January 2024 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] [RFC PATCH 00/10] Add support for DMA and audio codec of F1C100s
by Mesih Kilinc 23 Oct '24

23 Oct '24

This is RFC patchset for Allwinner suniv F1C100s to support DMA and audio codec. Allwinner F1C100s has a audio codec that has necessary digital and analog parts. It has r-l headphone output and microphone, line, r-l FM inputs. ADC can capture any inputs and also output channels via mux. Any input channels or DAC samples can feed output channels. Add support for this audio codec. F1C100s utilizes DMA channels to send and receive ADC-DAC samples. So DMA support needed. Patch 1~5 adds support for DMA. Suniv F1C100s has very similar DMA to sun4i. But there is some dissimilarities also. Suniv features a DMA reset bit in clock control unit. It has smaller number of DMA channels. Several registers has different addresses. It's max burst size is 4 instead of 8. Also DMA endpoint numbers are different. Patch 6 adds DMA max burst option to sun4i-codec. Patch 7~8 Add support for suniv F1C100s audio codec. Patch 9 adds audio codec to suniv-f1c100s.dtsi Patch 10 adds audio codec support to Lichee Pi Nano board. Thanks! Mesih Kilinc (10): dma-engine: sun4i: Add a quirk to support different chips dma-engine: sun4i: Add has_reset option to quirk dt-bindings: dmaengine: Add Allwinner suniv F1C100s DMA dma-engine: sun4i: Add support for Allwinner suniv F1C100s ARM: dts: suniv: f1c100s: Add support for DMA ASoC: sun4i-codec: Add DMA Max Burst field dt-bindigs: sound: Add Allwinner suniv F1C100s Audio Codec ASoC: sun4i-codec: Add support for Allwinner suniv F1C100s ARM: dts: suniv: f1c100s: Add support for Audio Codec ARM: dts: suniv: f1c100s: Activate Audio Codec for Lichee Pi Nano .../devicetree/bindings/dma/sun4i-dma.txt | 4 +- .../devicetree/bindings/sound/sun4i-codec.txt | 5 + arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts | 8 + arch/arm/boot/dts/suniv-f1c100s.dtsi | 25 ++ drivers/dma/Kconfig | 4 +- drivers/dma/sun4i-dma.c | 221 ++++++++++-- sound/soc/sunxi/sun4i-codec.c | 371 ++++++++++++++++++++- 7 files changed, 601 insertions(+), 37 deletions(-) -- 2.7.4

5 18

[RFC PATCH 00/16] soundwire/ASoC: speed-up downloads with BTP/BRA protocol
by Pierre-Louis Bossart 20 Aug '24

20 Aug '24

This RFC patchset suggests a new API for ASoC codec drivers to use for firmware/table downloads. Problem statement: All existing transfers initiated by codec drivers rely on SoundWire read/write commands, which can only support ONE byte per frame. With the typical 48kHz frame rate, this means 384 kbits/s. In addition, the command/control is typically handled with a FIFO and interrupts which adds more software overhead. To give a practical reference, sending 32Kb takes 2.5s on Intel platforms, which means about 105kbit/s only. Additional non-audio activity is likely to adversely impact interrupt scheduling and further decrease the transfer speeds. New SDCA-based codecs have a need to download tables and DSP firmware which are typically between 20 and 256 Kb. The slow bus operation has a direct impact on boot/resume times, and clearly having to wait more than 300ms is a showstopper in terms of latency requirements and user-experience. Suggested solution: The MIPI specification and most of the new codecs support the Bulk Transfer Protocol (BTP) and specifically the Bulk Register Access (BRA) configuration. This mode reclaims the 'audio' data space of the SoundWire frame to send firmware/coefficients over the DataPort 0 (DP0). The API suggested is rather simple, with the following sequence expected: open(): reserve resources and prepare hardware send_async(): trigger DMAs and perform SoundWire bank switch wait(): wait for DMA completion and disable DMAs close(): release resources Benefits: Even after accounting for the protocol overhead, the data can be sent 8x or 16x faster on the link than with the regular commands. With the use of DMAs, the software overhead becomes limited to the initialization. Measured results show that transferring the same 32Kb takes about 100ms, a 25x improvement on the baseline write() commands with an actual bitrate of 2.6 Mbits/s. These results are a measure of bus/hardware performance mainly, and will typically not be too modified by the CPU activity and scheduling. The performance for reads is similar, with a 25x speedup measured. Limitations: Setting up the transfers over DP0 takes time, and the reliance on DMAs on the host side brings alignment restrictions. The BTP/BRA protocol is really only relevant for "large" transfers done during boot/resume *before* audio transfers take place. Mixing BTP/BRA and audio is a nightmare, this patchset suggests a mutual-exclusion between two usages. Scope: This patchset only exposes the API and a debugfs interface to initiate commands, validate results and measure performance. The actual use of the API is left as an exercise for codec driver developers. This patchset depends on a number of pre-requisite patches and will not build on top of any for-next branches. The main intent of this RFC is to gather comments on the usage, API, benefits and restrictions. The code and functionality was tested on an Intel LunarLake RVP platform connected to a Realtek RT711-SDCA device. Acknowledgements: Thanks to Zeek Tsai at Realtek for providing test sequences that helped reconcile the data formatted by the host driver with the expected results on the code side. Pierre-Louis Bossart (16): Documentation: driver: add SoundWire BRA description soundwire: cadence: add BTP support for DP0 soundwire: stream: extend sdw_alloc_stream() to take 'type' parameter soundwire: extend sdw_stream_type to BPT soundwire: stream: special-case the bus compute_params() routine soundwire: stream: reuse existing code for BPT stream soundwire: bus: add API for BPT protocol soundwire: bus: add bpt_stream pointer soundwire: crc8: add constant table soundwire: cadence: add BTP/BRA helpers to format data soundwire: intel_auxdevice: add indirection for BPT open/close/send_async/wait ASoC: SOF: Intel: hda-sdw-bpt: add helpers for SoundWire BPT DMA soundwire: intel: add BPT context definition soundwire: intel_ace2x: add BPT open/close/send_async/wait soundwire: debugfs: add interface for BPT/BRA transfers ASoC: rt711-sdca: add DP0 support Documentation/driver-api/soundwire/bra.rst | 478 +++++++++++++ Documentation/driver-api/soundwire/index.rst | 1 + Documentation/driver-api/soundwire/stream.rst | 2 +- .../driver-api/soundwire/summary.rst | 5 +- drivers/soundwire/Kconfig | 1 + drivers/soundwire/Makefile | 4 +- drivers/soundwire/amd_manager.c | 2 +- drivers/soundwire/bus.c | 77 +++ drivers/soundwire/bus.h | 18 + drivers/soundwire/cadence_master.c | 646 +++++++++++++++++- drivers/soundwire/cadence_master.h | 30 + drivers/soundwire/crc8.c | 277 ++++++++ drivers/soundwire/crc8.h | 11 + drivers/soundwire/debugfs.c | 122 +++- .../soundwire/generic_bandwidth_allocation.c | 84 ++- drivers/soundwire/intel.h | 12 + drivers/soundwire/intel_ace2x.c | 377 ++++++++++ drivers/soundwire/intel_auxdevice.c | 55 ++ drivers/soundwire/qcom.c | 2 +- drivers/soundwire/stream.c | 137 +++- include/linux/soundwire/sdw.h | 91 ++- include/linux/soundwire/sdw_intel.h | 16 + include/sound/hda-sdw-bpt.h | 76 +++ sound/soc/codecs/rt711-sdca-sdw.c | 8 + sound/soc/qcom/sdw.c | 2 +- sound/soc/sof/intel/Kconfig | 8 +- sound/soc/sof/intel/Makefile | 4 + sound/soc/sof/intel/hda-sdw-bpt.c | 328 +++++++++ 28 files changed, 2810 insertions(+), 64 deletions(-) create mode 100644 Documentation/driver-api/soundwire/bra.rst create mode 100644 drivers/soundwire/crc8.c create mode 100644 drivers/soundwire/crc8.h create mode 100644 include/sound/hda-sdw-bpt.h create mode 100644 sound/soc/sof/intel/hda-sdw-bpt.c -- 2.39.2

4 60

[PATCH v11 00/10] spi: Add support for stacked/parallel memories
by Amit Kumar Mahapatra 19 Aug '24

19 Aug '24

This patch series updated the spi-nor, spi core and the AMD-Xilinx GQSPI driver to add stacked and parallel memories support. The first nine patches https://lore.kernel.org/all/20230119185342.2093323-1-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-2-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-3-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-4-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-5-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-6-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-7-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-8-amit.kumar-mahapatra@a… https://lore.kernel.org/all/20230310173217.3429788-9-amit.kumar-mahapatra@a… of the previous series got applied to https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next But the rest of the patches in the series did not get applied as failure was reported for spi driver with GPIO CS, so send the remaining patches in the series after rebasing it on top of for-next branch and fixing the issue. CS GPIO is not tested on our hardware, but it has been tested by @Stefan https://lore.kernel.org/all/005001da1efc$619ad5a0$24d080e0$@opensource.cirr… --- BRANCH: for-next Changes in v11: - Rebased patch series on top of latest for-next branch. - Added a new patch(1/10) to replace spi->chip_select with spi_get_chipselect() call in tps6594-spi.c. - Added a new patch(2/10) to replace spi->chip_select with spi_get_chipseletc() call in cs35l56_hda_spi.c. - In spi.c initialized unused CS[] to 0xff and spi->cs_index_mask to 0x01 in all flows. - Updated spi_dev_check() to compare the CS of old spi device with the new spi device CS. - Updated cover letter description to add information regarding GPIO CS testing and added Stefen's Tested-by tag in 3/10 patch. Changes in v10: - Rebased patch series on top of latest for-next branch and fixed merge conflicts. Changes in v9: - Updated 1/8 patch description to add an high-level overview of parallel(multi-cs) & stacked design. - Initialized all unused CS to 0xFF. - Moved CS check from spi_add_device() to __spi_add_device(). - Updated __spi_add_device() to check to make sure that multiple logical CS don't map to the same physical CS and same physical CS doesn't map to different logical CS. - Updated 1/8, 5/8 & 7/8 to support arbitrary number of flash devices connected in parallel or stacked mode. - Updated documentation for chip_select. - Added a new spi-nor structure member nor->num_flash to keep track of the number of flashes connected. - Added a new patch in the series 4/8 to move write_enable call just before spi_mem ops call in SPI-NOR. - Added comments in SPI core & SPI-NOR. - Rebased the patch series on top of the latest for-next branch. Changes in v8: - Updated __spi_add_device() and spi_set_cs() to fix spi driver failure with GPIO CS. - Rebased the patch series on top of latest for-next branch and fixed merge conflicts. - Updated cover letter description to add information regarding GPIO CS testing and request Stefan to provide his Tested-by tag for 1/7 patch. - Updated 1/7 patch description. Changes in v7: - Updated spi_dev_check() to avoid failures for spi driver GPIO CS and moved the error message from __spi_add_device() to spi_dev_check(). - Resolved code indentation issue in spi_set_cs(). - In spi_set_cs() call spi_delay_exec( ) once if the controller supports multi cs with both the CS backed by GPIO. - Updated __spi_validate()to add checks for both the GPIO CS. - Replaced cs_index_mask bit mask with SPI_CS_CNT_MAX. - Updated struct spi_controller to represent multi CS capability of the spi controller through a flag bit SPI_CONTROLLER_MULTI_CS instead of a boolen structure member "multi_cs_cap". - Updated 1/7 patch description . Changes in v6: - Rebased on top of latest v6.3-rc1 and fixed merge conflicts in spi-mpc512x-psc.c, sfdp.c, spansion.c files and removed spi-omap-100k.c. - Updated spi_dev_check( ) to reject new devices if any one of the chipselect is used by another device. Changes in v5: - Rebased the patches on top of v6.3-rc1 and fixed the merge conflicts. - Fixed compilation warnings in spi-sh-msiof.c with shmobile_defconfig Changes in v4: - Fixed build error in spi-pl022.c file - reported by Mark. - Fixed build error in spi-sn-f-ospi.c file. - Added Reviewed-by: Serge Semin <fancer.lancer(a)gmail.com> tag. - Added two more patches to replace spi->chip_select with API calls in mpc832x_rdb.c & cs35l41_hda_spi.c files. Changes in v3: - Rebased the patches on top of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next - Added a patch to convert spi_nor_otp_region_len(nor) & spi_nor_otp_n_regions(nor) macros into inline functions - Added Reviewed-by & Acked-by tags Changes in v2: - Rebased the patches on top of v6.2-rc1 - Created separate patch to add get & set APIs for spi->chip_select & spi->cs_gpiod, and replaced all spi->chip_select and spi->cs_gpiod references with the API calls. - Created separate patch to add get & set APIs for nor->params. --- Amit Kumar Mahapatra (10): mfd: tps6594: Use set/get APIs to access spi->chip_select ALSA: hda/cs35l56: Use set/get APIs to access spi->chip_select spi: Add multi-cs memories support in SPI core mtd: spi-nor: Convert macros with inline functions mtd: spi-nor: Add APIs to set/get nor->params mtd: spi-nor: Move write enable inside specific write & erase APIs mtd: spi-nor: Add stacked memories support in spi-nor spi: spi-zynqmp-gqspi: Add stacked memories support in GQSPI driver mtd: spi-nor: Add parallel memories support in spi-nor spi: spi-zynqmp-gqspi: Add parallel memories support in GQSPI driver drivers/mfd/tps6594-spi.c | 2 +- drivers/mtd/spi-nor/atmel.c | 17 +- drivers/mtd/spi-nor/core.c | 683 +++++++++++++++++++++++++------ drivers/mtd/spi-nor/core.h | 8 + drivers/mtd/spi-nor/debugfs.c | 4 +- drivers/mtd/spi-nor/gigadevice.c | 4 +- drivers/mtd/spi-nor/issi.c | 11 +- drivers/mtd/spi-nor/macronix.c | 10 +- drivers/mtd/spi-nor/micron-st.c | 35 +- drivers/mtd/spi-nor/otp.c | 48 ++- drivers/mtd/spi-nor/sfdp.c | 33 +- drivers/mtd/spi-nor/spansion.c | 57 +-- drivers/mtd/spi-nor/sst.c | 7 +- drivers/mtd/spi-nor/swp.c | 25 +- drivers/mtd/spi-nor/winbond.c | 2 +- drivers/mtd/spi-nor/xilinx.c | 18 +- drivers/spi/spi-zynqmp-gqspi.c | 58 ++- drivers/spi/spi.c | 259 ++++++++++-- include/linux/mtd/spi-nor.h | 21 +- include/linux/spi/spi.h | 51 ++- sound/pci/hda/cs35l56_hda_spi.c | 2 +- 21 files changed, 1085 insertions(+), 270 deletions(-) -- 2.17.1

10 61

[alsa-devel] unsupported variant of snd_hda_intel
by Alexandre 04 Jul '24

04 Jul '24

Hello, I have an Acer Aspire 4736G laptop. The soundcard that is shipped in this laptop is intel-hda based as shown (actually it's a realtek): cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0x9b300000 irq 46 Basic sound output is correct but few feature are missing: - internal mic seems to be found but do not works. - sound output stop working when trying to send it using HDMI output - heads do not work when plugged neither when forcing pulseaudio to use it. I have an ubuntu 10.10 which is shipped with alsa 1.0.23. I have googled around and tried loading the snd-hda-intel with several parameters () as found in HD-Audio-Models.txt to no avail. cat /proc/asound/pcm 00-00: ALC888 Analog : ALC888 Analog : playback 1 : capture 1 00-01: ALC888 Digital : ALC888 Digital : playback 1 00-03: NVIDIA HDMI : NVIDIA HDMI : playback 1 Where can I begin to help implement the support for this sound card? I have very skills in developement in general but am ready to try if it is not to hard (I supose I can use previous code for similar models).. I just need a shepherd. Thanks

4 4

[PATCH v9 00/13] Introduce STM32 Firewall framework
by Gatien Chevallier 24 Apr '24

24 Apr '24

Introduce STM32 Firewall framework for STM32MP1x and STM32MP2x platforms. STM32MP1x(ETZPC) and STM32MP2x(RIFSC) Firewall controllers register to the framework to offer firewall services such as access granting. This series of patches is a new approach on the previous STM32 system bus, history is available here: https://lore.kernel.org/lkml/20230127164040.1047583/ The need for such framework arises from the fact that there are now multiple hardware firewalls implemented across multiple products. Drivers are shared between different products, using the same code. When it comes to firewalls, the purpose mostly stays the same: Protect hardware resources. But the implementation differs, and there are multiple types of firewalls: peripheral, memory, ... Some hardware firewall controllers such as the RIFSC implemented on STM32MP2x platforms may require to take ownership of a resource before being able to use it, hence the requirement for firewall services to take/release the ownership of such resources. On the other hand, hardware firewall configurations are becoming more and more complex. These mecanisms prevent platform crashes or other firewall-related incoveniences by denying access to some resources. The stm32 firewall framework offers an API that is defined in firewall controllers drivers to best fit the specificity of each firewall. For every peripherals protected by either the ETZPC or the RIFSC, the firewall framework checks the firewall controlelr registers to see if the peripheral's access is granted to the Linux kernel. If not, the peripheral is configured as secure, the node is marked populated, so that the driver is not probed for that device. The firewall framework relies on the access-controller device tree binding. It is used by peripherals to reference a domain access controller. In this case a firewall controller. The bus uses the ID referenced by the access-controller property to know where to look in the firewall to get the security configuration for the peripheral. This allows a device tree description rather than a hardcoded peripheral table in the bus driver. The STM32 ETZPC device is responsible for filtering accesses based on security level, or co-processor isolation for any resource connected to it. The RIFSC is responsible for filtering accesses based on Compartment ID / security level / privilege level for any resource connected to it. STM32MP13/15/25 SoC device tree files are updated in this series to implement this mecanism. Changes in V9: - Added Rob's reviews tags on bindings/of files - Added "simple-bus" to RIFSC/ETZPC compatible item list Changes in V8: - Add missing "simple-bus" compatible in STM32MP13/25 SoC device tree files for the ETZPC/RIFSC nodes - Add missing dependency on OF for OF_DYNAMIC that is selected by STM32_FIREWALL Changes in V7: - Separate indentation changes from access-controllers changes in the device tree file commits - Select OF_DYNAMIC when STM32_FIREWALL is set in order to use of_detach_node() in the firewall framework - Handle previously non-present RNG and HASH nodes in the STM32MP13 device tree file Changes in V6: - Rename access-controller to access-controllers - Remove access-controller-provider - Update device trees and other bindings accordingly - Rework ETZPC/RIFSC bindings to define what access-controllers cells contain inside #access-controller-cells - Some other minor fixes Changes in V5: - Integrate and rework the "feature-domains" binding patch in this patchset. The binding is renamed to "access-controller" - Rename every feature-domain* reference to access-control* ones - Correct loop bug and missing select STM32_FIREWALL in 32-bit platform Kconfig Changes in V4: - Fix typo in commit message and YAML check errors in "dt-bindings: Document common device controller bindings" Note: This patch should be ignored as stated in the cover letter. I've done this to avoid errors on this series of patch - Correct code syntax/style issues reported by Simon Horman - Added Jonathan's tag for IIO on the treewide patch Changes in V3: Change incorrect ordering for bindings commits leading to an error while running "make DT_CHECKER_FLAGS=-m dt_binding_check" Changes in V2: generic: - Add fw_devlink dependency for "feature-domains" property. bindings: - Corrected YAMLS errors highlighted by Rob's robot - Firewall controllers YAMLs no longer define the maxItems for the "feature-domains" property - Renamed st,stm32-rifsc.yaml to st,stm32mp25-rifsc.yaml - Fix examples in YAML files - Change feature-domains maxItems to 2 in firewall consumer files as there should not be more than 2 entries for now - Declare "feature-domain-names" as an optional property for firewall controllers child nodes. - Add missing "feature-domains" property declaration in bosch,m_can.yaml and st,stm32-cryp.yaml files firewall framework: - Support multiple entries for "feature-domains" property - Better handle the device-tree parsing using phandle+args APIs - Remove "resource firewall" type - Add a field for the name of the firewall entry - Fix licenses RIFSC: - Add controller name - Driver is now a module_platform_driver - Fix license ETZPC: - Add controller name - Driver is now a module_platform_driver - Fix license Device trees: - Fix rifsc node name - Move the "ranges" property under the "feature-domains" one Gatien Chevallier (12): dt-bindings: treewide: add access-controllers description dt-bindings: bus: document RIFSC dt-bindings: bus: document ETZPC firewall: introduce stm32_firewall framework of: property: fw_devlink: Add support for "access-controller" bus: rifsc: introduce RIFSC firewall controller driver arm64: dts: st: add RIFSC as an access controller for STM32MP25x boards bus: etzpc: introduce ETZPC firewall controller driver ARM: dts: stm32: add ETZPC as a system bus for STM32MP15x boards ARM: dts: stm32: put ETZPC as an access controller for STM32MP15x boards ARM: dts: stm32: add ETZPC as a system bus for STM32MP13x boards ARM: dts: stm32: put ETZPC as an access controller for STM32MP13x boards Oleksii Moisieiev (1): dt-bindings: document generic access controllers .../access-controllers.yaml | 84 + .../bindings/bus/st,stm32-etzpc.yaml | 96 + .../bindings/bus/st,stm32mp25-rifsc.yaml | 105 + .../bindings/crypto/st,stm32-cryp.yaml | 4 + .../bindings/crypto/st,stm32-hash.yaml | 4 + .../devicetree/bindings/dma/st,stm32-dma.yaml | 4 + .../bindings/dma/st,stm32-dmamux.yaml | 4 + .../devicetree/bindings/i2c/st,stm32-i2c.yaml | 4 + .../bindings/iio/adc/st,stm32-adc.yaml | 4 + .../bindings/iio/adc/st,stm32-dfsdm-adc.yaml | 4 + .../bindings/iio/dac/st,stm32-dac.yaml | 4 + .../bindings/media/cec/st,stm32-cec.yaml | 4 + .../bindings/media/st,stm32-dcmi.yaml | 4 + .../memory-controllers/st,stm32-fmc2-ebi.yaml | 4 + .../bindings/mfd/st,stm32-lptimer.yaml | 4 + .../bindings/mfd/st,stm32-timers.yaml | 4 + .../devicetree/bindings/mmc/arm,pl18x.yaml | 4 + .../bindings/net/can/bosch,m_can.yaml | 4 + .../devicetree/bindings/net/stm32-dwmac.yaml | 4 + .../bindings/phy/phy-stm32-usbphyc.yaml | 4 + .../bindings/regulator/st,stm32-vrefbuf.yaml | 4 + .../devicetree/bindings/rng/st,stm32-rng.yaml | 4 + .../bindings/serial/st,stm32-uart.yaml | 4 + .../bindings/sound/st,stm32-i2s.yaml | 4 + .../bindings/sound/st,stm32-sai.yaml | 4 + .../bindings/sound/st,stm32-spdifrx.yaml | 4 + .../bindings/spi/st,stm32-qspi.yaml | 4 + .../devicetree/bindings/spi/st,stm32-spi.yaml | 4 + .../devicetree/bindings/usb/dwc2.yaml | 4 + MAINTAINERS | 7 + arch/arm/boot/dts/st/stm32mp131.dtsi | 1063 ++++--- arch/arm/boot/dts/st/stm32mp133.dtsi | 51 +- arch/arm/boot/dts/st/stm32mp13xc.dtsi | 19 +- arch/arm/boot/dts/st/stm32mp13xf.dtsi | 19 +- arch/arm/boot/dts/st/stm32mp151.dtsi | 2756 +++++++++-------- arch/arm/boot/dts/st/stm32mp153.dtsi | 52 +- arch/arm/boot/dts/st/stm32mp15xc.dtsi | 19 +- arch/arm/mach-stm32/Kconfig | 1 + arch/arm64/Kconfig.platforms | 1 + arch/arm64/boot/dts/st/stm32mp251.dtsi | 7 +- drivers/bus/Kconfig | 10 + drivers/bus/Makefile | 1 + drivers/bus/stm32_etzpc.c | 141 + drivers/bus/stm32_firewall.c | 294 ++ drivers/bus/stm32_firewall.h | 83 + drivers/bus/stm32_rifsc.c | 252 ++ drivers/of/property.c | 2 + include/linux/bus/stm32_firewall_device.h | 141 + 48 files changed, 3370 insertions(+), 1938 deletions(-) create mode 100644 Documentation/devicetree/bindings/access-controllers/access-controllers.yaml create mode 100644 Documentation/devicetree/bindings/bus/st,stm32-etzpc.yaml create mode 100644 Documentation/devicetree/bindings/bus/st,stm32mp25-rifsc.yaml create mode 100644 drivers/bus/stm32_etzpc.c create mode 100644 drivers/bus/stm32_firewall.c create mode 100644 drivers/bus/stm32_firewall.h create mode 100644 drivers/bus/stm32_rifsc.c create mode 100644 include/linux/bus/stm32_firewall_device.h -- 2.35.3

5 19

[PATCH v4 0/7] Patches to update for rockchip pdm
by Sugar Zhang 23 Apr '24

23 Apr '24

These patches fixup or update for rockchip pdm. Changes in v4: - Acked by Rob Herring Changes in v3: - Fix property 'path-map' suggested by Rob Herring. Changes in v2: - Fix yamllint errors. Sugar Zhang (7): ASoC: rockchip: Add support for rv1126 pdm ASoC: dt-bindings: rockchip: Add binding for rv1126 pdm ASoC: rockchip: pdm: Add support for rk3568 pdm ASoC: dt-bindings: rockchip: Add binding for rk3568 pdm ASoC: rockchip: pdm: Add support for path map ASoC: dt-bindings: rockchip: pdm: Document property 'rockchip,path-map' ASoC: dt-bindings: rockchip: Convert pdm bindings to yaml .../devicetree/bindings/sound/rockchip,pdm.txt | 46 -------- .../devicetree/bindings/sound/rockchip,pdm.yaml | 120 +++++++++++++++++++++ sound/soc/rockchip/rockchip_pdm.c | 112 +++++++++++++++++-- sound/soc/rockchip/rockchip_pdm.h | 6 ++ 4 files changed, 232 insertions(+), 52 deletions(-) delete mode 100644 Documentation/devicetree/bindings/sound/rockchip,pdm.txt create mode 100644 Documentation/devicetree/bindings/sound/rockchip,pdm.yaml -- 2.7.4

3 9

[PATCH 0/7] Soundwire: clean up sysfs group creation
by Greg Kroah-Hartman 28 Mar '24

28 Mar '24

Note, this is a redone version of a very old series I wrote back in 2022: https://lore.kernel.org/r/20220824135951.3604059-1-gregkh@linuxfoundation.o… but everyone has forgotten about it now, and I've reworked it, so I'm considering it a "new" version, and not v2. Here's a series that adds the functionality to the driver core to hide entire attribute groups, in a much saner way than we have attempted in the past (i.e. dynamically figuring it out.) Many thanks to Dan for this patch. I'll also be taking this into my driver-core branch and creating a stable tag for anyone else to pull from to get it into their trees, as I think it will want to be in many for this development cycle. After the driver core change, there's cleanups to the soundwire core for how the attribute groups are created, to remove the "manual" creation of them, and allow the driver core to create them correctly, as needed, when needed, which makes things much smaller for the soundwire code to manage. Comments appreciated! thanks, greg k-h Dan Williams (1): sysfs: Introduce a mechanism to hide static attribute_groups Greg Kroah-Hartman (5): soundwire: sysfs: move sdw_slave_dev_attr_group into the existing list of groups soundwire: sysfs: cleanup the logic for creating the dp0 sysfs attributes soundwire: sysfs: have the driver core handle the creation of the device groups soundwire: sysfs: remove sdw_slave_sysfs_init() soundwire: sysfs: remove unneeded ATTRIBUTE_GROUPS() comments drivers/soundwire/bus_type.c | 5 ++- drivers/soundwire/sysfs_local.h | 4 +- drivers/soundwire/sysfs_slave.c | 64 ++++++++++++++--------------- drivers/soundwire/sysfs_slave_dpn.c | 3 ++ fs/sysfs/group.c | 45 ++++++++++++++++---- include/linux/sysfs.h | 63 ++++++++++++++++++++++------ 6 files changed, 126 insertions(+), 58 deletions(-) -- 2.43.0

5 22

[PATCH 0/7] ASoC: mediatek: AFE drivers cleanups
by AngeloGioacchino Del Regno 26 Mar '24

26 Mar '24

This series converts MediaTek AFE drivers' probe functions to use dev_err_probe() and devm functions where possible and, in some cases, dropping the .remove_new() callback, reducing the size. Cheers! AngeloGioacchino Del Regno (7): ASoC: mediatek: mt8173-afe-pcm: Convert to devm_pm_runtime_enable() ASoC: mediatek: mt8173-afe-pcm: Use devm_snd_soc_register_component() ASoC: mediatek: mt8183-afe-pcm: Convert to devm_pm_runtime_enable() ASoC: mediatek: mt8183-afe-pcm: Simplify with dev_err_probe() ASoC: mediatek: mt8192-afe-pcm: Convert to devm_pm_runtime_enable() ASoC: mediatek: mt8192-afe-pcm: Simplify with dev_err_probe() ASoC: mediatek: mt8195-afe-pcm: Drop .remove_new() callback sound/soc/mediatek/mt8173/mt8173-afe-pcm.c | 78 +++------------ sound/soc/mediatek/mt8183/mt8183-afe-pcm.c | 108 +++++++-------------- sound/soc/mediatek/mt8192/mt8192-afe-pcm.c | 95 ++++++------------ sound/soc/mediatek/mt8195/mt8195-afe-pcm.c | 12 +-- 4 files changed, 81 insertions(+), 212 deletions(-) -- 2.43.0

5 15

[PATCH 0/2] ALSA/ASoC/SOF: SSP dev_type support
by Peter Ujfalusi 26 Mar '24

26 Mar '24

Hi, SOF always passed 0 as dev_type to intel_nhlt_get_endpoint_blob() when looking up the blob from the NHLT table. This causes issues since alsa-utils commit 3a47ef2487ed ("topology: nhlt: intel: support more device types and directions") The dev_type is no longer always 0 in the topology embedded NHLT table resulting lookup failures for analog codecs since they will have dev_type=4. With SOF the dev_type is not used, we always use the SSP port index for looking up the configuration blob. The solution for the issue is to fetch the dev_type for the SSP port and feed it back to the intel_nhlt_get_endpoint_blob() to be able to find the configuration regardless of the assigned dev_type. Regards, Peter --- Brent Lu (2): ALSA: hda: intel-nhlt: add intel_nhlt_ssp_device_type() function ASoC: SOF: ipc4-topology: support NHLT device type include/sound/intel-nhlt.h | 10 ++++++++++ sound/hda/intel-nhlt.c | 26 ++++++++++++++++++++++++++ sound/soc/sof/ipc4-topology.c | 19 ++++++++++++++++--- 3 files changed, 52 insertions(+), 3 deletions(-) -- 2.43.0

3 6

[PATCH v9 00/27] Add support for QMC HDLC, framer infrastructure and PEF2256 framer
by Herve Codina 14 Mar '24

14 Mar '24

Hi, I have a system where I need to handle an HDLC interface and some audio data. The HDLC data are transferred using a TDM bus on which a PEF2256 (E1/T1 framer) is present. The PEF2256 transfers data from/to the TDM bus to/from the E1 line. This PEF2256 is connected to a PowerQUICC SoC for the control path and the TDM is connected to the SoC (QMC component) for the data path. From the QMC HDLC driver, I need to handle HDLC data using the QMC, carrier detection using the PEF2256 (E1 line carrier) and set/get some PEF2256 configuration. The QMC HDLC driver considers the PEF2256 as a generic framer. It performs operations that involve the PEF2256 through the generic framer API. The audio data are exchanged with the PEF2256 using a CPU DAI connected to the TDM bus through the QMC and the PEF2256 needs to be seen as a codec in order to be linked to the CPU DAI. The codec handles the carrier detection using the PEF2256 and reports the carrier state to the ALSA subsystem using the ASoC jack detection. The codec, even if instantiated by the PEF2256 driver, considers the PEF2256 as a generic framer. The generic framer has: - 2 consumers (QMC HDLC drv and codec) - 1 provider (PEF2256) So, the design is the following: +------------------+ +---------+ | QMC | <- TDM -> | PEF2256 | <-> E1 +---------+ | +-------------+ | | | | CPU DAI | <-data--> | QMC channel | | | | +---------+ | +-------------+ | | | +--------------+ | +-------------+ | | | | QMC HDLC drv | <-data--> | QMC channel | | | | +--------------+ | +-------------+ | | | ^ +------------------+ | | | +--------+ +-------------+ | | +-> | framer | <-> | PEF2256 drv | <- local bus ->| | | | | | +---------+ +-> | | | | | +--------+ | +-------+ | +-------------------> | codec | | | +-------+ | +-------------+ Further more, the TDM timeslots used by the QMC HDLC driver need to be configured at runtime (QMC dynamic timeslots). Several weeks ago, I sent two series related to this topic: - Add the Lantiq PEF2256 audio support [1] - RFC Add support for QMC HDLC and PHY [2] This current series is a rework of these two series taking into account feedbacks previously received. In order to implement all of this, I do the following: 1) Perform some fixes (patches 1, 2, 3, 4, 5 ) 2) Introduce the QMC HDLC driver (patches 6, 7, 8) 3) Add QMC dynamic timeslot support (patches 9 - 19) 4) Add timeslots change support in QMC HDLC (patch 20) 5) Introduce framer infrastructure (patch 21) 6) Add PEF2256 framer provider (patches 22, 23, 24, 25) 7) Add framer codec as a framer consumer (patch 26) 8) Add framer support as a framer consumer in QMC HDLC (patch 27) The series contains the full story and detailed modifications. If needed, the series can be split and/or commits can be squashed. Let me know. Compare to the previous iteration https://lore.kernel.org/linux-kernel/20231011061437.64213-1-herve.codina@bo… This v9 series: - Removes some patches already applied - Adds some 'Acked-by' tags Best regards, Hervé [1]: https://lore.kernel.org/all/20230417171601.74656-1-herve.codina@bootlin.com/ [2]: https://lore.kernel.org/all/20230323103154.264546-1-herve.codina@bootlin.co… Changes v8 -> v9 - Removed Patches 6, 7 and 8 (patches applied) - Patches 7, 20, 21, 23 (patches 10, 23, 24, 26 in v8) Add 'Acked-by: Jakub Kicinski <kuba(a)kernel.org>' Changes v7 -> v8 - Patch 10 Fix a race condition when stopping the queue in qmc_hdlc_close() - Patch 24 Move to menuconfig and hide CONFIG_GENERIC_FRAMER Remove unneeded check (defensive programming) Remove unneeded variable assignment - Patch 25 Add 'Reviewed-by: Rob Herring <robh(a)kernel.org>' - Patch 26 Use array notation for 'audio_devs' Changes v6 -> v7 - Patch 8 Move the 'compatible' property to the first property. Add device/SoC specific compatible strings. Add 'Reviewed-by: Rob Herring <robh(a)kernel.org>' - Patch 25 Remove '$ref' from the lantiq,data-rate-bps property. '-bps' is now a standard suffix. Changes v5 -> v6 - All patches Remove 'Signed-off-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' These Sob were added by Christophe when he sent the v4 while I was on vacation. https://lore.kernel.org/linux-kernel/992a2b31-e21f-eee3-8bfc-a65b69fe5bd7@c… - Patch 6, 7 Add 'Acked-by: Conor Dooley <conor.dooley(a)microchip.com>' Add 'Acked-by: Rob Herring <robh(a)kernel.org>' - Patch 8 Add a constraint on fsl,framer. - Patch 25 Fix clocks description (inconsistent capitalisation) Use '8-bit' instead of '8bit' Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Removed patch 26 (patch applied) - Patch 26 (patch 27 in v5) Add 'Reviewed-by: Linus Walleij <linus.walleij(a)linaro.org>' - Patch 27 (patch 28 in v5) Move registers definition to .c file and remove .h file Add 'select PINCONF' in Kconfig Use dev_err_probe() Add 'Reviewed-by: Linus Walleij <linus.walleij(a)linaro.org>' - Patch 28 (patch 29 in v5) Remove .h file Changes v4 -> v5 - Patches 1 to 5 No changes - Patch 6 (new in v5) Fix QMC binding example - Patch 7 (new in v5) Add missing 'additionalProperties: false' - Patch 8 (new in v5, replace v4 patch 6) Add QMC HDLC properties in the QMC channel node Renamed the 'framer' property to 'fsl,framer' - Patch 9 (new in v5) Add support for QMC child devices - Patch 10 (patch 7 in v4) No changes - Patch 11 (patch 8 in v4) Remove fsl,qmc-hdlc.yaml (no more existing file) - Patches 12 to 22 (patches 9 to 19 in v4) No changes - Patch 23 (patch 20 in v4) Remove unused variable initializations Remove extra space - Patch 24 (patch 21 in v4) Improve Kconfig help text Fix variable declaration (reverse xmas tree) Fix typos and extra spaces Fix documentation issues raised by 'kernel-doc -none' Move of_node_put() and kfree() out of the mutex Replace ida_simple_{get,remove}() by ida_{alloc,free}() Support framer device-tree nodes without '#framer-cells' property - Patch 25 (patch 22 in v4) Fix $ref in the pinctrl subnode Remove '#framer-cells' property Add needed '|' - Patch 26 (patch 23 in v4) Fix a typo in the commit subject - Patches 27, 28, 29 (patch 24, 25, 26 in v4) No changes - Patch 30 (patch 27 in v4) Fix a typo in the commit log - Patch 31 (patch 28 in v4) Used 'fsl,framer' property name instead of 'framer' Changes v3 -> v4 - Patch 21 Fixes build failure with CONFIG_MODULES Changes v2 -> v3 - Patches 1, 2, 3, 4 Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - New patch Remove inline keyword from the existing registers accessors helpers - Patch 6 (patches 5, 27 in v2) Update the binding title Squash patch 27 - Patch 7 (patch 6 in v2) Remove the cast in netdev_to_qmc_hdlc() Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 8 (patch 7 in v2): No change - Patches 9, 10 (patches 8, 9 in v2) Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 11 (patch 10 in v2) Remove inline keyword from the introduced qmc_clrsetbits16() helper Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patches 12, 13, 14, 15, 16, 17, 18, 19, 20 Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 21 (patch 20 in v2) Remove unneeded framer NULL pointer check Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 22 (patch 21 in v2) Change sclkr and sclkx clocks description Remove the framer phandle property from the framer subnodes (ie. from framer-codec nodes) - Patch 23 (patch 22 in v2) Initialize 'disabled' variable at declaration Fix commit log Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 24 (patch 23 in v2) Remove inline keyword from the existing registers accessors helpers Use dev_warn_ratelimited() in default interrupt handler Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 25 (patch 24 in v2) Replace #include "linux/bitfield.h" by #include <linux/bitfield.h> Fold the pinctrl anonymous struct into the struct pef2256_pinctrl Update commit log Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 26 (patch 25 in v2) Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 27 (patch 26 in v2) Fix error message Changed the ch.max computation in framer_dai_hw_rule_channels_by_format() Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' - Patch 28 Add 'Reviewed-by: Christophe Leroy <christophe.leroy(a)csgroup.eu>' Changes v1 -> v2 - Patches 1, 2 (New in v2) Fix __iomem addresses declaration - Patch 19 (17 in v1) Fix a compilation warning - Patch 26 (24 in v1) Fix a typo in Kconfig file Fix issues raised by sparse (make C=1) Herve Codina (27): soc: fsl: cpm1: tsa: Fix __iomem addresses declaration soc: fsl: cpm1: qmc: Fix __iomem addresses declaration soc: fsl: cpm1: qmc: Fix rx channel reset soc: fsl: cpm1: qmc: Extend the API to provide Rx status soc: fsl: cpm1: qmc: Remove inline function specifiers soc: fsl: cpm1: qmc: Add support for child devices net: wan: Add support for QMC HDLC MAINTAINERS: Add the Freescale QMC HDLC driver entry soc: fsl: cpm1: qmc: Introduce available timeslots masks soc: fsl: cpm1: qmc: Rename qmc_setup_tsa* to qmc_init_tsa* soc: fsl: cpm1: qmc: Introduce qmc_chan_setup_tsa* soc: fsl: cpm1: qmc: Remove no more needed checks from qmc_check_chans() soc: fsl: cpm1: qmc: Check available timeslots in qmc_check_chans() soc: fsl: cpm1: qmc: Add support for disabling channel TSA entries soc: fsl: cpm1: qmc: Split Tx and Rx TSA entries setup soc: fsl: cpm1: qmc: Introduce is_tsa_64rxtx flag soc: fsl: cpm1: qmc: Handle timeslot entries at channel start() and stop() soc: fsl: cpm1: qmc: Remove timeslots handling from setup_chan() soc: fsl: cpm1: qmc: Introduce functions to change timeslots at runtime wan: qmc_hdlc: Add runtime timeslots changes support net: wan: Add framer framework support dt-bindings: net: Add the Lantiq PEF2256 E1/T1/J1 framer net: wan: framer: Add support for the Lantiq PEF2256 framer pinctrl: Add support for the Lantic PEF2256 pinmux MAINTAINERS: Add the Lantiq PEF2256 driver entry ASoC: codecs: Add support for the framer codec net: wan: fsl_qmc_hdlc: Add framer support .../bindings/net/lantiq,pef2256.yaml | 213 +++++ MAINTAINERS | 15 + drivers/net/wan/Kconfig | 14 + drivers/net/wan/Makefile | 3 + drivers/net/wan/framer/Kconfig | 41 + drivers/net/wan/framer/Makefile | 7 + drivers/net/wan/framer/framer-core.c | 882 ++++++++++++++++++ drivers/net/wan/framer/pef2256/Makefile | 8 + drivers/net/wan/framer/pef2256/pef2256-regs.h | 250 +++++ drivers/net/wan/framer/pef2256/pef2256.c | 880 +++++++++++++++++ drivers/net/wan/fsl_qmc_hdlc.c | 820 ++++++++++++++++ drivers/pinctrl/Kconfig | 15 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-pef2256.c | 358 +++++++ drivers/soc/fsl/qe/qmc.c | 592 +++++++++--- drivers/soc/fsl/qe/tsa.c | 22 +- include/linux/framer/framer-provider.h | 194 ++++ include/linux/framer/framer.h | 205 ++++ include/linux/framer/pef2256.h | 31 + include/soc/fsl/qe/qmc.h | 27 +- sound/soc/codecs/Kconfig | 15 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/framer-codec.c | 413 ++++++++ sound/soc/fsl/fsl_qmc_audio.c | 2 +- 24 files changed, 4873 insertions(+), 137 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/lantiq,pef2256.yaml create mode 100644 drivers/net/wan/framer/Kconfig create mode 100644 drivers/net/wan/framer/Makefile create mode 100644 drivers/net/wan/framer/framer-core.c create mode 100644 drivers/net/wan/framer/pef2256/Makefile create mode 100644 drivers/net/wan/framer/pef2256/pef2256-regs.h create mode 100644 drivers/net/wan/framer/pef2256/pef2256.c create mode 100644 drivers/net/wan/fsl_qmc_hdlc.c create mode 100644 drivers/pinctrl/pinctrl-pef2256.c create mode 100644 include/linux/framer/framer-provider.h create mode 100644 include/linux/framer/framer.h create mode 100644 include/linux/framer/pef2256.h create mode 100644 sound/soc/codecs/framer-codec.c -- 2.41.0

6 36