October 2024 - Alsa-devel - mailman.alsa-project.org

[PATCH v4 0/9] ASoC: samsung: midas-audio: Add GPIO-based headset jack detection
by Artur Weber 29 Dec '24

29 Dec '24

Many of Samsung's Exynos 4 devices share the same midas-audio driver to handle the codec setup. While most of these devices, including the Midas itself, use the jack detection provided by the WM8994 driver, other devices such as the Samsung Galaxy Tab 3 8.0 (lt01) use two GPIOs and an ADC channel to determine jack insertion, the jack's type, and button presses (for headsets with volume up/down/play buttons). In the downstream kernel, this behavior is implemented in the sec-jack driver[1], and the per-device settings are configured in *-jack.c files in the mach folder (see e.g. the Tab 3's implementation[2]). This patchset implements this mechanism in the midas_wm1811.c driver, and adds new DTS options to allow for its configuration. It also enables jack detection for the Samsung Galaxy Tab 3 8.0. A very similar mechanism was already present in the aries_wm8994.c driver[3]; this implementation heavily borrows from it, though there are a few extra cleanups as well. Signed-off-by: Artur Weber <aweber.kernel(a)gmail.com> [1] https://github.com/gr8nole/android_kernel_samsung_smdk4x12/blob/lineage-14.… [2] https://github.com/gr8nole/android_kernel_samsung_smdk4x12/blob/lineage-14.… [3] https://github.com/torvalds/linux/blob/master/sound/soc/samsung/aries_wm899… --- Changes in v4: - Replaced manual regulator toggles with SND_SOC_DAPM_REGULATOR_SUPPLY, both for existing mic bias regulators and for the new headset mic bias regulator - Link to v3: https://lore.kernel.org/r/20240519-midas-wm1811-gpio-jack-v3-0-0c1736144c0e… Changes in v3: - Re-added pipe (|) character to samsung,headset-button-threshold-microvolt description to prevent it from being parsed as a mapping (fixes syntax error) - Split out "ASoC: dt-bindings: samsung,midas-audio: Add GPIO-based headset jack detection" into two patches - Link to v2: https://lore.kernel.org/r/20240508-midas-wm1811-gpio-jack-v2-0-b4d36cd02c6e… Changes in v2: - Added vendor prefix to threshold properties - Added separate headset mic bias regulator - Changed some cases of dev_err + return with return dev_err_probe - Added an extra patch to replace some previous dev_err + return cases with dev_err_probe - Moved tab3 DTS wm1811 codec config changes to separate commit --- Artur Weber (9): ASoC: dt-bindings: samsung,midas-audio: Add headset mic bias supply ASoC: dt-bindings: samsung,midas-audio: Add GPIO-based headset jack detection ASoC: samsung: midas_wm1811: Use SND_SOC_DAPM_REGULATOR_SUPPLY for bias regulators ASoC: samsung: midas_wm1811: Add headset mic bias supply support ASoC: samsung: midas_wm1811: Add GPIO-based headset jack detection ASoC: samsung: midas_wm1811: Use dev_err_probe where appropriate ARM: dts: samsung: exynos4212-tab3: Fix headset mic, add jack detection ARM: dts: samsung: exynos4212-tab3: Add MCLK2 clock to WM1811 codec config ARM: dts: samsung: exynos4212-tab3: Drop interrupt from WM1811 codec .../bindings/sound/samsung,midas-audio.yaml | 33 ++ arch/arm/boot/dts/samsung/exynos4212-tab3.dtsi | 31 +- sound/soc/samsung/Kconfig | 2 +- sound/soc/samsung/midas_wm1811.c | 348 +++++++++++++++++---- 4 files changed, 343 insertions(+), 71 deletions(-) --- base-commit: a38297e3fb012ddfa7ce0321a7e5a8daeb1872b6 change-id: 20240502-midas-wm1811-gpio-jack-b10226b17ecc Best regards, -- Artur Weber <aweber.kernel(a)gmail.com>

3 12

[PATCH 00/35] Reorganize kerneldoc parameter names
by Julia Lawall 20 Dec '24

20 Dec '24

Reorganize kerneldoc parameter names to match the parameter order in the function header. The misordered cases were identified using the following Coccinelle semantic patch: // <smpl> @initialize:ocaml@ @@ let parse_doc l = let pieces = List.map String.trim (String.split_on_char '*' l) in let l = String.concat " " pieces in match String.split_on_char ':' l with x::xs -> x | _ -> "" let params ps = List.rev (List.fold_left (fun prev (pm,_) -> let ty = String.trim(Pretty_print_c.string_of_fullType pm.Ast_c.p_type) in if ty = "void" && pm.Ast_c.p_namei = None then prev else let name = match pm.Ast_c.p_namei with Some name -> name | None -> failwith "function parameter has no name" in (String.trim (Pretty_print_c.string_of_name name),ty)::prev) [] ps) @r@ comments c; identifier fn; position p; parameter list ps; type T; @@ T@c fn@p(ps) { ... } @script:ocaml@ p << r.p; c << r.c; (_,ps) << r.ps; @@ let isdoc c ps = List.length ps > 1 && (let c = String.trim c in String.length c > 3 && String.sub c 0 3 = "/**" && String.get c 3 != '*') in let subset l1 l2 = List.for_all (fun x -> List.mem x l2) l1 in let (cb,cm,ca) = List.hd c in match List.rev cb with c::_ when isdoc c ps -> let pieces = String.split_on_char '@' c in (match pieces with _::tl -> let d_names = List.map parse_doc tl in (* check parameters *) let p_names = List.map fst (params ps) in if d_names <> [] && not(d_names = p_names) then begin if List.sort compare d_names = List.sort compare p_names then Coccilib.print_main "out of order" p else if subset d_names p_names then Coccilib.print_main "doc is missing a parameter" p else if subset d_names p_names then Coccilib.print_main "doc has an extra parameter" p end | _ -> ()) | _ -> () // </smpl> --- arch/arm/mach-omap2/prm2xxx_3xxx.c | 1 - arch/powerpc/platforms/ps3/interrupt.c | 2 +- arch/powerpc/platforms/ps3/repository.c | 2 +- drivers/base/firmware_loader/main.c | 2 +- drivers/comedi/drivers/comedi_8254.c | 2 +- drivers/gpu/drm/amd/amdgpu/amdgpu_vm.c | 2 +- drivers/gpu/drm/amd/display/dc/core/dc.c | 2 +- drivers/gpu/drm/drm_gem_framebuffer_helper.c | 3 +-- drivers/gpu/drm/drm_gpuvm.c | 2 +- drivers/gpu/drm/radeon/radeon_ib.c | 2 +- drivers/iommu/iommu.c | 2 +- drivers/leds/leds-gpio-register.c | 2 +- drivers/mfd/atmel-smc.c | 4 ++-- drivers/misc/mei/bus.c | 2 +- drivers/mtd/ubi/eba.c | 2 +- drivers/net/ethernet/broadcom/bnxt/bnxt_hwrm.c | 2 +- drivers/net/ethernet/intel/e1000/e1000_hw.c | 2 +- drivers/net/ethernet/intel/i40e/i40e_common.c | 7 +++---- drivers/net/ethernet/intel/ice/ice_common.c | 2 +- drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 2 +- drivers/nvdimm/dimm_devs.c | 2 +- drivers/pci/hotplug/pci_hotplug_core.c | 2 +- drivers/pinctrl/pinmux.c | 2 +- drivers/slimbus/messaging.c | 2 +- drivers/soc/qcom/qmi_interface.c | 2 +- drivers/soundwire/stream.c | 2 +- drivers/usb/gadget/config.c | 4 ++-- fs/char_dev.c | 2 +- fs/dcache.c | 4 ++-- fs/seq_file.c | 2 +- kernel/audit.c | 2 +- kernel/resource.c | 2 +- kernel/sysctl.c | 1 - kernel/trace/ring_buffer.c | 2 +- lib/lru_cache.c | 2 +- lib/maple_tree.c | 2 +- mm/mmu_notifier.c | 2 +- net/dccp/feat.c | 2 +- net/mac80211/mesh_hwmp.c | 6 +++--- net/mac80211/mesh_pathtbl.c | 10 +++++----- net/socket.c | 2 +- net/sunrpc/xprt.c | 2 +- net/tipc/link.c | 14 +++++++------- net/tipc/msg.c | 2 +- sound/pci/hda/hda_codec.c | 2 +- 45 files changed, 60 insertions(+), 64 deletions(-)

4 5

hda: how to implement component master_unbind?
by Kai Vehmanen 20 Dec '24

20 Dec '24

Hi Takashi et al, I've been having multiple discussions with our i915 team w.r.t. audio driver behaviour when the aggregate component is unbound, triggered by i915 unbind. This came up again in the recent regression with devres allocations and I now dug into the topic again. In short, I'm puzzled how to really implement this. ALSA (or ASoC) don't really have support for individual components of a card disappearing in a hotplug fashion. At card level, we do have such support (USB, firewire and recent work for PCI hotplug). But not individual components of a card getting unplugged. In current code we have this: static void hdac_component_master_unbind(struct device *dev) { » struct drm_audio_component *acomp = hdac_get_acomp(dev); » if (acomp->audio_ops && acomp->audio_ops->master_unbind) » » acomp->audio_ops->master_unbind(dev, acomp); » module_put(acomp->ops->owner); » component_unbind_all(dev, acomp); » WARN_ON(acomp->ops || acomp->dev); } ... when e.g. i915 driver is unbound (but could be any driver using the component framework, not jus Intel hw), i915 calls component_del() and HDA gets call to the above. After this, acomp ops are null are audio no longer has ability to talk to i915 driver (which makes sense given it's unbound). If audio was runtime suspended, this kind of works (but relies on some good luck). Upon HDA controller resume, we note acomp ops are NULL and HDMI/DP operations (like snd_hdac_display_power()) silently become no-ops. PCM streaming will go to /dev/null, but this is ok'ish since no monitor can be connected anyways. If audio was active, we start to get warnings or worse. Audio expects hw display codec to be powered and programmed, but suddenly it mey lose state. If the audio controller is actually part of the display hardware (e.g. discrete GPUs), then controller registers can stop functioning (they should be still available, but given the main diplay driver is unbound, odds of suprising behaviour are high). So this is less than ideal. I've been looking at options: 1) prevent/block the unbind if audio device is busy The component framework does not allow individual components to return -EBUSY, so there's no way to let others know that unbind is not possible now. This would force anyone testing DRM driver unbind to first unbind the audio driver and stop any active audio use-cases if needed. 2) unbind the ALSA card I've experimented doing a device_unregister() from the above callback, but this has not really worked (onion peeling exercise of new probelms). The code is shared by multiple controllers, so getting a handle to an snd_card object is not straighforward (drvdata is differnet for SOF and snd-hda-intel for instance). But with some new work, maybe we could call snd_card_disconnect() to detach the card and inform user-space. 3) continue as-is and try to fix bugs If audio is active, maybe we could force a acomp->put_power() to ensure a clean unregister of the display part. But this leaves a big chunk of issues especially with HDA controllers that require the display to be powered on, to function. .. Any ideas, and/or has there been prior work? It seems Takashi it's been mostly you who has been active working on the acomp integration recently. I also included Chris, Daniel and Jani who've had patches to hdac_component.c. Br, Kai

3 5

[PATCH] dt-bindings: sound:atmel-at91sam9g20ek: convert bindings to json-schema
by Balakrishnan Sambath 10 Dec '24

10 Dec '24

Convert atmel-at91sam9g20ek-wm8731-audio DT binding to yaml based json-schema.Change file name to match json-scheme naming. Signed-off-by: Balakrishnan Sambath <balakrishnan.s(a)microchip.com> --- .../bindings/sound/atmel,at91sam9g20ek-wm8731.yaml | 60 ++++++++++++++++++++++ .../sound/atmel-at91sam9g20ek-wm8731-audio.txt | 26 ---------- 2 files changed, 60 insertions(+), 26 deletions(-) diff --git a/Documentation/devicetree/bindings/sound/atmel,at91sam9g20ek-wm8731.yaml b/Documentation/devicetree/bindings/sound/atmel,at91sam9g20ek-wm8731.yaml new file mode 100644 index 000000000000..f6330707fe1b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/atmel,at91sam9g20ek-wm8731.yaml @@ -0,0 +1,60 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/atmel,at91sam9g20ek-wm8731.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Atmel at91sam9g20ek wm8731 audio complex + +maintainers: + - Balakrishnan Sambath <balakrishnan.s(a)microchip.com> + +properties: + compatible: + const: atmel,at91sam9g20ek-wm8731-audio + + atmel,model: + $ref: /schemas/types.yaml#/definitions/string + description: The user-visible name of this sound complex. + atmel,audio-routing: + $ref: /schemas/types.yaml#/definitions/non-unique-string-array + description: A list of the connections between audio components. + minItems: 2 + items: + enum: + # Board Connectors + - "Ext Spk" + - "Int MIC" + + # CODEC Pins + - LHPOUT + - MICIN + atmel,ssc-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: The phandle of the SSC controller + atmel,audio-codec: + $ref: /schemas/types.yaml#/definitions/phandle + description: The phandle of WM8731 audio codec + +required: + - compatible + - atmel,model + - atmel,audio-routing + - atmel,ssc-controller + - atmel,audio-codec + +additionalProperties: false + +examples: + - | + sound { + compatible = "atmel,at91sam9g20ek-wm8731-audio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pck0_as_mck>; + atmel,model = "wm8731 @ AT91SAMG20EK"; + atmel,audio-routing = + "Ext Spk", "LHPOUT", + "Int MIC", "MICIN"; + atmel,ssc-controller = <&ssc0>; + atmel,audio-codec = <&wm8731>; + }; diff --git a/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt b/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt deleted file mode 100644 index 9c5a9947b64d..000000000000 --- a/Documentation/devicetree/bindings/sound/atmel-at91sam9g20ek-wm8731-audio.txt +++ /dev/null @@ -1,26 +0,0 @@ -* Atmel at91sam9g20ek wm8731 audio complex - -Required properties: - - compatible: "atmel,at91sam9g20ek-wm8731-audio" - - atmel,model: The user-visible name of this sound complex. - - atmel,audio-routing: A list of the connections between audio components. - - atmel,ssc-controller: The phandle of the SSC controller - - atmel,audio-codec: The phandle of the WM8731 audio codec -Optional properties: - - pinctrl-names, pinctrl-0: Please refer to pinctrl-bindings.txt - -Example: -sound { - compatible = "atmel,at91sam9g20ek-wm8731-audio"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pck0_as_mck>; - - atmel,model = "wm8731 @ AT91SAMG20EK"; - - atmel,audio-routing = - "Ext Spk", "LHPOUT", - "Int MIC", "MICIN"; - - atmel,ssc-controller = <&ssc0>; - atmel,audio-codec = <&wm8731>; -}; --- base-commit: 0dd3ee31125508cd67f7e7172247f05b7fd1753a change-id: 20240214-at91sam9g20ek-wm8731-yaml-404ddddbb91a Best regards, -- Balakrishnan Sambath <balakrishnan.s(a)microchip.com>

5 5

[PATCH treewide 00/11] ASoC: Clean up {hp,mic}-det-gpio handling
by Geert Uytterhoeven 09 Dec '24

09 Dec '24

Hi all, The "gpio" suffix for GPIO consumers was deprecated a while ago, in favor of the "gpios" suffix. However, there are still several users of the "hp-det-gpio" and "mic-det-gpio" properties, in DT bindings, drivers, and DT source files. Drivers that use gpiolib handle both the deprecated and new properties transparently, but that is not the case when using of_property_*() calls directly. - The first patch fixes a bug, as the Freescale Generic ASoC Sound driver handles only the deprecated properties, while there is already a user of the new variants, - The second patch updates the Audio Graph and Simple Audio Card DT bindings, - Patches 3-9 converts various DTS files to use the new properties, - The last 2 patches convert Freescale sound device nodes to use the new properties. All patches can be applied independently, except for the last two, which depend on the first patch to avoid regressions. This series was compile-tested only. Thanks for your comments! Geert Uytterhoeven (11): ASoC: fsl-asoc-card: Add missing handling of {hp,mic}-dt-gpios ASoC: dt-bindings: Deprecate {hp,mic}-det-gpio ARM: dts: marvell: mmp2-olpc-xo-1-75: Switch to {hp,mic}-det-gpios arm64: dts: freescale: imx: Switch to simple-audio-card,hp-det-gpios arm64: dts: renesas: beacon-renesom: Switch to mic-det-gpios arm64: dts: rockchip: Switch to simple-audio-card,hp-det-gpios arm64: dts: rockchip: Switch to hp-det-gpios arm64: dts: uniphier: Switch to hp-det-gpios mips: dts: ingenic: Switch to simple-audio-card,hp-det-gpios ARM: dts: nxp: imx: Switch to {hp,mic}-det-gpios arm64: dts: freescale: imx: Switch to hp-det-gpios .../devicetree/bindings/sound/audio-graph.yaml | 6 ++++++ .../devicetree/bindings/sound/simple-card.yaml | 12 ++++++++++++ arch/arm/boot/dts/marvell/mmp2-olpc-xo-1-75.dts | 4 ++-- arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi | 4 ++-- arch/arm/boot/dts/nxp/imx/imx6sl-evk.dts | 2 +- arch/arm/boot/dts/nxp/imx/imx6sll-evk.dts | 2 +- arch/arm/boot/dts/nxp/imx/imx6sx-sdb.dtsi | 2 +- arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi | 2 +- arch/arm/boot/dts/nxp/imx/imx7d-sdb.dts | 2 +- .../boot/dts/freescale/imx8mq-librem5-devkit.dts | 2 +- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 2 +- arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 2 +- arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 2 +- arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts | 2 +- .../boot/dts/renesas/beacon-renesom-baseboard.dtsi | 2 +- .../boot/dts/rockchip/rk3326-anbernic-rg351m.dtsi | 2 +- .../arm64/boot/dts/rockchip/rk3326-gameforce-chi.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3326-odroid-go.dtsi | 2 +- arch/arm64/boot/dts/rockchip/rk3368-lba3368.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3399-roc-pc-plus.dts | 2 +- .../boot/dts/rockchip/rk3399-rock-pi-4a-plus.dts | 2 +- .../boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts | 2 +- .../boot/dts/rockchip/rk3399-sapphire-excavator.dts | 2 +- .../boot/dts/rockchip/rk3566-anbernic-rg-arc.dtsi | 2 +- .../boot/dts/rockchip/rk3566-anbernic-rg353p.dts | 2 +- .../boot/dts/rockchip/rk3566-anbernic-rg353ps.dts | 2 +- .../boot/dts/rockchip/rk3566-anbernic-rg353v.dts | 2 +- .../boot/dts/rockchip/rk3566-anbernic-rg353vs.dts | 2 +- .../boot/dts/rockchip/rk3566-anbernic-rg503.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3566-pinetab2.dtsi | 2 +- arch/arm64/boot/dts/rockchip/rk3566-powkiddy-x55.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3568-odroid-m1.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3588-armsom-sige7.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3588-evb1-v10.dts | 2 +- .../dts/rockchip/rk3588-friendlyelec-cm3588-nas.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3588-nanopc-t6.dtsi | 2 +- arch/arm64/boot/dts/rockchip/rk3588-ok3588-c.dts | 2 +- .../boot/dts/rockchip/rk3588-orangepi-5-plus.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3588-quartzpro64.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3588-rock-5-itx.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dts | 2 +- .../boot/dts/rockchip/rk3588s-gameforce-ace.dts | 2 +- .../boot/dts/socionext/uniphier-ld11-global.dts | 2 +- .../boot/dts/socionext/uniphier-ld20-global.dts | 2 +- arch/mips/boot/dts/ingenic/gcw0.dts | 2 +- arch/mips/boot/dts/ingenic/rs90.dts | 2 +- sound/soc/fsl/fsl-asoc-card.c | 8 +++++--- 50 files changed, 72 insertions(+), 52 deletions(-) -- 2.34.1 Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert(a)linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds

8 30

[PATCH v2 0/3] ASoC: mediatek:mt8186: fix both the speaker and hdmi
by Jiaxin Yu 06 Dec '24

06 Dec '24

The speaker and hdmi of mt8186 platform are shared the same port of I2S, when connect the external display, use build-in speakers to play audio, they both playback at the same time. So we want to manage the playback device through DAPM events. Change since v1: Support audio function for it6505 bridge to hdmi-codec Jiaxin Yu (3): ASoC: hdmi-codec: Add event handler for hdmi TX ASoC: mediatek: mt8186: correct the HDMI widgets drm/bridge: it6505: Add audio support drivers/gpu/drm/bridge/ite-it6505.c | 81 +++++++++++++++++-- include/sound/hdmi-codec.h | 6 ++ sound/soc/codecs/hdmi-codec.c | 37 ++++++++- .../mt8186/mt8186-mt6366-da7219-max98357.c | 2 +- .../mt8186/mt8186-mt6366-rt1019-rt5682s.c | 2 +- 5 files changed, 116 insertions(+), 12 deletions(-) -- 2.18.0

3 16

[PATCH] ASoC: tas2781: Fix redundant logical jump
by Tang Bin 02 Dec '24

02 Dec '24

In these functions, some logical jump of "goto" and variable are redundant, thus remove them. Signed-off-by: Tang Bin <tangbin(a)cmss.chinamobile.com> --- sound/soc/codecs/tas2781-i2c.c | 68 +++++++++++++--------------------- 1 file changed, 25 insertions(+), 43 deletions(-) diff --git a/sound/soc/codecs/tas2781-i2c.c b/sound/soc/codecs/tas2781-i2c.c index 68887799e..27f2f84a4 100644 --- a/sound/soc/codecs/tas2781-i2c.c +++ b/sound/soc/codecs/tas2781-i2c.c @@ -489,14 +489,11 @@ static int tas2563_calib_start_put(struct snd_kcontrol *kcontrol, struct snd_soc_component *comp = snd_soc_kcontrol_component(kcontrol); struct tasdevice_priv *tas_priv = snd_soc_component_get_drvdata(comp); const int sum = ARRAY_SIZE(tas2563_cali_start_reg); - int rc = 1; int i, j; guard(mutex)(&tas_priv->codec_lock); - if (tas_priv->chip_id != TAS2563) { - rc = -1; - goto out; - } + if (tas_priv->chip_id != TAS2563) + return -1; for (i = 0; i < tas_priv->ndev; i++) { struct tasdevice *tasdev = tas_priv->tasdevice; @@ -523,8 +520,8 @@ static int tas2563_calib_start_put(struct snd_kcontrol *kcontrol, q[j].val, 4); } } -out: - return rc; + + return 1; } static void tas2563_calib_stop_put(struct tasdevice_priv *tas_priv) @@ -576,7 +573,7 @@ static int tasdev_cali_data_put(struct snd_kcontrol *kcontrol, struct cali_reg *p = &cali_data->cali_reg_array; unsigned char *src = ucontrol->value.bytes.data; unsigned char *dst = cali_data->data; - int rc = 1, i = 0; + int i = 0; int j; guard(mutex)(&priv->codec_lock); @@ -605,7 +602,7 @@ static int tasdev_cali_data_put(struct snd_kcontrol *kcontrol, i += 3; memcpy(dst, &src[i], cali_data->total_sz); - return rc; + return 1; } static int tas2781_latch_reg_get(struct snd_kcontrol *kcontrol, @@ -1115,25 +1112,21 @@ static int tasdevice_dsp_create_ctrls(struct tasdevice_priv *tas_priv) char *conf_name, *prog_name; int nr_controls = 4; int mix_index = 0; - int ret; /* Alloc kcontrol via devm_kzalloc, which don't manually * free the kcontrol */ dsp_ctrls = devm_kcalloc(tas_priv->dev, nr_controls, sizeof(dsp_ctrls[0]), GFP_KERNEL); - if (!dsp_ctrls) { - ret = -ENOMEM; - goto out; - } + if (!dsp_ctrls) + return -ENOMEM; /* Create mixer items for selecting the active Program and Config */ prog_name = devm_kstrdup(tas_priv->dev, "Speaker Program Id", GFP_KERNEL); - if (!prog_name) { - ret = -ENOMEM; - goto out; - } + if (!prog_name) + return -ENOMEM; + dsp_ctrls[mix_index].name = prog_name; dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; dsp_ctrls[mix_index].info = tasdevice_info_programs; @@ -1143,10 +1136,9 @@ static int tasdevice_dsp_create_ctrls(struct tasdevice_priv *tas_priv) conf_name = devm_kstrdup(tas_priv->dev, "Speaker Config Id", GFP_KERNEL); - if (!conf_name) { - ret = -ENOMEM; - goto out; - } + if (!conf_name) + return -ENOMEM; + dsp_ctrls[mix_index].name = conf_name; dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; dsp_ctrls[mix_index].info = tasdevice_info_configurations; @@ -1156,10 +1148,9 @@ static int tasdevice_dsp_create_ctrls(struct tasdevice_priv *tas_priv) active_dev_num = devm_kstrdup(tas_priv->dev, "Activate Tasdevice Num", GFP_KERNEL); - if (!active_dev_num) { - ret = -ENOMEM; - goto out; - } + if (!active_dev_num) + return -ENOMEM; + dsp_ctrls[mix_index].name = active_dev_num; dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; dsp_ctrls[mix_index].info = tasdevice_info_active_num; @@ -1168,21 +1159,17 @@ static int tasdevice_dsp_create_ctrls(struct tasdevice_priv *tas_priv) mix_index++; chip_id = devm_kstrdup(tas_priv->dev, "Tasdevice Chip Id", GFP_KERNEL); - if (!chip_id) { - ret = -ENOMEM; - goto out; - } + if (!chip_id) + return -ENOMEM; + dsp_ctrls[mix_index].name = chip_id; dsp_ctrls[mix_index].iface = SNDRV_CTL_ELEM_IFACE_MIXER; dsp_ctrls[mix_index].info = tasdevice_info_chip_id; dsp_ctrls[mix_index].get = tasdevice_get_chip_id; mix_index++; - ret = snd_soc_add_component_controls(tas_priv->codec, dsp_ctrls, + return snd_soc_add_component_controls(tas_priv->codec, dsp_ctrls, nr_controls < mix_index ? nr_controls : mix_index); - -out: - return ret; } static int tasdevice_create_cali_ctrls(struct tasdevice_priv *priv) @@ -1469,7 +1456,6 @@ static int tasdevice_hw_params(struct snd_pcm_substream *substream, unsigned int slot_width; unsigned int fsrate; int bclk_rate; - int rc = 0; fsrate = params_rate(params); switch (fsrate) { @@ -1479,8 +1465,7 @@ static int tasdevice_hw_params(struct snd_pcm_substream *substream, default: dev_err(tas_priv->dev, "%s: incorrect sample rate = %u\n", __func__, fsrate); - rc = -EINVAL; - goto out; + return -EINVAL; } slot_width = params_width(params); @@ -1493,20 +1478,17 @@ static int tasdevice_hw_params(struct snd_pcm_substream *substream, default: dev_err(tas_priv->dev, "%s: incorrect slot width = %u\n", __func__, slot_width); - rc = -EINVAL; - goto out; + return -EINVAL; } bclk_rate = snd_soc_params_to_bclk(params); if (bclk_rate < 0) { dev_err(tas_priv->dev, "%s: incorrect bclk rate = %d\n", __func__, bclk_rate); - rc = bclk_rate; - goto out; + return bclk_rate; } -out: - return rc; + return 0; } static int tasdevice_set_dai_sysclk(struct snd_soc_dai *codec_dai, -- 2.33.0

3 2

[RFC PATCH 0/2] Add support for stacked and parallel memories
by Amit Kumar Mahapatra 25 Nov '24

25 Nov '24

Hello Everyone, Following an email discussion with Miquel regarding the binding changes and overall architecture for implementing support for stacked and parallel memories, I’m sharing this RFC to initiate a discussion on the proposed updates to current bindings and to finalize the implementation architecture. Before diving into the main topic, here is some background on stacked and parallel memories. The AMD QSPI controller supports two advanced connection modes(Stacked and Parallel) which allow the controller to treat two different flashes as one storage. Stacked: Flashes share the same SPI bus, but different CS line, controller driver asserts the CS of the flash to which it needs to communicate. Stacked mode is a software abstraction rather than a controller feature or capability. At any given time, the controller communicates with one of the two connected flash devices, as determined by the requested address and data length. If an operation starts on one flash and ends on the other, the core needs to split it into two separate operations and adjust the data length accordingly. Parallel(Multi-CS): Both the flashes have their separate SPI bus, CS of both the flashes will be asserted/de-asserted at the same time. In this mode data will be split across both the flashes by enabling the STRIPE setting in the controller. Parallel mode is a controller feature where if the STRIPE bit is set then the controller internally handles the data split during data write to the flashes and while reading data from the flash the controller internally merges data from both the flashes before writing to the controller FIFO. If STRIPE is not enabled, then same data will be sent to both the devices. In parallel mode both the flashes should be identical. For more information on the modes please feel free to go through the controller flash interface below [1]. Mirochip QSPI controller[2] also supports "Dual Parallel 8-bit IO mode", but they call it "Twin Quad Mode". Initially in [3] [4] [5] Miquel had tried to extend MTD-CONCAT driver to support Stacked mode, but the bindings were not accepted. So, the MTD-CONCAT approach was dropped and the DT bindings that got accepted [6] [7] [8] that describes the two flash devices as being one. SPI core changes to support the above bindings were added [9]. While adding the support in SPI-NOR Tudor provided additional feedback, leading to a discussion on updating the current stacked and parallel DT bindings. Proposed Solution: The solution has two parts: 1. Update MTD-CONCAT Update MTD-CONCAT to create virtual concatinated mtd devices as defined in the device tree. 2. Add a New Layer Add a new layer between the SPI-NOR and MTD layers to support stacked and parallel configurations. This new layer will be part of spi-nor, located in mtd/spi-nor/, can be included/excluded via Kconfig, will be maintained by AMD and will: - During probing, store information from all connected flashes in stacked or parallel mode and present them as a single device to the MTD layer. - Register callbacks and manage MTD device registration within the new layer instead of spi-nor/core.c. - Make minimal changes in spi-nor/core.c, as stacked and parallel handling will be managed by the new layer on top of SPI-NOR. - Handle odd byte count requests from the MTD layer during flash operations in parallel mode. [1] https://docs.amd.com/r/en-US/am011-versal-acap-trm/QSPI-Flash-Device-Interf… [2] https://ww1.microchip.com/downloads/aemDocuments/documents/MPU32/ProductDoc… [3] https://lore.kernel.org/all/20191113171505.26128-4-miquel.raynal@bootlin.co… [4] https://lore.kernel.org/all/20191127105522.31445-5-miquel.raynal@bootlin.co… [5]https://lore.kernel.org/all/20211112152411.818321-1-miquel.raynal@bootlin… [6] https://github.com/torvalds/linux/commit/f89504300e94524d5d5846ff8b728592ac… [7] https://github.com/torvalds/linux/commit/eba5368503b4291db7819512600fa014ea… [8] https://github.com/torvalds/linux/commit/e2edd1b64f1c79e8abda365149ed62a2a9… [9]https://github.com/torvalds/linux/commit/4d8ff6b0991d5e86b17b235fc46ec62e… Thanks, Amit Amit Kumar Mahapatra (2): dt-bindings: mtd: Add bindings for describing concatinated MTD devices dt-bindings: spi: Update stacked and parallel bindings .../mtd/partitions/fixed-partitions.yaml | 18 +++++++++++++++ .../bindings/mtd/partitions/partitions.yaml | 6 +++++ .../bindings/spi/spi-controller.yaml | 23 +++++++++++++++++-- .../bindings/spi/spi-peripheral-props.yaml | 9 +++----- 4 files changed, 48 insertions(+), 8 deletions(-) -- 2.34.1

6 15

[alsa-devel] Error patching file pcm_native.c
by Delusion's Master 20 Nov '24

20 Nov '24

Hi, first of all I apologize in case you receive multiple copies of this message, but I forgot to specify a subject in the original mail. I have a problem compiling the latest alsa driver snapshots. Specifically, it's a problem when patching pcm_native.c: [..] copying file alsa-kernel/core/info.c patching file info.c copying file alsa-kernel/core/pcm.c patching file pcm.c Hunk #3 succeeded at 739 (offset 2 lines). Hunk #5 succeeded at 954 (offset 2 lines). Hunk #7 succeeded at 1045 (offset 2 lines). copying file alsa-kernel/core/pcm_native.c patching file pcm_native.c Hunk #4 succeeded at 1544 (offset -25 lines). Hunk #5 succeeded at 2827 (offset 12 lines). Hunk #6 succeeded at 2878 (offset 10 lines). Hunk #7 FAILED at 2906. Hunk #8 FAILED at 2922. Hunk #9 succeeded at 2915 (offset -23 lines). Hunk #10 succeeded at 3036 (offset 10 lines). Hunk #11 succeeded at 3027 (offset -23 lines). Hunk #12 succeeded at 3074 (offset 10 lines). Hunk #13 succeeded at 3098 (offset -23 lines). Hunk #14 succeeded at 3143 (offset 10 lines). Hunk #15 succeeded at 3124 (offset -23 lines). Hunk #16 succeeded at 3214 (offset 10 lines). Hunk #17 succeeded at 3208 (offset -23 lines). Hunk #18 succeeded at 3271 (offset 10 lines). Hunk #19 succeeded at 3304 (offset -23 lines). Hunk #20 succeeded at 3386 (offset 10 lines). Hunk #21 succeeded at 3411 (offset -23 lines). Hunk #22 succeeded at 3456 (offset 10 lines). Hunk #23 succeeded at 3450 (offset -23 lines). Hunk #24 succeeded at 3525 (offset 10 lines). Hunk #25 succeeded at 3644 (offset -23 lines). 2 out of 25 hunks FAILED -- saving rejects to file pcm_native.c.rej make[2]: *** [pcm_native.c] Error 1 It's some days I get this, but I waited to report this since I thought it could be a temporary problem. My OS is Fedora 11 x86_64. Previous snapshots didn't give me this problem, but I can't say which one broke the compilation, since I usually try updated snapshots only at kernel updates. I searched for this error and the only relevant report I could find is this one: http://mailman.alsa-project.org/pipermail/alsa-devel/2009-April/016420.html a report from last April. What could the problem be? Thanks _________________________________________________________________ Invite your mail contacts to join your friends list with Windows Live Spaces. It's easy! http://spaces.live.com/spacesapi.aspx?wx_action=create&wx_url=/friends.aspx…

3 10

ASoC Kernel 6.1: Query regarding dynamic dai link/dapm registration during bootup
by Shalini Manjunatha (Consultant) (QUIC) 08 Nov '24

08 Nov '24

Hi All, On kernel6.1 based Qualcomm target for automotive platform based on Android U, we have a feature early services to launch certain early apps at early init of android bootup cycle. Hence in order to launch early chime sound of audio at early init of android boot up cycle, we need to load all required audio kernel modules at early init stage in order to get sound card registered. We have certain KPI goals for every early apps to get completed within lesser duration so that we can achieve final KPI goal of android boot complete as per the target specification. In this journey, while optimizing the sound card registration through machine driver probe to achieve lower KPI for audio early chime sound, we find that for early chime launch we required only selected pcm front end dai links only. Hence if we keep FE dai link structure in our machine driver with only required items for early chime, overall sound card registrations gets completed within 200msec from the time it starts, which is a very good KPI number to achieve. So we were trying out code change to split overall FE dai link structure into two, one for early chime and another for all other required dai link's, then some how we need to register early chime related dai link during early init so that sound card registration process gets completed quickly, later stage we want to dynamically load all other FE dai links. Could you please help us to suggest on how can we achieve this?. Is there any possible way out to avoid static FE dai link registration for all required ones from machine driver during machine driver probe, instead register only limited list of dai links. Later can we dynamically register the dai links in order to get PCM devices entries created based on use case. Currently we have this API devm_snd_soc_register_card() being called with snd_soc_card parameter which has all possible FE dai links populated at once. Queries: 1) can we register sound card twice during bootup, once with limited dai links and next with all required ones? 2) can we register dai links/dapm dynamically based on use case requriement? 3) If it is possible, could you share any reference from any other vendor who is able to achieve the same?. Regards, Shalini M

3 3