November 2017 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] [RFC v1] ALSA: xen-front: Add Xen para-virtualized frontend driver
by Oleksandr Andrushchenko 22 Dec '17

22 Dec '17

Hi, all! Foreword ======== This RFC is aimed to introduce support of para-virtualized sound frontend driver for Xen [1] and gather opinions from the relevant communities (ALSA, Xen). It implements the protocol from [2] with the following limitations: - mute/unmute is not supported - get/set volume is not supported Volume control is not supported for the reason that most of the use-cases (at the moment) are based on scenarios where unprivileged OS (e.g. Android, AGL etc) uses software mixers. Both capture and playback are supported. The relevant backend is implemented as a user-space application [3] and uses accompanying helper library [4]. Both frontend driver and backend were tested on real HW running Xen hypervisor (Renesas R-Car ARM based H3/M3 boards, x86). Discussion ========== During the first attempt to upstream the driver [5] number of comments and concerns were raised, one of the biggest flaws in the design were questioned by both Clemens Ladisch [6] and Takashi Sakamoto [7]: the absence of synchronization between frontend and backend during capture/playback. Two options were discussed: “In design of ALSA PCM core, drivers are expected to synchronize to actual hardwares for semi-realtime data transmission. The synchronization is done by two points: 1) Interrupts to respond events from actual hardwares. 2) Positions of actual data transmission in any serial sound interfaces of actual hardwares. “ and finally a change to the existing protocol was suggested: “In 'include/xen/interface/io/sndif.h', there's no functionalities I described the above: 1. notifications from DomU to Dom0 about the size of period for interrupts from actual hardwares. Or no way from Dom0 to DomU about the configured size of the period. 2. notifications of the interrupts from actual hardwares to DomU.” This is implemented as a change to the sndif protocol [8] and allows removing period emulation: 1. Introduced a new event channel from back to front 2. New event with number of bytes played/captured (XENSND_EVT_CUR_POS, to be used for sending snd_pcm_period_elapsed at frontend (in Linux implementation). Sent in bytes, not frames to make the protocol generic and consistent) 3. New request for playback/capture control (XENSND_OP_TRIGGER) with start/pause/stop/resume sub-ops. Along with these changes other comments on the driver were addressed, e.g. split into smaller chunks, moved the driver from misc to xen etc. Hope, this helps to get the full picture of what was discussed and makes it possible to move forward. Waiting for your valuable comments, Thank you, Oleksandr [1] https://github.com/andr2000/linux/commits/snd_upstream_v1 [2] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/inc… [3] https://github.com/xen-troops/snd_be [4] https://github.com/xen-troops/libxenbe [5] https://lkml.org/lkml/2017/8/7/363 [6] http://mailman.alsa-project.org/pipermail/alsa-devel/2017-August/123617.html [7] http://mailman.alsa-project.org/pipermail/alsa-devel/2017-August/123744.html [8] https://github.com/andr2000/linux/commit/095d7feae00bf00c852c67c4f1044de560…

3 6

[alsa-devel] [PATCH] ASoC: rl6231: get better PLL parameters
by Bard Liao 19 Dec '17

19 Dec '17

For those which can only get approximation PLL out cases, this patch will use higher resolution to get a better PLL parameter. Signed-off-by: Bard Liao <bardliao(a)realtek.com> --- sound/soc/codecs/rl6231.c | 95 ++++++++++++++++++++++++++++++++--------------- 1 file changed, 66 insertions(+), 29 deletions(-) diff --git a/sound/soc/codecs/rl6231.c b/sound/soc/codecs/rl6231.c index 974a904..33690e9 100644 --- a/sound/soc/codecs/rl6231.c +++ b/sound/soc/codecs/rl6231.c @@ -13,6 +13,7 @@ #include <linux/module.h> #include <linux/regmap.h> +#include <linux/gcd.h> #include "rl6231.h" /** @@ -106,6 +107,25 @@ static const struct pll_calc_map pll_preset_table[] = { {19200000, 24576000, 3, 30, 3, false}, }; +static unsigned int find_best_div(unsigned int in, + unsigned int max, unsigned int div) +{ + unsigned int d; + + if (in <= max) + return 1; + + d = in / max; + if (in % max) + d++; + + while (div % d != 0) + d++; + + + return d; +} + /** * rl6231_pll_calc - Calcualte PLL M/N/K code. * @freq_in: external clock provided to codec. @@ -120,9 +140,11 @@ int rl6231_pll_calc(const unsigned int freq_in, const unsigned int freq_out, struct rl6231_pll_code *pll_code) { int max_n = RL6231_PLL_N_MAX, max_m = RL6231_PLL_M_MAX; - int i, k, red, n_t, pll_out, in_t, out_t; - int n = 0, m = 0, m_t = 0; - int red_t = abs(freq_out - freq_in); + int i, k, n_t; + int k_t, min_k, max_k, n = 0, m = 0, m_t = 0; + unsigned int red, pll_out, in_t, out_t, div, div_t; + unsigned int red_t = abs(freq_out - freq_in); + unsigned int f_in, f_out, f_max; bool bypass = false; if (RL6231_PLL_INP_MAX < freq_in || RL6231_PLL_INP_MIN > freq_in) @@ -140,39 +162,54 @@ int rl6231_pll_calc(const unsigned int freq_in, } } - k = 100000000 / freq_out - 2; - if (k > RL6231_PLL_K_MAX) - k = RL6231_PLL_K_MAX; - for (n_t = 0; n_t <= max_n; n_t++) { - in_t = freq_in / (k + 2); - pll_out = freq_out / (n_t + 2); - if (in_t < 0) - continue; - if (in_t == pll_out) { - bypass = true; - n = n_t; - goto code_find; - } - red = abs(in_t - pll_out); - if (red < red_t) { - bypass = true; - n = n_t; - m = m_t; - if (red == 0) + min_k = 80000000 / freq_out - 2; + max_k = 150000000 / freq_out - 2; + if (max_k > RL6231_PLL_K_MAX) + max_k = RL6231_PLL_K_MAX; + if (min_k > RL6231_PLL_K_MAX) + min_k = max_k = RL6231_PLL_K_MAX; + div_t = gcd(freq_in, freq_out); + f_max = 0xffffffff / RL6231_PLL_N_MAX; + div = find_best_div(freq_in, f_max, div_t); + f_in = freq_in / div; + f_out = freq_out / div; + k = min_k; + for (k_t = min_k; k_t <= max_k; k_t++) { + for (n_t = 0; n_t <= max_n; n_t++) { + in_t = f_in * (n_t + 2); + pll_out = f_out * (k_t + 2); + if (in_t < 0) + continue; + if (in_t == pll_out) { + bypass = true; + n = n_t; + k = k_t; goto code_find; - red_t = red; - } - for (m_t = 0; m_t <= max_m; m_t++) { - out_t = in_t / (m_t + 2); - red = abs(out_t - pll_out); + } + out_t = in_t / (k_t + 2); + red = abs(f_out - out_t); if (red < red_t) { - bypass = false; + bypass = true; n = n_t; - m = m_t; + m = 0; + k = k_t; if (red == 0) goto code_find; red_t = red; } + for (m_t = 0; m_t <= max_m; m_t++) { + out_t = in_t / ((m_t + 2) * (k_t + 2)); + red = abs(f_out - out_t); + if (red < red_t) { + bypass = false; + n = n_t; + m = m_t; + k = k_t; + if (red == 0) + goto code_find; + red_t = red; + } + } } } pr_debug("Only get approximation about PLL\n"); -- 2.7.4

2 1

[alsa-devel] [PATCH v3 0/5] TDA1997x HDMI video receiver
by Tim Harvey 19 Dec '17

19 Dec '17

This is a v4l2 subdev driver supporting the TDA1997x HDMI video receiver. I've tested this on a Gateworks GW54xx with an IMX6Q which uses the TDA19971 with 16bits connected to the IMX6 CSI. For this configuration I've tested both 16bit YUV422 and 8bit BT656 mode. While the driver should support the TDA1993 I do not have one for testing. Further potential development efforts include: - CEC support - HDCP support - mbus format selection support for bus widths that support multiple formats - TDA19972 support (2 inputs) History: v3: - fix typo in dt bindings - added dt bindings for GW551x - use V4L2_DV_BT_FRAME_WIDTH/HEIGHT macros - fixed missing break - use only hdmi_infoframe_log for infoframe logging - simplify tda1997x_s_stream error handling - add delayed work proc to handle hotplug enable/disable - fix set_edid (disable HPD before writing, enable after) - remove enabling edid by default - initialize timings - take quant range into account in colorspace conversion - remove vendor/product tracking (we provide this in log_status via infoframes) - add v4l_controls - add more detail to log_status - calculate vhref generator timings - timing detection fixes (rounding errors, hswidth errors) - rename configure_input/configure_conv functions v2: - encorporate feedback into dt bindings - change audio dt bindings - implement dv timings enum/cap - remove deprecated g_mbus_config op - fix dv_query_timings - add EDID get/set handling - remove max-pixel-rate support - add audio codec DAI support - added media-ctl and v4l2-compliance details v1: - initial RFC Media device topology: # media-ctl -d /dev/media0 -p Media controller API version 4.13.0 Media device information ------------------------ driver imx-media model imx-media serial bus info hw revision 0x0 driver version 4.13.0 Device topology - entity 1: adv7180 2-0020 (1 pad, 1 link) type V4L2 subdev subtype Unknown flags 20004 device node name /dev/v4l-subdev0 pad0: Source [fmt:UYVY8_2X8/720x480 field:interlaced colorspace:smpte170m] -> "ipu2_csi1_mux":1 [] - entity 3: tda19971 2-0048 (1 pad, 1 link) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev1 pad0: Source [fmt:UYVY8_1X16/640x480 field:none colorspace:srgb] [dv.caps:BT.656/1120 min:640x480@13000000 max:1920x1080@165000000 stds:CEA-861,DMT caps:progressive] [dv.detect:BT.656/1120 640x480p59 (800x525) stds:CEA-861,DMT flags:has-cea861-vic] [dv.current:BT.656/1120 1920x1080p60 (2200x1125) stds:CEA-861,DMT flags:can-reduce-fps,CE-video,has-cea861-vic] -> "ipu1_csi0_mux":1 [] - entity 5: ipu1_vdic (3 pads, 3 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev2 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu1_csi0":1 [] <- "ipu1_csi1":1 [] pad1: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] pad2: Source [fmt:AYUV8_1X32/640x480@1/60 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prp":0 [] - entity 9: ipu2_vdic (3 pads, 3 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev3 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu2_csi0":1 [] <- "ipu2_csi1":1 [] pad1: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] pad2: Source [fmt:AYUV8_1X32/640x480@1/60 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prp":0 [] - entity 13: ipu1_ic_prp (3 pads, 5 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev4 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu1_vdic":2 [] <- "ipu1_csi0":1 [] <- "ipu1_csi1":1 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prpenc":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prpvf":0 [] - entity 17: ipu1_ic_prpenc (2 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev5 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu1_ic_prp":1 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prpenc capture":0 [] - entity 20: ipu1_ic_prpenc capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video0 pad0: Sink <- "ipu1_ic_prpenc":1 [] - entity 26: ipu1_ic_prpvf (2 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev6 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu1_ic_prp":2 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prpvf capture":0 [] - entity 29: ipu1_ic_prpvf capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video1 pad0: Sink <- "ipu1_ic_prpvf":1 [] - entity 35: ipu2_ic_prp (3 pads, 5 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev7 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu2_vdic":2 [] <- "ipu2_csi0":1 [] <- "ipu2_csi1":1 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prpenc":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prpvf":0 [] - entity 39: ipu2_ic_prpenc (2 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev8 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu2_ic_prp":1 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prpenc capture":0 [] - entity 42: ipu2_ic_prpenc capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video2 pad0: Sink <- "ipu2_ic_prpenc":1 [] - entity 48: ipu2_ic_prpvf (2 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev9 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu2_ic_prp":2 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prpvf capture":0 [] - entity 51: ipu2_ic_prpvf capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video3 pad0: Sink <- "ipu2_ic_prpvf":1 [] - entity 57: ipu1_csi0 (3 pads, 4 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev10 pad0: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480 compose.bounds:(0,0)/640x480 compose:(0,0)/640x480] <- "ipu1_csi0_mux":2 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prp":0 [] -> "ipu1_vdic":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_csi0 capture":0 [] - entity 61: ipu1_csi0 capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video4 pad0: Sink <- "ipu1_csi0":2 [] - entity 67: ipu1_csi1 (3 pads, 3 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev11 pad0: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480 compose.bounds:(0,0)/640x480 compose:(0,0)/640x480] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prp":0 [] -> "ipu1_vdic":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_csi1 capture":0 [] - entity 71: ipu1_csi1 capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video5 pad0: Sink <- "ipu1_csi1":2 [] - entity 77: ipu2_csi0 (3 pads, 3 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev12 pad0: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480 compose.bounds:(0,0)/640x480 compose:(0,0)/640x480] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prp":0 [] -> "ipu2_vdic":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_csi0 capture":0 [] - entity 81: ipu2_csi0 capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video6 pad0: Sink <- "ipu2_csi0":2 [] - entity 87: ipu2_csi1 (3 pads, 4 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev13 pad0: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480 compose.bounds:(0,0)/640x480 compose:(0,0)/640x480] <- "ipu2_csi1_mux":2 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prp":0 [] -> "ipu2_vdic":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_csi1 capture":0 [] - entity 91: ipu2_csi1 capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video7 pad0: Sink <- "ipu2_csi1":2 [] - entity 97: ipu1_csi0_mux (3 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev14 pad0: Sink [fmt:unknown/0x0] pad1: Sink [fmt:unknown/0x0] <- "tda19971 2-0048":0 [] pad2: Source [fmt:unknown/0x0] -> "ipu1_csi0":0 [] - entity 101: ipu2_csi1_mux (3 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev15 pad0: Sink [fmt:unknown/0x0] pad1: Sink [fmt:unknown/0x0] <- "adv7180 2-0020":0 [] pad2: Source [fmt:unknown/0x0] -> "ipu2_csi1":0 [] v4l2-compliance test results: (on /dev/video6 as v4l2-compliance doesn't yet support subdevs) Driver Info: Driver name : imx-media-captu Card type : imx-media-capture Bus info : platform:ipu2_csi0 Driver version: 4.13.0 Capabilities : 0x84200001 Video Capture Streaming Extended Pix Format Device Capabilities Device Caps : 0x04200001 Video Capture Streaming Extended Pix Format Compliance test for device /dev/video6 (not using libv4l2): Required ioctls: test VIDIOC_QUERYCAP: OK Allow for multiple opens: test second video open: OK test VIDIOC_QUERYCAP: OK test VIDIOC_G/S_PRIORITY: OK Debug ioctls: test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) test VIDIOC_LOG_STATUS: OK (Not Supported) Input ioctls: test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported) fail: v4l2-test-input-output.cpp(418): G_INPUT not supported for a capture device test VIDIOC_G/S/ENUMINPUT: FAIL test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 0 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) test VIDIOC_G/S_EDID: OK (Not Supported) Control ioctls: test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK test VIDIOC_QUERYCTRL: OK test VIDIOC_G/S_CTRL: OK fail: v4l2-test-controls.cpp(574): g_ext_ctrls does not support count == 0 test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported) test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 0 Private Controls: 0 Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK test VIDIOC_G/S_PARM: OK test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK test VIDIOC_TRY_FMT: OK test VIDIOC_S_FMT: OK test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported) test Composing: OK (Not Supported) test Scaling: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK test VIDIOC_EXPBUF: OK Test input 0: Total: 42, Succeeded: 40, Failed: 2, Warnings: 0 Tim Harvey (5): MAINTAINERS: add entry for NXP TDA1997x driver media: dt-bindings: Add bindings for TDA1997X media: i2c: Add TDA1997x HDMI receiver driver ARM: dts: imx: Add TDA19971 HDMI Receiver to GW54xx ARM: dts: imx: Add TDA19971 HDMI Receiver to GW551x .../devicetree/bindings/media/i2c/tda1997x.txt | 179 + MAINTAINERS | 8 + arch/arm/boot/dts/imx6q-gw54xx.dts | 102 + arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 29 +- arch/arm/boot/dts/imx6qdl-gw551x.dtsi | 85 + drivers/media/i2c/Kconfig | 9 + drivers/media/i2c/Makefile | 1 + drivers/media/i2c/tda1997x.c | 3485 ++++++++++++++++++++ include/dt-bindings/media/tda1997x.h | 78 + include/media/i2c/tda1997x.h | 53 + 10 files changed, 4026 insertions(+), 3 deletions(-) create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt create mode 100644 drivers/media/i2c/tda1997x.c create mode 100644 include/dt-bindings/media/tda1997x.h create mode 100644 include/media/i2c/tda1997x.h -- 2.7.4

5 22

[alsa-devel] Line6 Helix - usb compliant but not working correct
by Jens Verwiebe 14 Dec '17

14 Dec '17

Hi folks I recently got a Line6 Helix LT which can work usb compliant for example on OSX or IOS. No driver is needed but the samplerate is fixed to 48000 ( which is okay for the first ). Now i expected this device to work ootb in alsa, which turned out to be half the truth. Connecting the device threw " usb 7-2: parse_audio_format_rates_v2(): unable to retrieve number of sample rates (clock 16)" so i investigated a bit and found this workaround: --- "/media/Workdata3/Development/kernel_lowlat_4.4-97/linux-4.4.97/sound/usb/clock (Kopie).c" 2017-11-08 10:06:31.000000000 +0100 +++ /media/Workdata3/Development/kernel_lowlat_4.4-97/linux-4.4.97/sound/usb/clock.c 2017-11-14 23:06:51.750924051 +0100 @@ -361,6 +361,13 @@ static int set_sample_rate_v2(struct snd struct uac_clock_source_descriptor *cs_desc; clock = snd_usb_clock_find_source(chip, fmt->clock, true); + /* + * Line6 HELIX does not respond to sample rate + * set requests. The only valid rate is 48000. + */ + if (chip->usb_id == USB_ID(0x0e41, 0x4244) && rate == 48000) + return 0; + if (clock < 0) return clock; --- "/media/Workdata3/Development/kernel_lowlat_4.4-97/linux-4.4.97/sound/usb/format (Kopie).c" 2017-11-08 10:06:31.000000000 +0100 +++ /media/Workdata3/Development/kernel_lowlat_4.4-97/linux-4.4.97/sound/usb/format.c 2017-11-14 23:12:24.329766243 +0100 @@ -293,6 +293,20 @@ static int parse_audio_format_rates_v2(s int nr_triplets, data_size, ret = 0; int clock = snd_usb_clock_find_source(chip, fp->clock, false); + /* + * Line6 HELIX does not respond to sample rate + * query requests. The only valid rate is 48000. + */ + if (chip->usb_id == USB_ID(0x0e41, 0x4244)) { + fp->nr_rates = 1; + fp->rate_min = 48000; + fp->rate_max = 48000; + fp->rates = SNDRV_PCM_RATE_48000; + fp->rate_table = kmalloc(sizeof(int), GFP_KERNEL); + fp->rate_table[0] = 48000; + return 0; + } + if (clock < 0) { dev_err(&dev->dev, "%s(): unable to find clock source (clock %d)\n", This trick made the device appear in aplay -l and /proc/asound just as expected. [ 7988.495085] usb 7-2: new high-speed USB device number 4 using xhci_hcd [ 7988.663622] usb 7-2: New USB device found, idVendor=0e41, idProduct=4244 [ 7988.663625] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7988.663627] usb 7-2: Product: HELIX [ 7988.663629] usb 7-2: Manufacturer: LINE 6 [ 7988.663630] usb 7-2: SerialNumber: 2744535 But i ended up with sometimes occuring soft clicks in playback which imply i have timing problems. Another symptom is aplay does not output any sound while not throwing any error while in jack i can create the driver just fine. I would apreciate any hint what i could try out here. Greetings from Hamburg ... Jens -- Jens Verwiebe Allerskehre 44 - 22309 Hamburg Tel.: +49 40 68 78 50 mobile: +49 172 400 49 07 mailto: info(a)jensverwiebe.de web: http://www.jensverwiebe.de

2 3

[alsa-devel] [PATCH v4 0/5] TDA1997x HDMI video receiver
by Tim Harvey 14 Dec '17

14 Dec '17

This is a v4l2 subdev driver supporting the TDA1997x HDMI video receiver. I've tested this on a Gateworks GW54xx/GW551x with an IMX6Q which uses the TDA19971 with 16bits connected to the IMX6 CSI. For this configuration I've tested both 16bit YUV422 and 8bit BT656 parallel video bus modes. While the driver should support the TDA1993 I do not have one for testing. Further potential development efforts include: - CEC support - HDCP support - mbus format selection support for bus widths that support multiple formats - TDA19972 support (2 inputs) Media graphs can be found at http://dev.gateworks.com/docs/linux/media History: v4: - move include/dt-bindings/media/tda1997x.h to bindings patch - clarify port node details in bindings - fix typos - fix default quant range for VGA - fix quant range handling and conv matrix - add additional standards and capabilities to timings_cap v3: - fix typo in dt bindings - added dt bindings for GW551x - use V4L2_DV_BT_FRAME_WIDTH/HEIGHT macros - fixed missing break - use only hdmi_infoframe_log for infoframe logging - simplify tda1997x_s_stream error handling - add delayed work proc to handle hotplug enable/disable - fix set_edid (disable HPD before writing, enable after) - remove enabling edid by default - initialize timings - take quant range into account in colorspace conversion - remove vendor/product tracking (we provide this in log_status via infoframes) - add v4l_controls - add more detail to log_status - calculate vhref generator timings - timing detection fixes (rounding errors, hswidth errors) - rename configure_input/configure_conv functions v2: - encorporate feedback into dt bindings - change audio dt bindings - implement dv timings enum/cap - remove deprecated g_mbus_config op - fix dv_query_timings - add EDID get/set handling - remove max-pixel-rate support - add audio codec DAI support - added media-ctl and v4l2-compliance details v1: - initial RFC Media device topology: # media-ctl -d /dev/media0 -p Media controller API version 4.13.0 Media device information ------------------------ driver imx-media model imx-media serial bus info hw revision 0x0 driver version 4.13.0 Device topology - entity 1: adv7180 2-0020 (1 pad, 1 link) type V4L2 subdev subtype Unknown flags 20004 device node name /dev/v4l-subdev0 pad0: Source [fmt:UYVY8_2X8/720x480 field:interlaced colorspace:smpte170m] -> "ipu2_csi1_mux":1 [] - entity 3: tda19971 2-0048 (1 pad, 1 link) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev1 pad0: Source [fmt:UYVY8_1X16/640x480 field:none colorspace:srgb] [dv.caps:BT.656/1120 min:640x480@13000000 max:1920x1080@165000000 stds:CEA-861,DMT caps:progressive] [dv.detect:BT.656/1120 640x480p59 (800x525) stds:CEA-861,DMT flags:has-cea861-vic] [dv.current:BT.656/1120 1920x1080p60 (2200x1125) stds:CEA-861,DMT flags:can-reduce-fps,CE-video,has-cea861-vic] -> "ipu1_csi0_mux":1 [] - entity 5: ipu1_vdic (3 pads, 3 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev2 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu1_csi0":1 [] <- "ipu1_csi1":1 [] pad1: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] pad2: Source [fmt:AYUV8_1X32/640x480@1/60 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prp":0 [] - entity 9: ipu2_vdic (3 pads, 3 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev3 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu2_csi0":1 [] <- "ipu2_csi1":1 [] pad1: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] pad2: Source [fmt:AYUV8_1X32/640x480@1/60 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prp":0 [] - entity 13: ipu1_ic_prp (3 pads, 5 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev4 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu1_vdic":2 [] <- "ipu1_csi0":1 [] <- "ipu1_csi1":1 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prpenc":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prpvf":0 [] - entity 17: ipu1_ic_prpenc (2 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev5 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu1_ic_prp":1 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prpenc capture":0 [] - entity 20: ipu1_ic_prpenc capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video0 pad0: Sink <- "ipu1_ic_prpenc":1 [] - entity 26: ipu1_ic_prpvf (2 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev6 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu1_ic_prp":2 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prpvf capture":0 [] - entity 29: ipu1_ic_prpvf capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video1 pad0: Sink <- "ipu1_ic_prpvf":1 [] - entity 35: ipu2_ic_prp (3 pads, 5 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev7 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu2_vdic":2 [] <- "ipu2_csi0":1 [] <- "ipu2_csi1":1 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prpenc":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prpvf":0 [] - entity 39: ipu2_ic_prpenc (2 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev8 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu2_ic_prp":1 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prpenc capture":0 [] - entity 42: ipu2_ic_prpenc capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video2 pad0: Sink <- "ipu2_ic_prpenc":1 [] - entity 48: ipu2_ic_prpvf (2 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev9 pad0: Sink [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] <- "ipu2_ic_prp":2 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prpvf capture":0 [] - entity 51: ipu2_ic_prpvf capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video3 pad0: Sink <- "ipu2_ic_prpvf":1 [] - entity 57: ipu1_csi0 (3 pads, 4 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev10 pad0: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480 compose.bounds:(0,0)/640x480 compose:(0,0)/640x480] <- "ipu1_csi0_mux":2 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prp":0 [] -> "ipu1_vdic":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_csi0 capture":0 [] - entity 61: ipu1_csi0 capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video4 pad0: Sink <- "ipu1_csi0":2 [] - entity 67: ipu1_csi1 (3 pads, 3 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev11 pad0: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480 compose.bounds:(0,0)/640x480 compose:(0,0)/640x480] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_ic_prp":0 [] -> "ipu1_vdic":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu1_csi1 capture":0 [] - entity 71: ipu1_csi1 capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video5 pad0: Sink <- "ipu1_csi1":2 [] - entity 77: ipu2_csi0 (3 pads, 3 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev12 pad0: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480 compose.bounds:(0,0)/640x480 compose:(0,0)/640x480] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prp":0 [] -> "ipu2_vdic":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_csi0 capture":0 [] - entity 81: ipu2_csi0 capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video6 pad0: Sink <- "ipu2_csi0":2 [] - entity 87: ipu2_csi1 (3 pads, 4 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev13 pad0: Sink [fmt:UYVY8_2X8/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range crop.bounds:(0,0)/640x480 crop:(0,0)/640x480 compose.bounds:(0,0)/640x480 compose:(0,0)/640x480] <- "ipu2_csi1_mux":2 [] pad1: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_ic_prp":0 [] -> "ipu2_vdic":0 [] pad2: Source [fmt:AYUV8_1X32/640x480@1/30 field:none colorspace:smpte170m xfer:709 ycbcr:601 quantization:lim-range] -> "ipu2_csi1 capture":0 [] - entity 91: ipu2_csi1 capture (1 pad, 1 link) type Node subtype V4L flags 0 device node name /dev/video7 pad0: Sink <- "ipu2_csi1":2 [] - entity 97: ipu1_csi0_mux (3 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev14 pad0: Sink [fmt:unknown/0x0] pad1: Sink [fmt:unknown/0x0] <- "tda19971 2-0048":0 [] pad2: Source [fmt:unknown/0x0] -> "ipu1_csi0":0 [] - entity 101: ipu2_csi1_mux (3 pads, 2 links) type V4L2 subdev subtype Unknown flags 0 device node name /dev/v4l-subdev15 pad0: Sink [fmt:unknown/0x0] pad1: Sink [fmt:unknown/0x0] <- "adv7180 2-0020":0 [] pad2: Source [fmt:unknown/0x0] -> "ipu2_csi1":0 [] v4l2-compliance test results: (on /dev/video6 as v4l2-compliance doesn't yet support subdevs) Driver Info: Driver name : imx-media-captu Card type : imx-media-capture Bus info : platform:ipu2_csi0 Driver version: 4.13.0 Capabilities : 0x84200001 Video Capture Streaming Extended Pix Format Device Capabilities Device Caps : 0x04200001 Video Capture Streaming Extended Pix Format Compliance test for device /dev/video6 (not using libv4l2): Required ioctls: test VIDIOC_QUERYCAP: OK Allow for multiple opens: test second video open: OK test VIDIOC_QUERYCAP: OK test VIDIOC_G/S_PRIORITY: OK Debug ioctls: test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) test VIDIOC_LOG_STATUS: OK (Not Supported) Input ioctls: test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) test VIDIOC_ENUMAUDIO: OK (Not Supported) fail: v4l2-test-input-output.cpp(418): G_INPUT not supported for a capture device test VIDIOC_G/S/ENUMINPUT: FAIL test VIDIOC_G/S_AUDIO: OK (Not Supported) Inputs: 0 Audio Inputs: 0 Tuners: 0 Output ioctls: test VIDIOC_G/S_MODULATOR: OK (Not Supported) test VIDIOC_G/S_FREQUENCY: OK (Not Supported) test VIDIOC_ENUMAUDOUT: OK (Not Supported) test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) test VIDIOC_G/S_AUDOUT: OK (Not Supported) Outputs: 0 Audio Outputs: 0 Modulators: 0 Input/Output configuration ioctls: test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) test VIDIOC_G/S_EDID: OK (Not Supported) Control ioctls: test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK test VIDIOC_QUERYCTRL: OK test VIDIOC_G/S_CTRL: OK fail: v4l2-test-controls.cpp(574): g_ext_ctrls does not support count == 0 test VIDIOC_G/S/TRY_EXT_CTRLS: FAIL test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK (Not Supported) test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) Standard Controls: 0 Private Controls: 0 Format ioctls: test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK test VIDIOC_G/S_PARM: OK test VIDIOC_G_FBUF: OK (Not Supported) test VIDIOC_G_FMT: OK test VIDIOC_TRY_FMT: OK test VIDIOC_S_FMT: OK test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) test Cropping: OK (Not Supported) test Composing: OK (Not Supported) test Scaling: OK (Not Supported) Codec ioctls: test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) test VIDIOC_G_ENC_INDEX: OK (Not Supported) test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported) Buffer ioctls: test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK test VIDIOC_EXPBUF: OK Test input 0: Total: 42, Succeeded: 40, Failed: 2, Warnings: 0 Tim Harvey (5): MAINTAINERS: add entry for NXP TDA1997x driver media: dt-bindings: Add bindings for TDA1997X media: i2c: Add TDA1997x HDMI receiver driver ARM: dts: imx: Add TDA19971 HDMI Receiver to GW54xx ARM: dts: imx: Add TDA19971 HDMI Receiver to GW551x .../devicetree/bindings/media/i2c/tda1997x.txt | 179 + MAINTAINERS | 8 + arch/arm/boot/dts/imx6q-gw54xx.dts | 102 + arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 29 +- arch/arm/boot/dts/imx6qdl-gw551x.dtsi | 85 + drivers/media/i2c/Kconfig | 9 + drivers/media/i2c/Makefile | 1 + drivers/media/i2c/tda1997x.c | 3516 ++++++++++++++++++++ include/dt-bindings/media/tda1997x.h | 78 + include/media/i2c/tda1997x.h | 53 + 10 files changed, 4057 insertions(+), 3 deletions(-) create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt create mode 100644 drivers/media/i2c/tda1997x.c create mode 100644 include/dt-bindings/media/tda1997x.h create mode 100644 include/media/i2c/tda1997x.h -- 2.7.4

4 11

[alsa-devel] [PATCH 0/6] ALSA: usb: UAC3. Add support for Basic Audio Device (BADD)
by Jorge Sanjuan 14 Dec '17

14 Dec '17

This adds functionality for the Basic Audio Device (BADD) subset that is defined in the USB Audio Class 3 (UAC3). The new class requires the device to have 3 usb configurations as follows: 1: Legacy Mode: UAC1 or UAC2. 2: BADD device with a prefined topology. (Minimum). 3: UAC3 device for more detailed description or more complex devices that can't be covered by the BADD profile. This patch series also includes some minor fixes to the usb card driver. Also, this has been implemented on top of the the patch which adds UAC3 support to the usb sound card driver: commit ddd452d7b04b86fb5f9285a19ac54deca9264ac1 Author: Ruslan Bilovol <ruslan.bilovol(a)gmail.com> Date: Tue Nov 7 04:01:20 2017 +0200 Jorge Sanjuan (6): ALSA: usb: ADC3: Add initial BADD spec support ALSA: usb: ADC3. BADD specification: fixed 48KHz sample rate. ALSA: usb: ADC3. Do not set sample rate for BADD configuration. usb: audio: Fix variable length field to be variable. ALSA: usb: Use Class Specific EP for UAC3 devices. ALSA: usb: Only get control header for UAC1 class. include/linux/usb/audio-v3.h | 2 +- sound/usb/Makefile | 3 +- sound/usb/badd.c | 495 +++++++++++++++++++++++++++++++++++++++++++ sound/usb/badd.h | 30 +++ sound/usb/card.c | 22 +- sound/usb/clock.c | 6 +- sound/usb/format.c | 7 +- sound/usb/stream.c | 175 +++++++++------ sound/usb/usbaudio.h | 1 + 9 files changed, 670 insertions(+), 71 deletions(-) create mode 100644 sound/usb/badd.c create mode 100644 sound/usb/badd.h -- 2.11.0

3 9

[alsa-devel] [PATCH v6 00/17] Add support for Cirrus Logic CS47L35/L85/L90/L91 codecs
by Richard Fitzgerald 13 Dec '17

13 Dec '17

The Cirrus Logic CS47L35, CS47L85, CS47L90/91 codecs are complex audio SoC devices. In addition to the core audio capability they have onboard GPIO, regulators, DSPs and interrupt controller and a large register map space accessed over SPI or I2C. This family of codecs is based around common IP blocks and they are managed by a set of common drivers referred to as "Madera". Patches still waiting for review/ack: #8 regulator #9 irqchip #14-17 ASoC Richard Fitzgerald (17): mfd: madera: Add register definitions for Cirrus Logic Madera codecs mfd: madera: Add DT bindings for Cirrus Logic Madera codecs mfd: madera: Add common support for Cirrus Logic Madera codecs mfd: madera: Register map tables for Cirrus Logic CS47L35 mfd: madera: Register map tables for Cirrus Logic CS47L85 mfd: madera: Register map tables for Cirrus Logic CS47L90/91 regulator: arizona-micsupp: Add support for Cirrus Logic Madera codecs regulator: arizona-ldo1: Add support for Cirrus Logic Madera codecs irqchip: Add driver for Cirrus Logic Madera codecs pinctrl: madera: Add DT bindings for Cirrus Logic Madera codecs pinctrl: madera: Add driver for Cirrus Logic Madera codecs gpio: madera: Support Cirrus Logic Madera class codecs ASoC: madera: Add DT bindings for Cirrus Logic Madera codecs ASoC: madera: Add common support for Cirrus Logic Madera codecs ASoC: cs47l35: Add codec driver for Cirrus Logic CS47L35 ASoC: cs47l85: Add codec driver for Cirrus Logic CS47L85 ASoC: cs47l90: Add codec driver for Cirrus Logic CS47L90 Documentation/devicetree/bindings/mfd/madera.txt | 102 + .../bindings/pinctrl/cirrus,madera-pinctrl.txt | 99 + .../bindings/regulator/arizona-regulator.txt | 3 +- Documentation/devicetree/bindings/sound/madera.txt | 67 + MAINTAINERS | 23 + drivers/gpio/Kconfig | 6 + drivers/gpio/Makefile | 1 + drivers/gpio/gpio-madera.c | 196 + drivers/irqchip/Kconfig | 3 + drivers/irqchip/Makefile | 1 + drivers/irqchip/irq-madera.c | 301 ++ drivers/mfd/Kconfig | 48 + drivers/mfd/Makefile | 13 + drivers/mfd/cs47l35-tables.c | 1610 +++++++ drivers/mfd/cs47l85-tables.c | 3010 +++++++++++++ drivers/mfd/cs47l90-tables.c | 2675 ++++++++++++ drivers/mfd/madera-core.c | 599 +++ drivers/mfd/madera-i2c.c | 140 + drivers/mfd/madera-spi.c | 139 + drivers/mfd/madera.h | 44 + drivers/pinctrl/Kconfig | 1 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/cirrus/Kconfig | 15 + drivers/pinctrl/cirrus/Makefile | 11 + drivers/pinctrl/cirrus/pinctrl-cs47l35.c | 46 + drivers/pinctrl/cirrus/pinctrl-cs47l85.c | 60 + drivers/pinctrl/cirrus/pinctrl-cs47l90.c | 58 + drivers/pinctrl/cirrus/pinctrl-madera.c | 1074 +++++ drivers/pinctrl/cirrus/pinctrl-madera.h | 40 + drivers/regulator/Kconfig | 15 +- drivers/regulator/arizona-ldo1.c | 82 +- drivers/regulator/arizona-micsupp.c | 71 +- include/dt-bindings/sound/madera.h | 27 + include/linux/irqchip/irq-madera-pdata.h | 23 + include/linux/irqchip/irq-madera.h | 98 + include/linux/mfd/madera/core.h | 196 + include/linux/mfd/madera/pdata.h | 61 + include/linux/mfd/madera/registers.h | 3987 ++++++++++++++++++ include/sound/madera-pdata.h | 61 + sound/soc/codecs/Kconfig | 23 + sound/soc/codecs/Makefile | 8 + sound/soc/codecs/cs47l35.c | 1748 ++++++++ sound/soc/codecs/cs47l85.c | 2722 ++++++++++++ sound/soc/codecs/cs47l90.c | 2661 ++++++++++++ sound/soc/codecs/madera.c | 4439 ++++++++++++++++++++ sound/soc/codecs/madera.h | 470 +++ 46 files changed, 27068 insertions(+), 10 deletions(-) create mode 100644 Documentation/devicetree/bindings/mfd/madera.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/cirrus,madera-pinctrl.txt create mode 100644 Documentation/devicetree/bindings/sound/madera.txt create mode 100644 drivers/gpio/gpio-madera.c create mode 100644 drivers/irqchip/irq-madera.c create mode 100644 drivers/mfd/cs47l35-tables.c create mode 100644 drivers/mfd/cs47l85-tables.c create mode 100644 drivers/mfd/cs47l90-tables.c create mode 100644 drivers/mfd/madera-core.c create mode 100644 drivers/mfd/madera-i2c.c create mode 100644 drivers/mfd/madera-spi.c create mode 100644 drivers/mfd/madera.h create mode 100644 drivers/pinctrl/cirrus/Kconfig create mode 100644 drivers/pinctrl/cirrus/Makefile create mode 100644 drivers/pinctrl/cirrus/pinctrl-cs47l35.c create mode 100644 drivers/pinctrl/cirrus/pinctrl-cs47l85.c create mode 100644 drivers/pinctrl/cirrus/pinctrl-cs47l90.c create mode 100644 drivers/pinctrl/cirrus/pinctrl-madera.c create mode 100644 drivers/pinctrl/cirrus/pinctrl-madera.h create mode 100644 include/dt-bindings/sound/madera.h create mode 100644 include/linux/irqchip/irq-madera-pdata.h create mode 100644 include/linux/irqchip/irq-madera.h create mode 100644 include/linux/mfd/madera/core.h create mode 100644 include/linux/mfd/madera/pdata.h create mode 100644 include/linux/mfd/madera/registers.h create mode 100644 include/sound/madera-pdata.h create mode 100644 sound/soc/codecs/cs47l35.c create mode 100644 sound/soc/codecs/cs47l85.c create mode 100644 sound/soc/codecs/cs47l90.c create mode 100644 sound/soc/codecs/madera.c create mode 100644 sound/soc/codecs/madera.h -- 2.11.0

3 28

[alsa-devel] [PATCH] ASoC: nuc900: Fix a loop timeout test
by Dan Carpenter 11 Dec '17

11 Dec '17

We should be finishing the loop with timeout set to zero but because this is a post-op we exit with timeout == -1. Fixes: 1082e2703a2d ("ASoC: NUC900/audio: add nuc900 audio driver support") Signed-off-by: Dan Carpenter <dan.carpenter(a)oracle.com> diff --git a/sound/soc/nuc900/nuc900-ac97.c b/sound/soc/nuc900/nuc900-ac97.c index b6615affe571..fde974d52bb2 100644 --- a/sound/soc/nuc900/nuc900-ac97.c +++ b/sound/soc/nuc900/nuc900-ac97.c @@ -67,7 +67,7 @@ static unsigned short nuc900_ac97_read(struct snd_ac97 *ac97, /* polling the AC_R_FINISH */ while (!(AUDIO_READ(nuc900_audio->mmio + ACTL_ACCON) & AC_R_FINISH) - && timeout--) + && --timeout) mdelay(1); if (!timeout) { @@ -121,7 +121,7 @@ static void nuc900_ac97_write(struct snd_ac97 *ac97, unsigned short reg, /* polling the AC_W_FINISH */ while ((AUDIO_READ(nuc900_audio->mmio + ACTL_ACCON) & AC_W_FINISH) - && timeout--) + && --timeout) mdelay(1); if (!timeout)

2 1

[alsa-devel] Cherry Trail + RT5645 devices with a mono speaker ?
by Hans de Goede 08 Dec '17

08 Dec '17

Hi Pierre-Louis, Bard, I've been looking into getting some Cherry Trail + RT5645 devices with a mono speaker I have to work properly. Specifically the goal is to mix the right channel into the left output, so that sounds which are only played over the right channel do not get lost. I'm using this UCM file: https://github.com/plbossart/UCM/blob/master/byt-rt5640/HiFi Looking at the rtl5640 UCM file, getting the mono speaker to work (in a first simple attempt) should be as simple as replacing: cset "name='SPOR MIX SPKVOL R Switch' on" With cset "name='SPOL MIX SPKVOL R Switch' on" But this does not work, the speaker test sound for the right speaker is still silent (works with headphones). I've also looked into directly poking the RT5645_SPO_MIXER i2c register for testing, but when checking its value with the original unmodified UCM file: [root@localhost ~]# i2cget -y -f 1 0x1a 0x48 w 0x06c8 That is: 0xc806 as the output of i2cget "w" mode needs byteswapping. Note that both the RT5645_M_SV_L_SPM_L and RT5645_M_SV_R_SPM_L bits are already cleared, which is weird as this is before I've modified anything. Also the RT5645_M_SV_R_SPM_R bit is cleared, but that is expected. Even if I manually set reg 0x48 to 0x07c8 which AFAIK should enable output of both left and right channels on the left speaker I still only get sounds played on the left channel. Any insights / help with this would be very much welcome. Regards, Hans

2 7

[alsa-devel] [PATCH v2 00/19] Add Headphone Detection to TLV320AIC31xx Driver
by Andrew F. Davis 07 Dec '17

07 Dec '17

Hello all, This series has the end goal of adding headphone detection to the tlv320aic31xx driver. The first few patches are mostly cleanups. Then a couple bug fixes I noticed. Followed by adding interrupt handling and finally headphone detection. This series (or at least patch #8) depend on this DT fix[0]. Thanks, Andrew Changes from v1: - Splitup the cleanup patch a bit more - Move the GPIO1 register fix patch before header cleanup so it can be taken back into stable - Added Acked-by - New patch dealing with regulator notifications - Various small touchups - Rebased on v4.15-rc1 + [0] [0] http://www.spinics.net/lists/kernel/msg2660968.html Andrew F. Davis (19): ASoC: tlv320aic31xx: File header and copyright cleanup ASoC: tlv320aic31xx: Change aic31xx_power_off return type to void ASoC: tlv320aic31xx: Move ACPI table next to OF table ASoC: tlv320aic31xx: General source formatting cleanup ASoC: tlv320aic31xx: Fix GPIO1 register definition ASoC: tlv320aic31xx: Reformat header file using GENMASK and BIT macros ASoC: tlv320aic31xx: Merge init function into probe ASoC: tlv320aic31xx: Switch GPIO handling to use gpiod_* API ASoC: tlv320aic31xx: Remove platform data ASoC: tlv320aic31xx: Add MICBIAS off setting ASoC: tlv320aic31xx: Check clock and divider before division ASoC: tlv320aic31xx: Add CODEC clock slave support ASoC: tlv320aic31xx: Fix inverted BCLK handling ASoC: tlv320aic31xx: Remove regulator notification handling ASoC: tlv320aic31xx: Reset registers during power up ASoC: tlv320aic31xx: Add short circuit detection support ASoC: tlv320aic31xx: Add overflow detection support ASoC: tlv320aic31xx: Add headphone/headset detection ASoC: tlv320aic31xx: Add button press detection .../devicetree/bindings/sound/tlv320aic31xx.txt | 1 + include/dt-bindings/sound/tlv320aic31xx-micbias.h | 1 + sound/soc/codecs/tlv320aic31xx.c | 422 ++++++++++-------- sound/soc/codecs/tlv320aic31xx.h | 496 ++++++++++----------- 4 files changed, 471 insertions(+), 449 deletions(-) rewrite sound/soc/codecs/tlv320aic31xx.h (83%) -- 2.15.0

2 62