October 2020 - Alsa-devel - mailman.alsa-project.org

[PATCH] ASoC: fsl_spdif: Remove unused np
by Mark Brown 02 Oct '20

02 Oct '20

Reported-by: Stephen Rothwell <sfr(a)canb.auug.org.au> Signed-off-by: Mark Brown <broonie(a)kernel.org> --- sound/soc/fsl/fsl_spdif.c | 1 - 1 file changed, 1 deletion(-) diff --git a/sound/soc/fsl/fsl_spdif.c b/sound/soc/fsl/fsl_spdif.c index 9c5607780590..b0f643fefe1e 100644 --- a/sound/soc/fsl/fsl_spdif.c +++ b/sound/soc/fsl/fsl_spdif.c @@ -1252,7 +1252,6 @@ static int fsl_spdif_probe_txclk(struct fsl_spdif_priv *spdif_priv, static int fsl_spdif_probe(struct platform_device *pdev) { - struct device_node *np = pdev->dev.of_node; struct fsl_spdif_priv *spdif_priv; struct spdif_mixer_control *ctrl; struct resource *res; -- 2.20.1

1 1

[PATCH 0/2] Add driver for Microchip S/PDIF RX
by Codrin Ciubotariu 02 Oct '20

02 Oct '20

The Sony/Philips Digital Interface Receiver (SPDIFRX) is a serial port compliant with the IEC-60958 standard. Among its caracteristics, we mention the following: - SPDIF/AES-EBU Compatible Serial Port - 32 Samples FIFO - Data Width Configurable to 24 bits, 20 bits or 16 bits - Packed and Unpacked Data Support for System Memory Optimization - Line State Events Report and Source of Interrupt - Line Error Rate Report - Full Memory Map of 192 bits for Channel 1 and Channel 2 Status and User Data - First 32-bit Status A, Status B Change Report and Source of Interrupt - Line Digital Filter - Register Write Protection - Abnormal Software Access and Internal Sequencer Integrity Check Reports This interface is available in Microchip's SAMA7G5 SoC. Codrin Ciubotariu (2): dt-bindings: sound: add DT bindings for Microchip S/PDIF RX Controller ASoC: mchp-spdifrx: add driver for SPDIF RX .../bindings/sound/mchp,spdifrx.yaml | 73 ++ sound/soc/atmel/Kconfig | 13 + sound/soc/atmel/Makefile | 2 + sound/soc/atmel/mchp-spdifrx.c | 954 ++++++++++++++++++ 4 files changed, 1042 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/mchp,spdifrx.yaml create mode 100644 sound/soc/atmel/mchp-spdifrx.c -- 2.25.1

2 3

[PATCH v10 00/14] ASoC: Intel: Catpt - Lynx and Wildcat point
by Cezary Rojewski 02 Oct '20

02 Oct '20

Implement support for Lynxpoint and Wildcat Point AudioDSP. Catpt solution deprecates existing sound/soc/intel/haswell which is removed in the following series. Due to high range of errors and desynchronization from recommendations set by Windows solution, re-write came as a lower-cost solution compared to refactoring /haswell/ with several series of patches. Series is dependent on linux-spi change: spi: pxa2xx: Add SSC2 and SSPSP2 SSP registers https://www.spinics.net/lists/linux-spi/msg23885.html which has been already merged and is now part of linux-spi tree. Bulk of series content is device driver core code - everything up to patch 7/14 - with fs entries and trace macros introduced right after. While each core patch is shaped in such a way that no unavailable members are ever called, until patch 14/14 is applied, no code compilation can occur as no Makefile is present. Once said patch is added, Makefile and Kconfig are implemented and driver module compiles as expected. Special thanks go to Marcin Barlik and Piotr Papierkowski for sharing their LPT/WPT AudioDSP architecture expertise as well as helping backtrack its historical background. My thanks go to Amadeusz Slawinski for reviews and improvements proposed on and off the internal list. Most of internal diff below is his contribution. Krzysztof Hejmowski helped me setup my own Xtensa environment and recompile LPT/WPT FW binary sources what sped up the development greatly. This would not have been possible without help from these champions, especially considering how quickly the catpt was written: 2 weeks features, 3 weeks optimizations. Thank you. Userspace-exposed members are compatible with what is exposed by deprecated solution as well as FW binary being re-used thus no harm is done. The only visible differences are: the newly added 'Loopback Mute' kcontrol and volume support extending to quad from stereo. On top of fixing erros and design flows, catpt also adds module reload, dynamic SRAM memory allocation during PCM runtime and exposes missing userspace API: 'Loopback Mute' kcontrol, quad volume controls and sysfs fw-version entries. Event tracing is provided to ease solution debugging. Following are not included in this update and are scheduled as later addition: - fw logging - module (library) support Note: LPT power up/down sequences might get aligned with WPT once enough testing is done as capabilities are shared for both DSPs. Note #2: Both LPT and WPT power up/down sequences may get optimized in future updates as thanks to help from the Windows team, most of nuances behind why/what/when in regard to hw registers have been backtracked and reviewed again. Link to developer's deep dive message: https://www.spinics.net/lists/alsa-devel/msg113563.html Changes in v10: - reverted DUAL_MONO case relocation from v9 - indented all constants of enum catpt_module_id to the same column - new newline appended for return path of catpt_dsp_do_send_msg() Changes in v9: https://www.spinics.net/lists/alsa-devel/msg116305.html - fixed newlines in sysfs as requested by Andy, left tags as no other changes done - removed volume_map and replaced by simple formulas for volume kcontrol calculations - removed redundant parentheses in catpt_get_channel_map() and relocated DUAL_MONO case - runtime suspend no longer called during module unload - removed redundant size checks for catpt_dsp_send_tx() and catpt_dsp_copy_rx() Changes in v8: https://www.spinics.net/lists/alsa-devel/msg116168.html - updated catpt_arrange_page_table() with GENMASK and U32_MAX usage - made use of PFN_DOWN() replacing explicit right shitfs by PAGE_SIZE - made fw hash dumping in catpt_coredump() more readable and removed hardcodes - catpt_coredump() dumps fw hash now only if said segment has been found within fw_info - shortened _MSECS suffixes to _MS - IPC structs no longer contain enum members - simplified definition of catpt_set_dspvol() Changes in v7: https://www.spinics.net/lists/alsa-devel/msg116019.html - fixed licence header for fs.c - renamed fs.c to sysfs.c to better match its purpose - added documentation within Documentation/ABI/testing for entries exposed by catpt - bin_attribute fw_build replaced by attribute fw_info: fw_info contains full FW information and after successful handshake, it's always available (stored in driver data) so no need to invoke GET_FW_VERSION IPC again, just dump the stored information - rather than manually creating and removing sysfs files, now makes use of dev_groups member of struct device_driver - patch: 10/14 'ASoC: Intel: Select catpt and deprecate haswell' has been moved to the back of the list: enable catpt after machine boards have been prepared for it first - improved readability of several goto labels Changes in v6: https://www.spinics.net/lists/alsa-devel/msg115765.html - reordered and reorganized code for patches 1/13 - 8/13 of v5, so each patches makes use of no member or function which is unavailable to it. Series size increased from 13 to 14 patches: addition of base members e.g.: registers has been split from addition of device.c file which describes acpi device behavior Changes in v5: https://www.spinics.net/lists/alsa-devel/msg115621.html Basically everything below is result of Andy's review. Thank you Andy for taking time into this detailed review - catpt now makes use of common linux/pxa2xx_ssp.h header file, removing redundant SSP register declarations in the process. As stated in the opening, this is dependent upon linux-spi change: spi: pxa2xx: Add SSC2 and SSPSP2 SSP registers - updated Kconfig by removing DMADEVICES and adding COMPILE_TEST as optional depends-on - updated all register macros definitions to be more safe against common arithmetics when specifying macro's parameters - removed CONFIG_PM and CONFIG_PM_SLEEP usage in favor of __maybe_unused - all 'if (ret < 0)' converted to simple 'if (ret)' whenever possible - fixed erroneous check for platform_device_register_data within catpt_register_board() - _SLAVE/_MASTER replaced with more inclusive _CONSUMER/_PROVIDER for enum catpt_ssp_mode - catpt_acpi_probe() is now making use of high-level wrappers for ioremapping and resource assignment, reducing function's code size - due to improved catpt_acpi_probe() behavior, catpt_acpi_remove() needs not to cast dma_free_coherent() any longer - DMA source and destrination maxburst now of value 16, see: https://www.spinics.net/lists/alsa-devel/msg114394.html - simplified catpt_dsp_update_lpclock() as list_for_each_entry() is empty-safe by default - dropped '_SSP_' from all names of all CATPT_SSP_SSXXX_DEFAULT macros - catpt_updatel_pci now makes use of linux/pci.h and uapi/linux/pci.h constants such as: PCI_PM_CTRL_STATE_MASK and PCI_D3hot Changes in v4: https://www.spinics.net/lists/alsa-devel/msg113762.html - fixed compilation with i386 kconfig (conflicting names) - streamlined naming for SHIM and PCI registers to match SSP ones (SHIM_REG -> SHIM) - catpt_component_probe removed and kcontrols again initializzed statically via snd_kcontrol_new array: this is to remove kctl->id.device shenanigans - renamed catpt_set_ctlvol to catpt_set_dspvol - function name wasn't matching its purpose Changes in v3: - fixed IRAM mask usage in lpt_dsp_power_up (dsp.c) - updated dbg message formatting in catpt_restore_fwimage as suggested by Andy - fixed alignment for struct catpt_ssp_device_format - catpt_set_ctlvol now verifies all-equal scenario based on all channels rather than just first two as requested by Amadeo - fixed SPDX for registers.h Changes in v2: https://www.spinics.net/lists/alsa-devel/msg113660.html - fixed SPDX formatting for all header files as well as pcm.c - fixed size provided to memcpy() in fw_build_read() as reported by Mark - renamed struct catpt_pdata to struct catpt_spec (cosmetic) - fixed erroneous path in catpt_load_block: region is properly released - trace.h events for updating registers have been removed and usages replaced by dev_dbg (SRAMPGE/ LPCS) - as requested by Andy, struct resource has replaced struct catpt_mbank and struct catpt_mregion. This change cascaded into: - catpt_mbank_size and catpt_mregion_size replaced by resource_size - catpt_mregion_intersects replaced by resource_overlaps - all catpt_mbank_ and catpt_mregion_ handlers found in loader.c (_request, _reserve, _release, _extract, _split, _join) have been removed - __request_region and __release_region have been enlisted in their place - catpt_mregion_intersecting renamed to catpt_resource_overlapping - catpt_request_region helper has been provided to deal with -size based requests o haven't found direct replacements in resource.c/ ioport.h for both functions - catpt_mbank_create and catpt_mbank_remove renamed to catpt_sram_init and catpt_sram_free respectively - catpt_sram_init now returns void instead of int and has been converted to simple initialized. This change ultimately cascaded into: o both SRAM banks initialization being moved to catpt_dev_init from catpt_acpi_probe (device.c) o catpt_dev::spec is now initialized first, with catpt_dev_init following it soon after o catpt_acpi_probe erroneous path has been simplified as SRAM banks no longer need to be freed - catpt_sram_free now frees all resources via child -> sibling enumeration rather than region_list iteration - catpt_dsp_update_srampge and catpt_dsp_set_srampge now accept new argument: unsigned long mask. Caused by removal of catpt_mbank - mask is taken directly from catpt_dev::spec::d/iram_mask - trace.h events for catpt_mbank and catpt_mregion have been removed Diff against last drop on internal list: https://www.spinics.net/lists/alsa-devel/msg113549.html - replaced spinlock with mutex for mregion allocation and release to address sleeping in atomic context warnings - fixed coredump fw_hash dumping - kcontrol values are now always stored regardless of stream of interest is running or not - kcontrol values are now applied after stream is prepared instead of ignoring what has been set by user initially - catpt_pdata instances have been renamed from hsw_ and bdw_ to lpt_ and wpt_ respectively - reordered Makefile .o(s) (cosmetic) Cezary Rojewski (14): ASoC: Intel: Add catpt base members ASoC: Intel: catpt: Implement IPC protocol ASoC: Intel: catpt: Add IPC message handlers ASoC: Intel: catpt: Define DSP operations ASoC: Intel: catpt: Firmware loading and context restore ASoC: Intel: catpt: PCM operations ASoC: Intel: catpt: Device driver lifecycle ASoC: Intel: catpt: Event tracing ASoC: Intel: catpt: Simple sysfs attributes ASoC: Intel: haswell: Remove haswell-solution specific code ASoC: Intel: broadwell: Remove haswell-solution specific code ASoC: Intel: bdw-5650: Remove haswell-solution specific code ASoC: Intel: bdw-5677: Remove haswell-solution specific code ASoC: Intel: Select catpt and deprecate haswell .../ABI/testing/sysfs-bus-pci-devices-catpt | 16 + sound/soc/intel/Kconfig | 24 +- sound/soc/intel/Makefile | 2 +- sound/soc/intel/boards/Kconfig | 8 +- sound/soc/intel/boards/bdw-rt5650.c | 36 - sound/soc/intel/boards/bdw-rt5677.c | 33 - sound/soc/intel/boards/broadwell.c | 33 - sound/soc/intel/boards/haswell.c | 28 +- sound/soc/intel/catpt/Makefile | 6 + sound/soc/intel/catpt/core.h | 188 +++ sound/soc/intel/catpt/device.c | 352 +++++ sound/soc/intel/catpt/dsp.c | 578 ++++++++ sound/soc/intel/catpt/ipc.c | 298 +++++ sound/soc/intel/catpt/loader.c | 671 ++++++++++ sound/soc/intel/catpt/messages.c | 313 +++++ sound/soc/intel/catpt/messages.h | 401 ++++++ sound/soc/intel/catpt/pcm.c | 1175 +++++++++++++++++ sound/soc/intel/catpt/registers.h | 178 +++ sound/soc/intel/catpt/sysfs.c | 55 + sound/soc/intel/catpt/trace.h | 83 ++ 20 files changed, 4335 insertions(+), 143 deletions(-) create mode 100644 Documentation/ABI/testing/sysfs-bus-pci-devices-catpt create mode 100644 sound/soc/intel/catpt/Makefile create mode 100644 sound/soc/intel/catpt/core.h create mode 100644 sound/soc/intel/catpt/device.c create mode 100644 sound/soc/intel/catpt/dsp.c create mode 100644 sound/soc/intel/catpt/ipc.c create mode 100644 sound/soc/intel/catpt/loader.c create mode 100644 sound/soc/intel/catpt/messages.c create mode 100644 sound/soc/intel/catpt/messages.h create mode 100644 sound/soc/intel/catpt/pcm.c create mode 100644 sound/soc/intel/catpt/registers.h create mode 100644 sound/soc/intel/catpt/sysfs.c create mode 100644 sound/soc/intel/catpt/trace.h -- 2.17.1

4 20

[PATCH] ASoC: wm8523: Fix a typo in a comment
by Christophe JAILLET 02 Oct '20

02 Oct '20

It is likely that this header file is about the WM8523. Signed-off-by: Christophe JAILLET <christophe.jaillet(a)wanadoo.fr> --- sound/soc/codecs/wm8523.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/soc/codecs/wm8523.h b/sound/soc/codecs/wm8523.h index 79afbf1e4f1a..5f9bb3df1866 100644 --- a/sound/soc/codecs/wm8523.h +++ b/sound/soc/codecs/wm8523.h @@ -1,6 +1,6 @@ /* SPDX-License-Identifier: GPL-2.0-only */ /* - * wm8523.h -- WM8423 ASoC driver + * wm8523.h -- WM8523 ASoC driver * * Copyright 2009 Wolfson Microelectronics, plc * -- 2.25.1

2 1

[PATCH] ALSA: hda/realtek - Add mute Led support for HP Elitebook 845 G7
by Qiu Wenbo 02 Oct '20

02 Oct '20

After installing archlinux, the mute led and micmute led are not working at all. This patch fix this issue by applying a fixup from similar model. These mute leds are confirmed working on HP Elitebook 845 G7. Signed-off-by: Qiu Wenbo <qiuwenbo(a)kylinos.com.cn> --- sound/pci/hda/patch_realtek.c | 1 + 1 file changed, 1 insertion(+) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index d4f17b465892..8239c4dd4a90 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -7763,6 +7763,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x869d, "HP", ALC236_FIXUP_HP_MUTE_LED), SND_PCI_QUIRK(0x103c, 0x8729, "HP", ALC285_FIXUP_HP_GPIO_LED), SND_PCI_QUIRK(0x103c, 0x8736, "HP", ALC285_FIXUP_HP_GPIO_AMP_INIT), + SND_PCI_QUIRK(0x103c, 0x8760, "HP", ALC285_FIXUP_HP_MUTE_LED), SND_PCI_QUIRK(0x103c, 0x877a, "HP", ALC285_FIXUP_HP_MUTE_LED), SND_PCI_QUIRK(0x103c, 0x877d, "HP", ALC236_FIXUP_HP_MUTE_LED), SND_PCI_QUIRK(0x1043, 0x103e, "ASUS X540SA", ALC256_FIXUP_ASUS_MIC), -- 2.28.0

2 1

[PATCH 1/2] dt-bindings: tas2764: Add the TAS2764 binding doc
by Dan Murphy 02 Oct '20

02 Oct '20

Add the binding for the TAS2764 Smart Amplifier. Signed-off-by: Dan Murphy <dmurphy(a)ti.com> --- .../devicetree/bindings/sound/tas2764.yaml | 74 +++++++++++++++++++ 1 file changed, 74 insertions(+) create mode 100644 Documentation/devicetree/bindings/sound/tas2764.yaml diff --git a/Documentation/devicetree/bindings/sound/tas2764.yaml b/Documentation/devicetree/bindings/sound/tas2764.yaml new file mode 100644 index 000000000000..4e758ff81003 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tas2764.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/sound/tas2764.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Texas Instruments TAS2764 Smart PA + +maintainers: + - Dan Murphy <dmurphy(a)ti.com> + +description: | + The TAS2764 is a mono, digital input Class-D audio amplifier optimized for + efficiently driving high peak power into small loudspeakers. + Integrated speaker voltage and current sense provides for + real time monitoring of loudspeaker behavior. + +properties: + compatible: + enum: + - ti,tas2764 + + reg: + maxItems: 1 + description: | + I2C address of the device can be between 0x38 to 0x45. + + reset-gpio: + description: GPIO used to reset the device. + + shutdown-gpios: + description: GPIO used to control the state of the device. + + interrupts: + maxItems: 1 + + ti,imon-slot-no: + $ref: /schemas/types.yaml#/definitions/uint32 + description: TDM TX current sense time slot. + + ti,vmon-slot-no: + $ref: /schemas/types.yaml#/definitions/uint32 + description: TDM TX voltage sense time slot. + + '#sound-dai-cells': + const: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + codec: codec@38 { + compatible = "ti,tas2764"; + reg = <0x38>; + #sound-dai-cells = <1>; + interrupt-parent = <&gpio1>; + interrupts = <14>; + reset-gpio = <&gpio1 15 0>; + shutdown-gpios = <&gpio1 15 0>; + ti,imon-slot-no = <0>; + ti,vmon-slot-no = <2>; + }; + }; + +... -- 2.28.0.585.ge1cfff676549

2 4

[alsa-devel] [PATCH] ALSA: usb-audio: fix spelling mistake "Frequence" -> "Frequency"
by Colin King 02 Oct '20

02 Oct '20

From: Colin Ian King <colin.king(a)canonical.com> There are spelling mistakes in equalizer name fields, fix them. Signed-off-by: Colin Ian King <colin.king(a)canonical.com> --- sound/usb/mixer_us16x08.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/sound/usb/mixer_us16x08.c b/sound/usb/mixer_us16x08.c index 26ed23b18b77..4f594f9552a8 100644 --- a/sound/usb/mixer_us16x08.c +++ b/sound/usb/mixer_us16x08.c @@ -1119,7 +1119,7 @@ static const struct snd_us16x08_control_params eq_controls[] = { .control_id = SND_US16X08_ID_EQLOWFREQ, .type = USB_MIXER_U8, .num_channels = 16, - .name = "EQ Low Frequence", + .name = "EQ Low Frequency", }, { /* EQ mid low gain */ .kcontrol_new = &snd_us16x08_eq_gain_ctl, @@ -1133,7 +1133,7 @@ static const struct snd_us16x08_control_params eq_controls[] = { .control_id = SND_US16X08_ID_EQLOWMIDFREQ, .type = USB_MIXER_U8, .num_channels = 16, - .name = "EQ MidLow Frequence", + .name = "EQ MidLow Frequency", }, { /* EQ mid low Q */ .kcontrol_new = &snd_us16x08_eq_mid_width_ctl, @@ -1154,7 +1154,7 @@ static const struct snd_us16x08_control_params eq_controls[] = { .control_id = SND_US16X08_ID_EQHIGHMIDFREQ, .type = USB_MIXER_U8, .num_channels = 16, - .name = "EQ MidHigh Frequence", + .name = "EQ MidHigh Frequency", }, { /* EQ mid high Q */ .kcontrol_new = &snd_us16x08_eq_mid_width_ctl, @@ -1175,7 +1175,7 @@ static const struct snd_us16x08_control_params eq_controls[] = { .control_id = SND_US16X08_ID_EQHIGHFREQ, .type = USB_MIXER_U8, .num_channels = 16, - .name = "EQ High Frequence", + .name = "EQ High Frequency", }, }; -- 2.19.1

3 3

alsactl: init - add -U option to disable UCM based init
by GitHub pull_request - edited 02 Oct '20

02 Oct '20

alsa-project/alsa-utils pull request #60 was edited from ahlinc: The reason is to use it with internal init extra commands like: alsactl -U -E CMD=info init Currently, if there is a valid UCM config for a card the alsactl command exits silently on the init command and don't execute any extra commands because that commands defined in a common init path file _init/00main_ that don't used in case of UCM did the job. Request URL : https://github.com/alsa-project/alsa-utils/pull/60 Patch URL : https://github.com/alsa-project/alsa-utils/pull/60.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

alsactl: init - add -U option to disable UCM based init
by GitHub pull_request - opened 02 Oct '20

02 Oct '20

alsa-project/alsa-utils pull request #60 was opened from ahlinc: The reason is to use it with internal init extra commands like: alsactl -U -E CMD=info init Currently, if there is a valid UCM config for a card the alsactl command exits silently on the init command and don't execute any extra commands because that commands defined in common init path file _init/00main_ that don't used in case of UCM did the job. Request URL : https://github.com/alsa-project/alsa-utils/pull/60 Patch URL : https://github.com/alsa-project/alsa-utils/pull/60.patch Repository URL: https://github.com/alsa-project/alsa-utils

1 0

[PATCH] ASoC: soc-pcm: ignore un-needed mutex_unlock() case on soc_pcm_open()
by Kuninori Morimoto 02 Oct '20

02 Oct '20

From: Kuninori Morimoto <kuninori.morimoto.gx(a)renesas.com> commit 140a4532cdb8c ("ASoC: soc-pcm: add soc_pcm_clean() and call it from soc_pcm_open/close()") switch to call soc_pcm_clean() on soc_pcm_open() when rollback case. But, it uses "goto err" (A) *before* mutex_lock() (B) when error of snd_soc_pcm_component_pm_runtime_get(). The mutex_unlock() (C) is not needed in such case. This patch fix it. static int soc_pcm_open(...) { ... ret = snd_soc_pcm_component_pm_runtime_get(rtd, substream); if (ret < 0) (A) goto err; (B) mutex_lock_nested(...); ... err: (C) mutex_unlock(..); ... } Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx(a)renesas.com> --- sound/soc/soc-pcm.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/sound/soc/soc-pcm.c b/sound/soc/soc-pcm.c index 09e8d703a502..5d538520e2cf 100644 --- a/sound/soc/soc-pcm.c +++ b/sound/soc/soc-pcm.c @@ -706,7 +706,7 @@ static int soc_pcm_open(struct snd_pcm_substream *substream) ret = snd_soc_pcm_component_pm_runtime_get(rtd, substream); if (ret < 0) - goto err; + goto pm_err; mutex_lock_nested(&rtd->card->pcm_mutex, rtd->card->pcm_subclass); @@ -786,7 +786,7 @@ static int soc_pcm_open(struct snd_pcm_substream *substream) snd_soc_runtime_activate(rtd, substream->stream); err: mutex_unlock(&rtd->card->pcm_mutex); - +pm_err: if (ret < 0) soc_pcm_clean(substream, 1); -- 2.25.1

2 1