(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_HDA_LEGACY_MUX_CTL0, &val2); + + if (strstr(ucontrol->id.name, "ADC 09 Mux")) + val2 = (val2 >> mask_sft) & 0x7; + else + val2 = (val2 >> mask_sft) & 0x3; + + if (val == val2) + change = 0; + else + change = 1; + + if (change) { + rt_sdca_index_read(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_HDA_LEGACY_MUX_CTL0, &check); + rt_sdca_index_update_bits(rt721->mbq_regmap, RT721_HDA_SDCA_FLOAT, + RT721_HDA_LEGACY_MUX_CTL0, mask << mask_sft, + val << mask_sft); + } + + snd_soc_dapm_mux_update_power(dapm, kcontrol, + item[0], e, NULL); + + return change; +} + +static const char * const adc09_mux_text[] = { + "MIC2", + "LINE1", + "LINE2", +}; +static const char * const adc07_10_mux_text[] = { + "DMIC1 RE", + "DMIC1 FE", + "DMIC2 RE", + "DMIC2 FE", +}; + +static SOC_ENUM_SINGLE_DECL( + rt721_adc09_enum, SND_SOC_NOPM, 0, adc09_mux_text); +static SOC_ENUM_SINGLE_DECL( + rt721_dmic_enum, SND_SOC_NOPM, 0, adc07_10_mux_text); + +static const struct snd_kcontrol_new rt721_sdca_adc09_mux = + SOC_DAPM_ENUM_EXT("ADC 09 Mux", rt721_adc09_enum, + rt721_sdca_adc_mux_get, rt721_sdca_adc_mux_put); +static const struct snd_kcontrol_new rt721_sdca_adc08_r_mux = + SOC_DAPM_ENUM_EXT("ADC 08 R Mux", rt721_dmic_enum, + rt721_sdca_adc_mux_get, rt721_sdca_adc_mux_put); +static const struct snd_kcontrol_new rt721_sdca_adc08_l_mux = + SOC_DAPM_ENUM_EXT("ADC 08 L Mux", rt721_dmic_enum, + rt721_sdca_adc_mux_get, rt721_sdca_adc_mux_put); +static const struct snd_kcontrol_new rt721_sdca_adc10_r_mux = + SOC_DAPM_ENUM_EXT("ADC 10 R Mux", rt721_dmic_enum, + rt721_sdca_adc_mux_get, rt721_sdca_adc_mux_put); +static const struct snd_kcontrol_new rt721_sdca_adc10_l_mux = + SOC_DAPM_ENUM_EXT("ADC 10 L Mux", rt721_dmic_enum, + rt721_sdca_adc_mux_get, rt721_sdca_adc_mux_put); +static const struct snd_kcontrol_new rt721_sdca_adc07_r_mux = + SOC_DAPM_ENUM_EXT("ADC 07 R Mux", rt721_dmic_enum, + rt721_sdca_adc_mux_get, rt721_sdca_adc_mux_put); +static const struct snd_kcontrol_new rt721_sdca_adc07_l_mux = + SOC_DAPM_ENUM_EXT("ADC 07 L Mux", rt721_dmic_enum, + rt721_sdca_adc_mux_get, rt721_sdca_adc_mux_put); + + +static int rt721_sdca_fu42_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + msleep(100); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, + RT721_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, + RT721_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, + RT721_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_USER_FU05, + RT721_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt721_sdca_fu21_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, + RT721_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, + RT721_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, + RT721_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_USER_FU06, + RT721_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt721_sdca_fu23_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned char unmute = 0x0, mute = 0x1; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_FU_MUTE, CH_L), unmute); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_FU_MUTE, CH_R), unmute); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_FU_MUTE, CH_L), mute); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE23, + RT721_SDCA_CTL_FU_MUTE, CH_R), mute); + break; + } + return 0; +} + +static int rt721_sdca_fu113_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + rt721->fu1e_dapm_mute = false; + rt721_sdca_set_fu1e_capture_ctl(rt721); + break; + case SND_SOC_DAPM_PRE_PMD: + rt721->fu1e_dapm_mute = true; + rt721_sdca_set_fu1e_capture_ctl(rt721); + break; + } + return 0; +} + +static int rt721_sdca_fu36_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + rt721->fu0f_dapm_mute = false; + rt721_sdca_set_fu0f_capture_ctl(rt721); + break; + case SND_SOC_DAPM_PRE_PMD: + rt721->fu0f_dapm_mute = true; + rt721_sdca_set_fu0f_capture_ctl(rt721); + break; + } + return 0; +} + +static int rt721_sdca_pde47_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PDE40, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PDE40, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt721_sdca_pde41_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE41, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_PDE41, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt721_sdca_pde11_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_PDE2A, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_PDE2A, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static int rt721_sdca_pde34_event(struct snd_soc_dapm_widget *w, + struct snd_kcontrol *kcontrol, int event) +{ + struct snd_soc_component *component = + snd_soc_dapm_to_component(w->dapm); + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + unsigned char ps0 = 0x0, ps3 = 0x3; + + switch (event) { + case SND_SOC_DAPM_POST_PMU: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PDE12, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), ps0); + break; + case SND_SOC_DAPM_PRE_PMD: + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_PDE12, + RT721_SDCA_CTL_REQ_POWER_STATE, 0), ps3); + break; + } + return 0; +} + +static const struct snd_soc_dapm_widget rt721_sdca_dapm_widgets[] = { + SND_SOC_DAPM_OUTPUT("HP"), + SND_SOC_DAPM_OUTPUT("SPK"), + SND_SOC_DAPM_INPUT("MIC2"), + SND_SOC_DAPM_INPUT("LINE1"), + SND_SOC_DAPM_INPUT("LINE2"), + SND_SOC_DAPM_INPUT("DMIC1_2"), + SND_SOC_DAPM_INPUT("DMIC3_4"), + + SND_SOC_DAPM_SUPPLY("PDE 41", SND_SOC_NOPM, 0, 0, + rt721_sdca_pde41_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 47", SND_SOC_NOPM, 0, 0, + rt721_sdca_pde47_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 11", SND_SOC_NOPM, 0, 0, + rt721_sdca_pde11_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_SUPPLY("PDE 34", SND_SOC_NOPM, 0, 0, + rt721_sdca_pde34_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + + SND_SOC_DAPM_DAC_E("FU 21", NULL, SND_SOC_NOPM, 0, 0, + rt721_sdca_fu21_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_DAC_E("FU 23", NULL, SND_SOC_NOPM, 0, 0, + rt721_sdca_fu23_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_DAC_E("FU 42", NULL, SND_SOC_NOPM, 0, 0, + rt721_sdca_fu42_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("FU 36", NULL, SND_SOC_NOPM, 0, 0, + rt721_sdca_fu36_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_ADC_E("FU 113", NULL, SND_SOC_NOPM, 0, 0, + rt721_sdca_fu113_event, + SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD), + SND_SOC_DAPM_MUX("ADC 09 Mux", SND_SOC_NOPM, 0, 0, + &rt721_sdca_adc09_mux), + SND_SOC_DAPM_MUX("ADC 08 R Mux", SND_SOC_NOPM, 0, 0, + &rt721_sdca_adc08_r_mux), + SND_SOC_DAPM_MUX("ADC 08 L Mux", SND_SOC_NOPM, 0, 0, + &rt721_sdca_adc08_l_mux), + SND_SOC_DAPM_MUX("ADC 10 R Mux", SND_SOC_NOPM, 0, 0, + &rt721_sdca_adc10_r_mux), + SND_SOC_DAPM_MUX("ADC 10 L Mux", SND_SOC_NOPM, 0, 0, + &rt721_sdca_adc10_l_mux), + SND_SOC_DAPM_MUX("ADC 07 R Mux", SND_SOC_NOPM, 0, 0, + &rt721_sdca_adc07_r_mux), + SND_SOC_DAPM_MUX("ADC 07 L Mux", SND_SOC_NOPM, 0, 0, + &rt721_sdca_adc07_l_mux), + + SND_SOC_DAPM_AIF_IN("DP1RX", "DP1 Headphone Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("DP2TX", "DP2 Headset Capture", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_IN("DP3RX", "DP3 Speaker Playback", 0, SND_SOC_NOPM, 0, 0), + SND_SOC_DAPM_AIF_OUT("DP6TX", "DP6 DMic Capture", 0, SND_SOC_NOPM, 0, 0), +}; + +static const struct snd_soc_dapm_route rt721_sdca_audio_map[] = { + {"FU 42", NULL, "DP1RX"}, + {"FU 21", NULL, "DP3RX"}, + {"FU 23", NULL, "DP3RX"}, + + {"ADC 09 Mux", "MIC2", "MIC2"}, + {"ADC 09 Mux", "LINE1", "LINE1"}, + {"ADC 09 Mux", "LINE2", "LINE2"}, + {"ADC 07 R Mux", "DMIC1 RE", "DMIC1_2"}, + {"ADC 07 R Mux", "DMIC1 FE", "DMIC1_2"}, + {"ADC 07 R Mux", "DMIC2 RE", "DMIC3_4"}, + {"ADC 07 R Mux", "DMIC2 FE", "DMIC3_4"}, + {"ADC 07 L Mux", "DMIC1 RE", "DMIC1_2"}, + {"ADC 07 L Mux", "DMIC1 FE", "DMIC1_2"}, + {"ADC 07 L Mux", "DMIC2 RE", "DMIC3_4"}, + {"ADC 07 L Mux", "DMIC2 FE", "DMIC3_4"}, + {"ADC 08 R Mux", "DMIC1 RE", "DMIC1_2"}, + {"ADC 08 R Mux", "DMIC1 FE", "DMIC1_2"}, + {"ADC 08 R Mux", "DMIC2 RE", "DMIC3_4"}, + {"ADC 08 R Mux", "DMIC2 FE", "DMIC3_4"}, + {"ADC 08 L Mux", "DMIC1 RE", "DMIC1_2"}, + {"ADC 08 L Mux", "DMIC1 FE", "DMIC1_2"}, + {"ADC 08 L Mux", "DMIC2 RE", "DMIC3_4"}, + {"ADC 08 L Mux", "DMIC2 FE", "DMIC3_4"}, + {"ADC 10 R Mux", "DMIC1 RE", "DMIC1_2"}, + {"ADC 10 R Mux", "DMIC1 FE", "DMIC1_2"}, + {"ADC 10 R Mux", "DMIC2 RE", "DMIC3_4"}, + {"ADC 10 R Mux", "DMIC2 FE", "DMIC3_4"}, + {"ADC 10 L Mux", "DMIC1 RE", "DMIC1_2"}, + {"ADC 10 L Mux", "DMIC1 FE", "DMIC1_2"}, + {"ADC 10 L Mux", "DMIC2 RE", "DMIC3_4"}, + {"ADC 10 L Mux", "DMIC2 FE", "DMIC3_4"}, + {"FU 36", NULL, "PDE 34"}, + {"FU 36", NULL, "ADC 09 Mux"}, + {"FU 113", NULL, "PDE 11"}, + {"FU 113", NULL, "ADC 07 R Mux"}, + {"FU 113", NULL, "ADC 07 L Mux"}, + {"FU 113", NULL, "ADC 10 R Mux"}, + {"FU 113", NULL, "ADC 10 L Mux"}, + {"DP2TX", NULL, "FU 36"}, + {"DP6TX", NULL, "FU 113"}, + + {"HP", NULL, "PDE 47"}, + {"HP", NULL, "FU 42"}, + {"SPK", NULL, "PDE 41"}, + {"SPK", NULL, "FU 21"}, + {"SPK", NULL, "FU 23"}, +}; + +static int rt721_sdca_parse_dt(struct rt721_sdca_priv *rt721, struct device *dev) +{ + device_property_read_u32(dev, "realtek,jd-src", &rt721->jd_src); + + return 0; +} + +static int rt721_sdca_probe(struct snd_soc_component *component) +{ + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + int ret; + + rt721_sdca_parse_dt(rt721, &rt721->slave->dev); + rt721->component = component; + + ret = pm_runtime_resume(component->dev); + if (ret < 0 && ret != -EACCES) + return ret; + + return 0; +} + +static const struct snd_soc_component_driver soc_sdca_dev_rt721 = { + .probe = rt721_sdca_probe, + .controls = rt721_sdca_controls, + .num_controls = ARRAY_SIZE(rt721_sdca_controls), + .dapm_widgets = rt721_sdca_dapm_widgets, + .num_dapm_widgets = ARRAY_SIZE(rt721_sdca_dapm_widgets), + .dapm_routes = rt721_sdca_audio_map, + .num_dapm_routes = ARRAY_SIZE(rt721_sdca_audio_map), + .set_jack = rt721_sdca_set_jack_detect, + .endianness = 1, +}; + +static int rt721_sdca_set_sdw_stream(struct snd_soc_dai *dai, void *sdw_stream, + int direction) +{ + snd_soc_dai_dma_data_set(dai, direction, sdw_stream); + + return 0; +} + +static void rt721_sdca_shutdown(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + snd_soc_dai_set_dma_data(dai, substream, NULL); +} + +static int rt721_sdca_pcm_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + struct sdw_stream_config stream_config; + struct sdw_port_config port_config; + enum sdw_data_direction direction; + struct sdw_stream_runtime *sdw_stream; + int retval, port, num_channels; + unsigned int sampling_rate; + + dev_dbg(dai->dev, "%s %s", __func__, dai->name); + sdw_stream = snd_soc_dai_get_dma_data(dai, substream); + + if (!sdw_stream) + return -EINVAL; + + if (!rt721->slave) + return -EINVAL; + + /* + * RT721_AIF1 with port = 1 for headphone playback + * RT721_AIF1 with port = 2 for headset-mic capture + * RT721_AIF2 with port = 3 for speaker playback + * RT721_AIF3 with port = 6 for digital-mic capture + */ + if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { + direction = SDW_DATA_DIR_RX; + if (dai->id == RT721_AIF1) + port = 1; + else if (dai->id == RT721_AIF2) + port = 3; + else + return -EINVAL; + } else { + direction = SDW_DATA_DIR_TX; + if (dai->id == RT721_AIF1) + port = 2; + else if (dai->id == RT721_AIF3) + port = 6; + else + return -EINVAL; + } + stream_config.frame_rate = params_rate(params); + stream_config.ch_count = params_channels(params); + stream_config.bps = snd_pcm_format_width(params_format(params)); + stream_config.direction = direction; + + num_channels = params_channels(params); + port_config.ch_mask = GENMASK(num_channels - 1, 0); + port_config.num = port; + + retval = sdw_stream_add_slave(rt721->slave, &stream_config, + &port_config, 1, sdw_stream); + if (retval) { + dev_err(dai->dev, "Unable to configure port\n"); + return retval; + } + + if (params_channels(params) > 16) { + dev_err(component->dev, "Unsupported channels %d\n", + params_channels(params)); + return -EINVAL; + } + + /* sampling rate configuration */ + switch (params_rate(params)) { + case 8000: + sampling_rate = RT721_SDCA_RATE_8000HZ; + break; + case 16000: + sampling_rate = RT721_SDCA_RATE_16000HZ; + break; + case 24000: + sampling_rate = RT721_SDCA_RATE_24000HZ; + break; + case 32000: + sampling_rate = RT721_SDCA_RATE_32000HZ; + break; + case 44100: + sampling_rate = RT721_SDCA_RATE_44100HZ; + break; + case 48000: + sampling_rate = RT721_SDCA_RATE_48000HZ; + break; + case 96000: + sampling_rate = RT721_SDCA_RATE_96000HZ; + break; + case 192000: + sampling_rate = RT721_SDCA_RATE_192000HZ; + break; + case 384000: + sampling_rate = RT721_SDCA_RATE_384000HZ; + break; + case 768000: + sampling_rate = RT721_SDCA_RATE_768000HZ; + break; + default: + dev_err(component->dev, "Rate %d is not supported\n", + params_rate(params)); + return -EINVAL; + } + + /* set sampling frequency */ + if (dai->id == RT721_AIF1) { + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_CS01, + RT721_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_JACK_CODEC, RT721_SDCA_ENT_CS11, + RT721_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + } + + if (dai->id == RT721_AIF2) + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_AMP, RT721_SDCA_ENT_CS31, + RT721_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + + if (dai->id == RT721_AIF3) + regmap_write(rt721->regmap, + SDW_SDCA_CTL(FUNC_NUM_MIC_ARRAY, RT721_SDCA_ENT_CS1F, + RT721_SDCA_CTL_SAMPLE_FREQ_INDEX, 0), sampling_rate); + + return 0; +} + +static int rt721_sdca_pcm_hw_free(struct snd_pcm_substream *substream, + struct snd_soc_dai *dai) +{ + struct snd_soc_component *component = dai->component; + struct rt721_sdca_priv *rt721 = snd_soc_component_get_drvdata(component); + struct sdw_stream_runtime *sdw_stream = + snd_soc_dai_get_dma_data(dai, substream); + + if (!rt721->slave) + return -EINVAL; + + sdw_stream_remove_slave(rt721->slave, sdw_stream); + return 0; +} + +#define RT721_STEREO_RATES (SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | \ + SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_192000) +#define RT721_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE | \ + SNDRV_PCM_FMTBIT_S24_LE) + +static const struct snd_soc_dai_ops rt721_sdca_ops = { + .hw_params = rt721_sdca_pcm_hw_params, + .hw_free = rt721_sdca_pcm_hw_free, + .set_stream = rt721_sdca_set_sdw_stream, + .shutdown = rt721_sdca_shutdown, +}; + +static struct snd_soc_dai_driver rt721_sdca_dai[] = { + { + .name = "rt721-sdca-aif1", + .id = RT721_AIF1, + .playback = { + .stream_name = "DP1 Headphone Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT721_STEREO_RATES, + .formats = RT721_FORMATS, + }, + .capture = { + .stream_name = "DP2 Headset Capture", + .channels_min = 1, + .channels_max = 2, + .rates = RT721_STEREO_RATES, + .formats = RT721_FORMATS, + }, + .ops = &rt721_sdca_ops, + }, + { + .name = "rt721-sdca-aif2", + .id = RT721_AIF2, + .playback = { + .stream_name = "DP3 Speaker Playback", + .channels_min = 1, + .channels_max = 2, + .rates = RT721_STEREO_RATES, + .formats = RT721_FORMATS, + }, + .ops = &rt721_sdca_ops, + }, + { + .name = "rt721-sdca-aif3", + .id = RT721_AIF3, + .capture = { + .stream_name = "DP6 DMic Capture", + .channels_min = 1, + .channels_max = 4, + .rates = RT721_STEREO_RATES, + .formats = RT721_FORMATS, + }, + .ops = &rt721_sdca_ops, + } +}; + +int rt721_sdca_init(struct device *dev, struct regmap *regmap, + struct regmap *mbq_regmap, struct sdw_slave *slave) +{ + struct rt721_sdca_priv *rt721; + + rt721 = devm_kzalloc(dev, sizeof(*rt721), GFP_KERNEL); + if (!rt721) + return -ENOMEM; + + dev_set_drvdata(dev, rt721); + rt721->slave = slave; + rt721->regmap = regmap; + rt721->mbq_regmap = mbq_regmap; + + regcache_cache_only(rt721->regmap, true); + regcache_cache_only(rt721->mbq_regmap, true); + + mutex_init(&rt721->calibrate_mutex); + mutex_init(&rt721->disable_irq_lock); + + INIT_DELAYED_WORK(&rt721->jack_detect_work, rt721_sdca_jack_detect_handler); + INIT_DELAYED_WORK(&rt721->jack_btn_check_work, rt721_sdca_btn_check_handler); + + /* + * Mark hw_init to false + * HW init will be performed when device reports present + */ + rt721->hw_init = false; + rt721->first_hw_init = false; + rt721->fu1e_dapm_mute = true; + rt721->fu0f_dapm_mute = true; + rt721->fu0f_mixer_l_mute = rt721->fu0f_mixer_r_mute = true; + rt721->fu1e_mixer_mute[0] = rt721->fu1e_mixer_mute[1] = + rt721->fu1e_mixer_mute[2] = rt721->fu1e_mixer_mute[3] = true; + + return devm_snd_soc_register_component(dev, + &soc_sdca_dev_rt721, rt721_sdca_dai, ARRAY_SIZE(rt721_sdca_dai)); +} + +int rt721_sdca_io_init(struct device *dev, struct sdw_slave *slave) +{ + struct rt721_sdca_priv *rt721 = dev_get_drvdata(dev); + + rt721->disable_irq = false; + + if (rt721->hw_init) + return 0; + + regcache_cache_only(rt721->regmap, false); + regcache_cache_only(rt721->mbq_regmap, false); + if (rt721->first_hw_init) { + regcache_cache_bypass(rt721->regmap, true); + regcache_cache_bypass(rt721->mbq_regmap, true); + } else { + /* + * PM runtime is only enabled when a Slave reports as Attached + */ + + /* set autosuspend parameters */ + pm_runtime_set_autosuspend_delay(&slave->dev, 3000); + pm_runtime_use_autosuspend(&slave->dev); + + /* update count of parent 'active' children */ + pm_runtime_set_active(&slave->dev); + + /* make sure the device does not suspend immediately */ + pm_runtime_mark_last_busy(&slave->dev); + + pm_runtime_enable(&slave->dev); + } + + pm_runtime_get_noresume(&slave->dev); + rt721_sdca_dmic_preset(rt721); + rt721_sdca_amp_preset(rt721); + rt721_sdca_jack_preset(rt721); + if (rt721->first_hw_init) { + regcache_cache_bypass(rt721->regmap, false); + regcache_mark_dirty(rt721->regmap); + regcache_cache_bypass(rt721->mbq_regmap, false); + regcache_mark_dirty(rt721->mbq_regmap); + } else + rt721->first_hw_init = true; + + /* Mark Slave initialization complete */ + rt721->hw_init = true; + + pm_runtime_mark_last_busy(&slave->dev); + pm_runtime_put_autosuspend(&slave->dev); + + dev_dbg(&slave->dev, "%s hw_init complete\n", __func__); + return 0; +} + +MODULE_DESCRIPTION("ASoC RT721 SDCA SDW driver"); +MODULE_AUTHOR("Jack Yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt721-sdca.h b/sound/soc/codecs/rt721-sdca.h new file mode 100644 index 000000000000..e2f071909da8 --- /dev/null +++ b/sound/soc/codecs/rt721-sdca.h @@ -0,0 +1,268 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * rt721-sdca.h -- RT721 SDCA ALSA SoC audio driver header + * + * Copyright(c) 2024 Realtek Semiconductor Corp. + */ + +#ifndef __RT721_H__ +#define __RT721_H__ + +#include <linux/pm.h> +#include <linux/regmap.h> +#include <linux/soundwire/sdw.h> +#include <linux/soundwire/sdw_type.h> +#include <sound/soc.h> +#include <linux/workqueue.h> + +struct rt721_sdca_priv { + struct regmap *regmap; + struct regmap *mbq_regmap; + struct snd_soc_component *component; + struct sdw_slave *slave; + struct sdw_bus_params params; + bool hw_init; + bool first_hw_init; + struct mutex calibrate_mutex; + struct mutex disable_irq_lock; + bool disable_irq; + /* For Headset jack & Headphone */ + unsigned int scp_sdca_stat1; + unsigned int scp_sdca_stat2; + struct snd_soc_jack *hs_jack; + struct delayed_work jack_detect_work; + struct delayed_work jack_btn_check_work; + int jack_type; + int jd_src; + bool fu0f_dapm_mute; + bool fu0f_mixer_l_mute; + bool fu0f_mixer_r_mute; + /* For DMIC */ + bool fu1e_dapm_mute; + bool fu1e_mixer_mute[4]; +}; + +struct rt721_sdca_dmic_kctrl_priv { + unsigned int reg_base; + unsigned int count; + unsigned int max; + unsigned int invert; +}; + +/* NID */ +#define RT721_ANA_POW_PART 0x01 +#define RT721_DAC_CTRL 0x04 +#define RT721_JD_CTRL 0x09 +#define RT721_CBJ_CTRL 0x0a +#define RT721_CAP_PORT_CTRL 0x0c +#define RT721_CLASD_AMP_CTRL 0x0d +#define RT721_VENDOR_REG 0x20 +#define RT721_RC_CALIB_CTRL 0x40 +#define RT721_VENDOR_EQ_L 0x53 +#define RT721_VENDOR_EQ_R 0x54 +#define RT721_VENDOR_HP_CALI 0x56 +#define RT721_VENDOR_CHARGE_PUMP 0x57 +#define RT721_VENDOR_CLASD_CALI 0x58 +#define RT721_VENDOR_IMS_DRE 0x5b +#define RT721_VENDOR_SPK_EFUSE 0x5c +#define RT721_VENDOR_LEVEL_CTRL 0x5d +#define RT721_VENDOR_ANA_CTL 0x5f +#define RT721_HDA_SDCA_FLOAT 0x61 + +/* Index (NID:01h) */ +#define RT721_MBIAS_LV_CTRL2 0x07 +#define RT721_VREF1_HV_CTRL1 0x0a +#define RT721_VREF2_LV_CTRL1 0x0b + +/* Index (NID:04h) */ +#define RT721_DAC_2CH_CTRL3 0x02 +#define RT721_DAC_2CH_CTRL4 0x03 + +/* Index (NID:09h) */ +#define RT721_JD_1PIN_GAT_CTRL2 0x07 + +/* Index (NID:0ah) */ +#define RT721_CBJ_A0_GAT_CTRL1 0x04 +#define RT721_CBJ_A0_GAT_CTRL2 0x05 + +/* Index (NID:0Ch) */ +#define RT721_HP_AMP_2CH_CAL1 0x05 +#define RT721_HP_AMP_2CH_CAL4 0x08 +#define RT721_HP_AMP_2CH_CAL18 0x1b + +/* Index (NID:0dh) */ +#define RT721_CLASD_AMP_2CH_CAL 0x14 + +/* Index (NID:20h) */ +#define RT721_JD_PRODUCT_NUM 0x00 +#define RT721_ANALOG_BIAS_CTL3 0x04 +#define RT721_JD_CTRL1 0x09 +#define RT721_LDO2_3_CTL1 0x0e +#define RT721_GPIO_PAD_CTRL5 0x13 +#define RT721_LDO1_CTL 0x1a +#define RT721_HP_JD_CTRL 0x24 +#define RT721_VD_HIDDEN_CTRL 0x26 +#define RT721_CLSD_CTRL6 0x3c +#define RT721_COMBO_JACK_AUTO_CTL1 0x45 +#define RT721_COMBO_JACK_AUTO_CTL2 0x46 +#define RT721_COMBO_JACK_AUTO_CTL3 0x47 +#define RT721_DIGITAL_MISC_CTRL4 0x4a +#define RT721_VREFO_GAT 0x63 +#define RT721_FSM_CTL 0x67 +#define RT721_SDCA_INTR_REC 0x82 +#define RT721_SW_CONFIG1 0x8a +#define RT721_SW_CONFIG2 0x8b + +/* Index (NID:40h) */ +#define RT721_RC_CALIB_CTRL0 0x00 + +/* Index (NID:58h) */ +#define RT721_DAC_DC_CALI_CTL1 0x01 +#define RT721_DAC_DC_CALI_CTL2 0x02 +#define RT721_DAC_DC_CALI_CTL3 0x03 + +/* Index (NID:5fh) */ +#define RT721_MISC_POWER_CTL0 0x00 +#define RT721_MISC_POWER_CTL31 0x31 +#define RT721_UAJ_TOP_TCON13 0x44 +#define RT721_UAJ_TOP_TCON14 0x45 +#define RT721_UAJ_TOP_TCON17 0x48 + +/* Index (NID:61h) */ +#define RT721_HDA_LEGACY_MUX_CTL0 0x00 +#define RT721_HDA_LEGACY_UAJ_CTL 0x02 +#define RT721_HDA_LEGACY_CTL1 0x05 +#define RT721_HDA_LEGACY_RESET_CTL 0x06 +#define RT721_GE_REL_CTRL1 0x0d +#define RT721_HDA_LEGACY_GPIO_WAKE_EN_CTL 0x0e +#define RT721_GE_SDCA_RST_CTRL 0x10 +#define RT721_INT_RST_EN_CTRL 0x11 +#define RT721_XU_EVENT_EN 0x13 +#define RT721_INLINE_CTL2 0x17 +#define RT721_UMP_HID_CTRL1 0x18 +#define RT721_UMP_HID_CTRL2 0x19 +#define RT721_UMP_HID_CTRL3 0x1a +#define RT721_UMP_HID_CTRL4 0x1b +#define RT721_UMP_HID_CTRL5 0x1c +#define RT721_FUNC_FLOAT_CTL0 0x22 +#define RT721_FUNC_FLOAT_CTL1 0x23 +#define RT721_FUNC_FLOAT_CTL2 0x24 +#define RT721_FUNC_FLOAT_CTL3 0x25 +#define RT721_ENT_FLOAT_CTL0 0x29 +#define RT721_ENT_FLOAT_CTL1 0x2c +#define RT721_ENT_FLOAT_CTL2 0x2d +#define RT721_ENT_FLOAT_CTL3 0x2e +#define RT721_ENT_FLOAT_CTL4 0x2f +#define RT721_CH_FLOAT_CTL1 0x45 +#define RT721_CH_FLOAT_CTL2 0x46 +#define RT721_ENT_FLOAT_CTL5 0x53 +#define RT721_ENT_FLOAT_CTL6 0x54 +#define RT721_ENT_FLOAT_CTL7 0x55 +#define RT721_ENT_FLOAT_CTL8 0x57 +#define RT721_ENT_FLOAT_CTL9 0x5a +#define RT721_ENT_FLOAT_CTL10 0x5b +#define RT721_CH_FLOAT_CTL3 0x6a +#define RT721_CH_FLOAT_CTL4 0x6d +#define RT721_CH_FLOAT_CTL5 0x70 +#define RT721_CH_FLOAT_CTL6 0x92 + +/* Parameter & Verb control 01 (0x26)(NID:20h) */ +#define RT721_HIDDEN_REG_SW_RESET (0x1 << 14) + +/* Buffer address for HID */ +#define RT721_BUF_ADDR_HID1 0x44030000 +#define RT721_BUF_ADDR_HID2 0x44030020 + +/* RT721 SDCA Control - function number */ +#define FUNC_NUM_JACK_CODEC 0x01 +#define FUNC_NUM_MIC_ARRAY 0x02 +#define FUNC_NUM_HID 0x03 +#define FUNC_NUM_AMP 0x04 + +/* RT721 SDCA entity */ +#define RT721_SDCA_ENT_HID01 0x01 +#define RT721_SDCA_ENT_XUV 0x03 +#define RT721_SDCA_ENT_GE49 0x49 +#define RT721_SDCA_ENT_USER_FU05 0x05 +#define RT721_SDCA_ENT_USER_FU06 0x06 +#define RT721_SDCA_ENT_USER_FU0F 0x0f +#define RT721_SDCA_ENT_USER_FU10 0x19 +#define RT721_SDCA_ENT_USER_FU1E 0x1e +#define RT721_SDCA_ENT_FU15 0x15 +#define RT721_SDCA_ENT_PDE23 0x23 +#define RT721_SDCA_ENT_PDE40 0x40 +#define RT721_SDCA_ENT_PDE41 0x41 +#define RT721_SDCA_ENT_PDE11 0x11 +#define RT721_SDCA_ENT_PDE12 0x12 +#define RT721_SDCA_ENT_PDE2A 0x2a +#define RT721_SDCA_ENT_CS01 0x01 +#define RT721_SDCA_ENT_CS11 0x11 +#define RT721_SDCA_ENT_CS1F 0x1f +#define RT721_SDCA_ENT_CS1C 0x1c +#define RT721_SDCA_ENT_CS31 0x31 +#define RT721_SDCA_ENT_OT23 0x42 +#define RT721_SDCA_ENT_IT26 0x26 +#define RT721_SDCA_ENT_IT09 0x09 +#define RT721_SDCA_ENT_PLATFORM_FU15 0x15 +#define RT721_SDCA_ENT_PLATFORM_FU44 0x44 +#define RT721_SDCA_ENT_XU03 0x03 +#define RT721_SDCA_ENT_XU0D 0x0d +#define RT721_SDCA_ENT_FU55 0x55 + +/* RT721 SDCA control */ +#define RT721_SDCA_CTL_SAMPLE_FREQ_INDEX 0x10 +#define RT721_SDCA_CTL_FU_MUTE 0x01 +#define RT721_SDCA_CTL_FU_VOLUME 0x02 +#define RT721_SDCA_CTL_HIDTX_CURRENT_OWNER 0x10 +#define RT721_SDCA_CTL_HIDTX_SET_OWNER_TO_DEVICE 0x11 +#define RT721_SDCA_CTL_HIDTX_MESSAGE_OFFSET 0x12 +#define RT721_SDCA_CTL_HIDTX_MESSAGE_LENGTH 0x13 +#define RT721_SDCA_CTL_SELECTED_MODE 0x01 +#define RT721_SDCA_CTL_DETECTED_MODE 0x02 +#define RT721_SDCA_CTL_REQ_POWER_STATE 0x01 +#define RT721_SDCA_CTL_VENDOR_DEF 0x30 +#define RT721_SDCA_CTL_XUV 0x34 +#define RT721_SDCA_CTL_FU_CH_GAIN 0x0b + +/* RT721 SDCA channel */ +#define CH_L 0x01 +#define CH_R 0x02 +#define CH_01 0x01 +#define CH_02 0x02 +#define CH_03 0x03 +#define CH_04 0x04 +#define CH_08 0x08 +#define CH_09 0x09 +#define CH_0A 0x0a + +/* sample frequency index */ +#define RT721_SDCA_RATE_8000HZ 0x01 +#define RT721_SDCA_RATE_11025HZ 0x02 +#define RT721_SDCA_RATE_12000HZ 0x03 +#define RT721_SDCA_RATE_16000HZ 0x04 +#define RT721_SDCA_RATE_22050HZ 0x05 +#define RT721_SDCA_RATE_24000HZ 0x06 +#define RT721_SDCA_RATE_32000HZ 0x07 +#define RT721_SDCA_RATE_44100HZ 0x08 +#define RT721_SDCA_RATE_48000HZ 0x09 +#define RT721_SDCA_RATE_88200HZ 0x0a +#define RT721_SDCA_RATE_96000HZ 0x0b +#define RT721_SDCA_RATE_176400HZ 0x0c +#define RT721_SDCA_RATE_192000HZ 0x0d +#define RT721_SDCA_RATE_384000HZ 0x0e +#define RT721_SDCA_RATE_768000HZ 0x0f + +/* RT721 HID ID */ +#define RT721_SDCA_HID_ID 0x11 + +enum { + RT721_AIF1, /* For headset mic and headphone */ + RT721_AIF2, /* For speaker */ + RT721_AIF3, /* For dmic */ + RT721_AIFS, +}; + +int rt721_sdca_io_init(struct device *dev, struct sdw_slave *slave); +int rt721_sdca_init(struct device *dev, struct regmap *regmap, + struct regmap *mbq_regmap, struct sdw_slave *slave); +#endif /* __RT721_H__ */ -- 2.34.1

1 0

[PATCH v2] ASoC: rt-sdw-common: Common functions for Realtek soundwire driver
by Jack Yu 01 Oct '24

01 Oct '24

This is the first version of common functions for Realtek soundwire codec driver. Signed-off-by: Jack Yu <jack.yu(a)realtek.com> --- sound/soc/codecs/Kconfig | 5 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/rt-sdw-common.c | 238 +++++++++++++++++++++++++++++++ sound/soc/codecs/rt-sdw-common.h | 66 +++++++++ 4 files changed, 311 insertions(+) create mode 100644 sound/soc/codecs/rt-sdw-common.c create mode 100644 sound/soc/codecs/rt-sdw-common.h diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 7092842480ef..b095eba9d634 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -1545,6 +1545,11 @@ config SND_SOC_RL6231 default m if SND_SOC_RT1305=m default m if SND_SOC_RT1308=m +config SND_SOC_RT_SDW_COMMON + tristate + default y if SND_SOC_RT721_SDCA_SDW=y + default m if SND_SOC_RT721_SDCA_SDW=m + config SND_SOC_RL6347A tristate default y if SND_SOC_RT274=y diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 54cbc3feae32..4497b2e30cd3 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -216,6 +216,7 @@ snd-soc-rk3308-y := rk3308_codec.o snd-soc-rk3328-y := rk3328_codec.o snd-soc-rk817-y := rk817_codec.o snd-soc-rl6231-y := rl6231.o +snd-soc-rt-sdw-common-y := rt-sdw-common.o snd-soc-rl6347a-y := rl6347a.o snd-soc-rt1011-y := rt1011.o snd-soc-rt1015-y := rt1015.o @@ -618,6 +619,7 @@ obj-$(CONFIG_SND_SOC_RK3308) += snd-soc-rk3308.o obj-$(CONFIG_SND_SOC_RK3328) += snd-soc-rk3328.o obj-$(CONFIG_SND_SOC_RK817) += snd-soc-rk817.o obj-$(CONFIG_SND_SOC_RL6231) += snd-soc-rl6231.o +obj-$(CONFIG_SND_SOC_RT_SDW_COMMON) += snd-soc-rt-sdw-common.o obj-$(CONFIG_SND_SOC_RL6347A) += snd-soc-rl6347a.o obj-$(CONFIG_SND_SOC_RT1011) += snd-soc-rt1011.o obj-$(CONFIG_SND_SOC_RT1015) += snd-soc-rt1015.o diff --git a/sound/soc/codecs/rt-sdw-common.c b/sound/soc/codecs/rt-sdw-common.c new file mode 100644 index 000000000000..9ed0e9855699 --- /dev/null +++ b/sound/soc/codecs/rt-sdw-common.c @@ -0,0 +1,238 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt-sdw-common.c +// +// Copyright(c) 2024 Realtek Semiconductor Corp. +// + +/* + * This file defines common functions used with Realtek soundwire codecs. + */ + +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/bitops.h> +#include <linux/soundwire/sdw_registers.h> +#include <sound/jack.h> + +#include "rt-sdw-common.h" + +/** + * rt_sdca_index_write - Write a value to Realtek defined register. + * + * @map: map for setting. + * @nid: Realtek-defined ID. + * @reg: register. + * @value: value. + * + * A value of zero will be returned on success, a negative errno will + * be returned in error cases. + */ +int rt_sdca_index_write(struct regmap *map, unsigned int nid, + unsigned int reg, unsigned int value) +{ + unsigned int addr = (nid << 20) | reg; + int ret; + + ret = regmap_write(map, addr, value); + if (ret < 0) + pr_err("Failed to set value: %06x <= %04x ret=%d\n", + addr, value, ret); + + return ret; +} +EXPORT_SYMBOL_GPL(rt_sdca_index_write); + +/** + * rt_sdca_index_read - Read value from Realtek defined register. + * + * @map: map for setting. + * @nid: Realtek-defined ID. + * @reg: register. + * @value: value. + * + * A value of zero will be returned on success, a negative errno will + * be returned in error cases. + */ +int rt_sdca_index_read(struct regmap *map, unsigned int nid, + unsigned int reg, unsigned int *value) +{ + unsigned int addr = (nid << 20) | reg; + int ret; + + ret = regmap_read(map, addr, value); + if (ret < 0) + pr_err("Failed to get value: %06x => %04x ret=%d\n", + addr, *value, ret); + + return ret; +} +EXPORT_SYMBOL_GPL(rt_sdca_index_read); + +/** + * rt_sdca_index_update_bits - Update value on Realtek defined register. + * + * @map: map for setting. + * @nid: Realtek-defined ID. + * @reg: register. + * @mask: Bitmask to change + * @value: New value for bitmask + * + * A value of zero will be returned on success, a negative errno will + * be returned in error cases. + */ + +int rt_sdca_index_update_bits(struct regmap *map, + unsigned int nid, unsigned int reg, unsigned int mask, unsigned int val) +{ + unsigned int tmp; + int ret; + + ret = rt_sdca_index_read(map, nid, reg, &tmp); + if (ret < 0) + return ret; + + set_mask_bits(&tmp, mask, val); + return rt_sdca_index_write(map, nid, reg, tmp); +} +EXPORT_SYMBOL_GPL(rt_sdca_index_update_bits); + +/** + * rt_sdca_btn_type - Decision of button type. + * + * @buffer: UMP message buffer. + * + * A button type will be returned regarding to buffer, + * it returns zero if buffer cannot be recognized. + */ +int rt_sdca_btn_type(unsigned char *buffer) +{ + u8 btn_type = 0; + int ret; + + btn_type |= buffer[0] & 0xf; + btn_type |= (buffer[0] >> 4) & 0xf; + btn_type |= buffer[1] & 0xf; + btn_type |= (buffer[1] >> 4) & 0xf; + + if (btn_type & BIT(0)) + ret |= SND_JACK_BTN_2; + if (btn_type & BIT(1)) + ret |= SND_JACK_BTN_3; + if (btn_type & BIT(2)) + ret |= SND_JACK_BTN_0; + if (btn_type & BIT(3)) + ret |= SND_JACK_BTN_1; + + return ret; +} +EXPORT_SYMBOL_GPL(rt_sdca_btn_type); + +/** + * rt_sdca_headset_detect - Headset jack type detection. + * + * @map: map for setting. + * @entity_id: SDCA entity ID. + * + * A headset jack type will be returned, a negative errno will + * be returned in error cases. + */ +int rt_sdca_headset_detect(struct regmap *map, unsigned int entity_id) +{ + unsigned int det_mode, jack_type; + int ret; + + /* get detected_mode */ + ret = regmap_read(map, SDW_SDCA_CTL(SDCA_NUM_JACK_CODEC, entity_id, + RT_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + + if (ret < 0) + goto io_error; + + switch (det_mode) { + case 0x00: + jack_type = 0; + break; + case 0x03: + jack_type = SND_JACK_HEADPHONE; + break; + case 0x05: + jack_type = SND_JACK_HEADSET; + break; + } + + /* write selected_mode */ + if (det_mode) { + ret = regmap_write(map, SDW_SDCA_CTL(SDCA_NUM_JACK_CODEC, entity_id, + RT_SDCA_CTL_SELECTED_MODE, 0), det_mode); + if (ret < 0) + goto io_error; + } + + return jack_type; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} +EXPORT_SYMBOL_GPL(rt_sdca_headset_detect); + +/** + * rt_sdca_button_detect - Read UMP message and decide button type. + * + * @map: map for setting. + * @entity_id: SDCA entity ID. + * @hid_buf_addr: HID buffer address. + * @hid_id: Report ID for HID. + * + * A button type will be returned regarding to buffer, + * it returns zero if buffer cannot be recognized. + */ +int rt_sdca_button_detect(struct regmap *map, unsigned int entity_id, + unsigned int hid_buf_addr, unsigned int hid_id) +{ + unsigned int btn_type = 0, offset, idx, val, owner; + unsigned char buf[3]; + int ret; + + /* get current UMP message owner */ + ret = regmap_read(map, SDW_SDCA_CTL(SDCA_NUM_HID, entity_id, + RT_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), &owner); + if (ret < 0) + return 0; + + /* if owner is device then there is no button event from device */ + if (owner == 1) + return 0; + + /* read UMP message offset */ + ret = regmap_read(map, SDW_SDCA_CTL(SDCA_NUM_HID, entity_id, + RT_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto _end_btn_det_; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(map, hid_buf_addr + offset + idx, &val); + if (ret < 0) + goto _end_btn_det_; + buf[idx] = val & 0xff; + } + /* Report ID for HID */ + if (buf[0] == hid_id) + btn_type = rt_sdca_btn_type(&buf[1]); + +_end_btn_det_: + /* Host is owner, so set back to device */ + if (owner == 0) + /* set owner to device */ + regmap_write(map, + SDW_SDCA_CTL(SDCA_NUM_HID, entity_id, + RT_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), 0x01); + + return btn_type; +} +EXPORT_SYMBOL_GPL(rt_sdca_button_detect); + +MODULE_DESCRIPTION("Realtek soundwire common functions"); +MODULE_AUTHOR("jack yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt-sdw-common.h b/sound/soc/codecs/rt-sdw-common.h new file mode 100644 index 000000000000..4759516feb38 --- /dev/null +++ b/sound/soc/codecs/rt-sdw-common.h @@ -0,0 +1,66 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +// +// rt-sdw-common.h +// +// Copyright(c) 2024 Realtek Semiconductor Corp. +// + +/* + * This file defines common functions used with Realtek soundwire codecs. + */ + +#ifndef __RT_SDW_COMMON_H__ +#define __RT_SDW_COMMON_H__ + +#define SDCA_NUM_JACK_CODEC 0x01 +#define SDCA_NUM_MIC_ARRAY 0x02 +#define SDCA_NUM_HID 0x03 +#define SDCA_NUM_AMP 0x04 +#define RT_SDCA_CTL_SELECTED_MODE 0x01 +#define RT_SDCA_CTL_DETECTED_MODE 0x02 +#define RT_SDCA_CTL_HIDTX_CURRENT_OWNER 0x10 +#define RT_SDCA_CTL_HIDTX_MESSAGE_OFFSET 0x12 + +struct rt_sdca_dmic_kctrl_priv { + unsigned int reg_base; + unsigned int count; + unsigned int max; + unsigned int invert; +}; + +#define RT_SDCA_PR_VALUE(xreg_base, xcount, xmax, xinvert) \ + ((unsigned long)&(struct rt_sdca_dmic_kctrl_priv) \ + {.reg_base = xreg_base, .count = xcount, .max = xmax, \ + .invert = xinvert}) + +#define RT_SDCA_FU_CTRL(xname, reg_base, xmax, xinvert, xcount, \ + xinfo, xget, xput) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .info = xinfo, \ + .get = xget, \ + .put = xput, \ + .private_value = RT_SDCA_PR_VALUE(reg_base, xcount, xmax, xinvert)} + +#define RT_SDCA_EXT_TLV(xname, reg_base, xhandler_get,\ + xhandler_put, xcount, xmax, tlv_array, xinfo) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ | \ + SNDRV_CTL_ELEM_ACCESS_READWRITE, \ + .tlv.p = (tlv_array), \ + .info = xinfo, \ + .get = xhandler_get, .put = xhandler_put, \ + .private_value = RT_SDCA_PR_VALUE(reg_base, xcount, xmax, 0) } + + +int rt_sdca_index_write(struct regmap *map, unsigned int nid, + unsigned int reg, unsigned int value); +int rt_sdca_index_read(struct regmap *map, unsigned int nid, + unsigned int reg, unsigned int *value); +int rt_sdca_index_update_bits(struct regmap *map, + unsigned int nid, unsigned int reg, unsigned int mask, unsigned int val); +int rt_sdca_btn_type(unsigned char *buffer); +int rt_sdca_headset_detect(struct regmap *map, unsigned int entity_id); +int rt_sdca_button_detect(struct regmap *map, unsigned int entity_id, + unsigned int hid_buf_addr, unsigned int hid_id); + +#endif /* __RT_SDW_COMMON_H__ */ -- 2.34.1

1 0

[PATCH] ASoC: rt-sdw-common: Common functions for Realtek soundwire driver
by Jack Yu 01 Oct '24

01 Oct '24

This is the first version of common functions for Realtek soundwire codec driver. Signed-off-by: Jack Yu <jack.yu(a)realtek.com> --- sound/soc/codecs/Kconfig | 5 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/rt-sdw-common.c | 241 +++++++++++++++++++++++++++++++ sound/soc/codecs/rt-sdw-common.h | 67 +++++++++ 4 files changed, 315 insertions(+) create mode 100644 sound/soc/codecs/rt-sdw-common.c create mode 100644 sound/soc/codecs/rt-sdw-common.h diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig index 7092842480ef..b095eba9d634 100644 --- a/sound/soc/codecs/Kconfig +++ b/sound/soc/codecs/Kconfig @@ -1545,6 +1545,11 @@ config SND_SOC_RL6231 default m if SND_SOC_RT1305=m default m if SND_SOC_RT1308=m +config SND_SOC_RT_SDW_COMMON + tristate + default y if SND_SOC_RT721_SDCA_SDW=y + default m if SND_SOC_RT721_SDCA_SDW=m + config SND_SOC_RL6347A tristate default y if SND_SOC_RT274=y diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile index 54cbc3feae32..4497b2e30cd3 100644 --- a/sound/soc/codecs/Makefile +++ b/sound/soc/codecs/Makefile @@ -216,6 +216,7 @@ snd-soc-rk3308-y := rk3308_codec.o snd-soc-rk3328-y := rk3328_codec.o snd-soc-rk817-y := rk817_codec.o snd-soc-rl6231-y := rl6231.o +snd-soc-rt-sdw-common-y := rt-sdw-common.o snd-soc-rl6347a-y := rl6347a.o snd-soc-rt1011-y := rt1011.o snd-soc-rt1015-y := rt1015.o @@ -618,6 +619,7 @@ obj-$(CONFIG_SND_SOC_RK3308) += snd-soc-rk3308.o obj-$(CONFIG_SND_SOC_RK3328) += snd-soc-rk3328.o obj-$(CONFIG_SND_SOC_RK817) += snd-soc-rk817.o obj-$(CONFIG_SND_SOC_RL6231) += snd-soc-rl6231.o +obj-$(CONFIG_SND_SOC_RT_SDW_COMMON) += snd-soc-rt-sdw-common.o obj-$(CONFIG_SND_SOC_RL6347A) += snd-soc-rl6347a.o obj-$(CONFIG_SND_SOC_RT1011) += snd-soc-rt1011.o obj-$(CONFIG_SND_SOC_RT1015) += snd-soc-rt1015.o diff --git a/sound/soc/codecs/rt-sdw-common.c b/sound/soc/codecs/rt-sdw-common.c new file mode 100644 index 000000000000..e758567e9c58 --- /dev/null +++ b/sound/soc/codecs/rt-sdw-common.c @@ -0,0 +1,241 @@ +// SPDX-License-Identifier: GPL-2.0-only +// +// rt-sdw-common.c +// +// Copyright(c) 2024 Realtek Semiconductor Corp. +// + +/* + * This file defines common functions used with Realtek soundwire codecs. + */ + +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/bitops.h> +#include <linux/soundwire/sdw_registers.h> +#include <sound/jack.h> + +#include "rt-sdw-common.h" + +/** + * rt_sdca_index_write - Write a value to Realtek defined register. + * + * @map: map for setting. + * @nid: Realtek-defined ID. + * @reg: register. + * @value: value. + * + * A value of zero will be returned on success, a negative errno will + * be returned in error cases. + */ +int rt_sdca_index_write(struct regmap *map, unsigned int nid, + unsigned int reg, unsigned int value) +{ + unsigned int addr = (nid << 20) | reg; + int ret; + + ret = regmap_write(map, addr, value); + if (ret < 0) + pr_err("Failed to set value: %06x <= %04x ret=%d\n", + addr, value, ret); + + return ret; +} +EXPORT_SYMBOL_GPL(rt_sdca_index_write); + +/** + * rt_sdca_index_read - Read value from Realtek defined register. + * + * @map: map for setting. + * @nid: Realtek-defined ID. + * @reg: register. + * @value: value. + * + * A value of zero will be returned on success, a negative errno will + * be returned in error cases. + */ +int rt_sdca_index_read(struct regmap *map, unsigned int nid, + unsigned int reg, unsigned int *value) +{ + unsigned int addr = (nid << 20) | reg; + int ret; + + ret = regmap_read(map, addr, value); + if (ret < 0) + pr_err("Failed to get value: %06x => %04x ret=%d\n", + addr, *value, ret); + + return ret; +} +EXPORT_SYMBOL_GPL(rt_sdca_index_read); + +/** + * rt_sdca_index_update_bits - Update value on Realtek defined register. + * + * @map: map for setting. + * @nid: Realtek-defined ID. + * @reg: register. + * @mask: Bitmask to change + * @value: New value for bitmask + * + * A value of zero will be returned on success, a negative errno will + * be returned in error cases. + */ + +int rt_sdca_index_update_bits(struct regmap *map, + unsigned int nid, unsigned int reg, unsigned int mask, unsigned int val) +{ + unsigned int tmp; + int ret; + + ret = rt_sdca_index_read(map, nid, reg, &tmp); + if (ret < 0) + return ret; + + set_mask_bits(&tmp, mask, val); + return rt_sdca_index_write(map, nid, reg, tmp); +} +EXPORT_SYMBOL_GPL(rt_sdca_index_update_bits); + +/** + * rt_sdca_btn_type - Decision of button type. + * + * @buffer: UMP message buffer. + * + * A button type will be returned regarding to buffer, + * it returns zero if buffer cannot be recognized. + */ +int rt_sdca_btn_type(unsigned char *buffer) +{ + u8 btn_type = 0; + int ret; + + btn_type |= buffer[0] & 0xf; + btn_type |= (buffer[0] >> 4) & 0xf; + btn_type |= buffer[1] & 0xf; + btn_type |= (buffer[1] >> 4) & 0xf; + + if (btn_type & BIT(0)) + ret |= SND_JACK_BTN_2; + if (btn_type & BIT(1)) + ret |= SND_JACK_BTN_3; + if (btn_type & BIT(2)) + ret |= SND_JACK_BTN_0; + if (btn_type & BIT(3)) + ret |= SND_JACK_BTN_1; + + return ret; +} +EXPORT_SYMBOL_GPL(rt_sdca_btn_type); + +/** + * rt_sdca_headset_detect - Headset jack type detection. + * + * @map: map for setting. + * @entity_id: SDCA entity ID. + * + * A headset jack type will be returned, a negative errno will + * be returned in error cases. + */ +int rt_sdca_headset_detect(struct regmap *map, unsigned int entity_id) +{ + unsigned int det_mode, jack_type; + int ret; + + /* get detected_mode */ + ret = regmap_read(map, SDW_SDCA_CTL(SDCA_NUM_JACK_CODEC, entity_id, + RT_SDCA_CTL_DETECTED_MODE, 0), &det_mode); + + if (ret < 0) + goto io_error; + + switch (det_mode) { + case 0x00: + jack_type = 0; + break; + case 0x03: + jack_type = SND_JACK_HEADPHONE; + break; + case 0x05: + jack_type = SND_JACK_HEADSET; + break; + } + + /* write selected_mode */ + if (det_mode) { + ret = regmap_write(map, SDW_SDCA_CTL(SDCA_NUM_JACK_CODEC, entity_id, + RT_SDCA_CTL_SELECTED_MODE, 0), det_mode); + if (ret < 0) + goto io_error; + } + + return jack_type; + +io_error: + pr_err_ratelimited("IO error in %s, ret %d\n", __func__, ret); + return ret; +} +EXPORT_SYMBOL_GPL(rt_sdca_headset_detect); + +/** + * rt_sdca_button_detect - Read UMP message and decide button type. + * + * @map: map for setting. + * @entity_id: SDCA entity ID. + * @hid_buf_addr: HID buffer address. + * @hid_id: Report ID for HID. + * @mask1: Mask for button message. + * @mask2: Mask for button message. + * + * A button type will be returned regarding to buffer, + * it returns zero if buffer cannot be recognized. + */ +int rt_sdca_button_detect(struct regmap *map, unsigned int entity_id, + unsigned int hid_buf_addr, unsigned int hid_id, + unsigned int mask1, unsigned int mask2) +{ + unsigned int btn_type = 0, offset, idx, val, owner; + unsigned char buf[3]; + int ret; + + /* get current UMP message owner */ + ret = regmap_read(map, SDW_SDCA_CTL(SDCA_NUM_HID, entity_id, + RT_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), &owner); + if (ret < 0) + return 0; + + /* if owner is device then there is no button event from device */ + if (owner == 1) + return 0; + + /* read UMP message offset */ + ret = regmap_read(map, SDW_SDCA_CTL(SDCA_NUM_HID, entity_id, + RT_SDCA_CTL_HIDTX_MESSAGE_OFFSET, 0), &offset); + if (ret < 0) + goto _end_btn_det_; + + for (idx = 0; idx < sizeof(buf); idx++) { + ret = regmap_read(map, hid_buf_addr + offset + idx, &val); + if (ret < 0) + goto _end_btn_det_; + buf[idx] = val & 0xff; + } + /* Report ID for HID */ + if (buf[0] == hid_id) + btn_type = rt_sdca_btn_type(&buf[1]); + +_end_btn_det_: + /* Host is owner, so set back to device */ + if (owner == 0) + /* set owner to device */ + regmap_write(map, + SDW_SDCA_CTL(SDCA_NUM_HID, entity_id, + RT_SDCA_CTL_HIDTX_CURRENT_OWNER, 0), 0x01); + + return btn_type; +} +EXPORT_SYMBOL_GPL(rt_sdca_button_detect); + +MODULE_DESCRIPTION("Realtek soundwire common functions"); +MODULE_AUTHOR("jack yu <jack.yu(a)realtek.com>"); +MODULE_LICENSE("GPL"); diff --git a/sound/soc/codecs/rt-sdw-common.h b/sound/soc/codecs/rt-sdw-common.h new file mode 100644 index 000000000000..09e5ffd4fb9e --- /dev/null +++ b/sound/soc/codecs/rt-sdw-common.h @@ -0,0 +1,67 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +// +// rt-sdw-common.h +// +// Copyright(c) 2024 Realtek Semiconductor Corp. +// + +/* + * This file defines common functions used with Realtek soundwire codecs. + */ + +#ifndef __RT_SDW_COMMON_H__ +#define __RT_SDW_COMMON_H__ + +#define SDCA_NUM_JACK_CODEC 0x01 +#define SDCA_NUM_MIC_ARRAY 0x02 +#define SDCA_NUM_HID 0x03 +#define SDCA_NUM_AMP 0x04 +#define RT_SDCA_CTL_SELECTED_MODE 0x01 +#define RT_SDCA_CTL_DETECTED_MODE 0x02 +#define RT_SDCA_CTL_HIDTX_CURRENT_OWNER 0x10 +#define RT_SDCA_CTL_HIDTX_MESSAGE_OFFSET 0x12 + +struct rt_sdca_dmic_kctrl_priv { + unsigned int reg_base; + unsigned int count; + unsigned int max; + unsigned int invert; +}; + +#define RT_SDCA_PR_VALUE(xreg_base, xcount, xmax, xinvert) \ + ((unsigned long)&(struct rt_sdca_dmic_kctrl_priv) \ + {.reg_base = xreg_base, .count = xcount, .max = xmax, \ + .invert = xinvert}) + +#define RT_SDCA_FU_CTRL(xname, reg_base, xmax, xinvert, xcount, \ + xinfo, xget, xput) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .info = xinfo, \ + .get = xget, \ + .put = xput, \ + .private_value = RT_SDCA_PR_VALUE(reg_base, xcount, xmax, xinvert)} + +#define RT_SDCA_EXT_TLV(xname, reg_base, xhandler_get,\ + xhandler_put, xcount, xmax, tlv_array, xinfo) \ +{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ + .access = SNDRV_CTL_ELEM_ACCESS_TLV_READ | \ + SNDRV_CTL_ELEM_ACCESS_READWRITE, \ + .tlv.p = (tlv_array), \ + .info = xinfo, \ + .get = xhandler_get, .put = xhandler_put, \ + .private_value = RT_SDCA_PR_VALUE(reg_base, xcount, xmax, 0) } + + +int rt_sdca_index_write(struct regmap *map, unsigned int nid, + unsigned int reg, unsigned int value); +int rt_sdca_index_read(struct regmap *map, unsigned int nid, + unsigned int reg, unsigned int *value); +int rt_sdca_index_update_bits(struct regmap *map, + unsigned int nid, unsigned int reg, unsigned int mask, unsigned int val); +int rt_sdca_btn_type(unsigned char *buffer); +int rt_sdca_headset_detect(struct regmap *map, unsigned int entity_id); +int rt_sdca_button_detect(struct regmap *map, unsigned int entity_id, + unsigned int hid_buf_addr, unsigned int hid_id, + unsigned int mask1, unsigned int mask2); + +#endif /* __RT_SDW_COMMON_H__ */ -- 2.34.1

1 0

[PATCH v3 00/13] ASoC: remove dpcm_xxx flags
by Kuninori Morimoto 01 Oct '24

01 Oct '24

Hi Mark This is v3 patch-set Now, we don't need to use dpcm_playback/capture flags for DPCM since v6.11, and thus we can use playback/capture_only flags instead too for DPCM, which is same as non-DPCM. Let's remove dpcm_playback/capture flags, and use playback/capture_only flags instead. [Before] [After] dpcm_playback = 1; /* no setting is needed */ dpcm_capture = 1; dpcm_playback = 1; playback_only = 1; dpcm_capture = 0; dpcm_playback = 0; capture_only = 1; dpcm_capture = 1; And then, because no-one uses dpcm_xxx flags, we don't need to have the code for both DPCM and non-DPCM. These can be handled by same code. This patch-set is based on latest linus/master branch. v2 -> v3 - tidyup Intel files v1 -> v2 - rebased on v6.12-rc1 - tidyup flag handling for sof Link: https://lore.kernel.org/r/87r091lwhg.wl-kuninori.morimoto.gx@renesas.com Link: https://lore.kernel.org/r/87r0979uhx.wl-kuninori.morimoto.gx@renesas.com Kuninori Morimoto (13): ASoC: amd: remove dpcm_xxx flags ASoC: fsl: remove dpcm_xxx flags ASoC: sof: remove dpcm_xxx flags ASoC: intel: remove dpcm_xxx flags ASoC: samsung: remove dpcm_xxx flags ASoC: mediatek: remove dpcm_xxx flags ASoC: soc-core: remove dpcm_xxx flags ASoC: soc-compress: remove dpcm_xxx flags ASoC: soc-topology: remove dpcm_xxx flags ASoC: intel: boards: remove dpcm_xxx flags ASoC: soc-pcm: remove dpcm_xxx flags ASoC: doc: remove dpcm_xxx flags ASoC: soc-pcm: merge DPCM and non-DPCM validation check Documentation/sound/soc/dpcm.rst | 11 +-- include/sound/soc.h | 5 - sound/soc/amd/acp-da7219-max98357a.c | 20 ++-- sound/soc/amd/acp-es8336.c | 2 - sound/soc/amd/acp/acp-mach-common.c | 24 ++--- sound/soc/amd/acp3x-rt5682-max9836.c | 6 +- sound/soc/amd/vangogh/acp5x-mach.c | 6 -- sound/soc/fsl/fsl-asoc-card.c | 24 ++--- sound/soc/fsl/imx-audmix.c | 18 ++-- sound/soc/fsl/imx-card.c | 4 +- sound/soc/intel/avs/boards/da7219.c | 2 - sound/soc/intel/avs/boards/dmic.c | 4 +- sound/soc/intel/avs/boards/es8336.c | 2 - sound/soc/intel/avs/boards/hdaudio.c | 4 - sound/soc/intel/avs/boards/i2s_test.c | 2 - sound/soc/intel/avs/boards/max98357a.c | 2 +- sound/soc/intel/avs/boards/max98373.c | 2 - sound/soc/intel/avs/boards/max98927.c | 2 - sound/soc/intel/avs/boards/nau8825.c | 2 - sound/soc/intel/avs/boards/rt274.c | 2 - sound/soc/intel/avs/boards/rt286.c | 2 - sound/soc/intel/avs/boards/rt298.c | 2 - sound/soc/intel/avs/boards/rt5514.c | 2 +- sound/soc/intel/avs/boards/rt5663.c | 2 - sound/soc/intel/avs/boards/rt5682.c | 2 - sound/soc/intel/avs/boards/ssm4567.c | 2 - sound/soc/intel/boards/bdw-rt5650.c | 4 - sound/soc/intel/boards/bdw-rt5677.c | 4 - sound/soc/intel/boards/bdw_rt286.c | 10 +- sound/soc/intel/boards/bytcht_cx2072x.c | 6 +- sound/soc/intel/boards/bytcht_da7213.c | 6 +- sound/soc/intel/boards/bytcht_es8316.c | 6 +- sound/soc/intel/boards/bytcht_nocodec.c | 6 +- sound/soc/intel/boards/bytcr_rt5640.c | 6 +- sound/soc/intel/boards/bytcr_rt5651.c | 6 +- sound/soc/intel/boards/bytcr_wm5102.c | 6 +- sound/soc/intel/boards/cht_bsw_max98090_ti.c | 6 +- sound/soc/intel/boards/cht_bsw_nau8824.c | 6 +- sound/soc/intel/boards/cht_bsw_rt5645.c | 6 +- sound/soc/intel/boards/cht_bsw_rt5672.c | 6 +- sound/soc/intel/boards/ehl_rt5660.c | 14 ++- sound/soc/intel/boards/hsw_rt5640.c | 10 +- sound/soc/intel/boards/sof_board_helpers.c | 15 +-- sound/soc/intel/boards/sof_es8336.c | 8 +- sound/soc/intel/boards/sof_pcm512x.c | 9 +- sound/soc/intel/boards/sof_wm8804.c | 2 - sound/soc/mediatek/mt2701/mt2701-cs42448.c | 20 +--- sound/soc/mediatek/mt2701/mt2701-wm8960.c | 6 +- sound/soc/mediatek/mt6797/mt6797-mt6351.c | 24 ++--- sound/soc/mediatek/mt7986/mt7986-wm8960.c | 6 +- sound/soc/mediatek/mt8173/mt8173-max98090.c | 6 +- .../mediatek/mt8173/mt8173-rt5650-rt5514.c | 6 +- .../mediatek/mt8173/mt8173-rt5650-rt5676.c | 10 +- sound/soc/mediatek/mt8173/mt8173-rt5650.c | 10 +- .../mediatek/mt8183/mt8183-da7219-max98357.c | 34 +++---- .../mt8183/mt8183-mt6358-ts3a227-max98357.c | 34 +++---- sound/soc/mediatek/mt8186/mt8186-mt6366.c | 86 +++++++---------- sound/soc/mediatek/mt8188/mt8188-mt6359.c | 58 ++++++------ .../mt8192/mt8192-mt6359-rt1015-rt5682.c | 78 +++++++--------- sound/soc/mediatek/mt8195/mt8195-mt6359.c | 60 ++++++------ sound/soc/mediatek/mt8365/mt8365-mt6357.c | 14 +-- sound/soc/samsung/odroid.c | 10 +- sound/soc/soc-compress.c | 15 ++- sound/soc/soc-core.c | 20 +--- sound/soc/soc-pcm.c | 93 +++++++------------ sound/soc/soc-topology-test.c | 2 - sound/soc/soc-topology.c | 4 +- sound/soc/sof/nocodec.c | 7 +- 68 files changed, 318 insertions(+), 583 deletions(-) -- 2.43.0

1 13