November 2012 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] USB Quirks for Boss JS-8
by Keith A. Milner 15 Apr '13

15 Apr '13

Hi, I'm looking at developing a quirk for the Boss JS-8. The lsusb is as follows: Bus 001 Device 003: ID 0582:0109 Roland Corp. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 0 bDeviceProtocol 255 bMaxPacketSize0 64 idVendor 0x0582 Roland Corp. idProduct 0x0109 bcdDevice 0.01 iManufacturer 1 BOSS iProduct 2 JS-8 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 167 bNumInterfaces 3 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 2 bInterfaceProtocol 2 iInterface 0 ** UNRECOGNIZED: 06 24 f1 01 00 00 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 1 bNumEndpoints 1 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 2 bInterfaceProtocol 2 iInterface 0 ** UNRECOGNIZED: 07 24 01 01 00 01 00 ** UNRECOGNIZED: 0b 24 02 01 02 04 18 01 44 ac 00 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 5 Transfer Type Isochronous Synch Type Asynchronous Usage Type Data wMaxPacketSize 0x0070 1x 112 bytes bInterval 1 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 2 bInterfaceProtocol 1 iInterface 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 1 bNumEndpoints 1 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 2 bInterfaceProtocol 1 iInterface 0 ** UNRECOGNIZED: 07 24 01 07 00 01 00 ** UNRECOGNIZED: 0b 24 02 01 02 04 18 01 44 ac 00 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 37 Transfer Type Isochronous Synch Type Asynchronous Usage Type Implicit feedback Data wMaxPacketSize 0x0070 1x 112 bytes bInterval 1 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 3 bInterfaceProtocol 0 iInterface 0 ** UNRECOGNIZED: 06 24 f1 02 02 02 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 1 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 3 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 8 Mass Storage bDeviceSubClass 6 SCSI bDeviceProtocol 80 Bulk (Zip) bMaxPacketSize0 64 bNumConfigurations 0 Device Status: 0x0001 Self Powered I wasn't entirely sure about the quirk syntax as the two interfaces are at EP 4 and EP5. Does this mean I need to ignore the (non-existant) lower interfaces? Here's what I came up with: { /* Boss JS-8 Jam Station */ USB_DEVICE(0x0582, 0x0109), .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) { /* .vendor_name = "BOSS", */ /* .product_name = "JS-8", */ .ifnum = QUIRK_ANY_INTERFACE, .type = QUIRK_COMPOSITE, .data = (const struct snd_usb_audio_quirk[]) { { .ifnum = 0, .type = QUIRK_IGNORE_INTERFACE }, { .ifnum = 1, .type = QUIRK_IGNORE_INTERFACE }, { .ifnum = 2, .type = QUIRK_IGNORE_INTERFACE }, { .ifnum = 3, .type = QUIRK_IGNORE_INTERFACE }, { .ifnum = 4, .type = QUIRK_AUDIO_STANDARD_INTERFACE }, { .ifnum = 5, .type = QUIRK_AUDIO_STANDARD_INTERFACE }, { .ifnum = -1 } } } }, regards, -- Keith A. Milner

5 9

[alsa-devel] [RFC] Fix for conflict of HDMI and SPDIF IEC958 controls
by Takashi Iwai 12 Feb '13

12 Feb '13

Hi, there is a long-standing problem in HD-audio regarding IEC958 controls. When both an SPDIF and an HDMI are created on the same card (e.g. one from analog codec and one from graphics chip), the driver assigns the IEC958 controls just with new indices, 0, 1, 2... The problem is that there is no way to connect between this index and the actual PCM device. Currently, alsa-lib HDA-Intel.conf has a fixed configuration: spdif -> IEC958 xxx index=0, PCM dev=1 hdmi,0 -> IEC958 xxx index=0, PCM dev=3 hdmi,1 -> IEC958 xxx index=1, PCM dev=7 hdmi,2 -> IEC958 xxx index=2, PCM dev=8 hdmi,3 -> IEC958 xxx index=3, PCM dev=9 So obviously spdif and the first hdmi conflict. Basically this can be fixed by reassigning each IEC958 control with the same device number corresponding to the PCM device. That is, for SPDIF, assign a control element with device=1, for HDMI, device=3,7... However, this obviously breaks the old configuration unless user upgrades the alsa-lib configuration. Thus this is no-go. Now here is a compromise: the IEC958 control for SPDIF is reassigned to device=1 *only* when SPDIF and HDMI coexist. Since the configuration is anyway broken as is now in such a case, it's no big deal to fix one side in an incompatible way. (The reason why SPDIF is re-assigned is that I guess majority of user require more HDMI than SPDIF in such a configuration.) In addition, we need a fix in alsa-lib. Also not for breaking the compatibility with older kernel, we need some fallback check. I did a quick hack to alsa-lib conf code and added "skip_rest" option to the hook element, so that only the first matching element is taken. Long story short, I cooked up three patches. One patch is for kernel, to add the workaround above, and the two are for alsa-lib, one clean up and one to introduce the skip_rest option (and application to HDA-Intel.conf). My plan is to merge this to 3.8 tree, so it's no urgent issue. But it's of course always good to fix something. thanks, Takashi

5 29

[alsa-devel] hdsp rpm support
by Roman Haefeli 25 Jan '13

25 Jan '13

Hi everyone I would like to know current state of the RME HDSP RPM support. There was a thread [1] in 2008 on this list about the issue and things looked promising back then. However, I'm still unable to upload the firmware with alsa-driver from git on my Ubuntu 11.04 (32bit) machine with a 2.6.38 kernel. I posted a detailed description of the issue on the alsa-user list here [2]. Is it supposed to work with Cardbus? If not, is there something I can do to help support it? Any hints appreciated. Roman [1] http://mailman.alsa-project.org/pipermail/alsa-devel/2008-May/008128.html [2] http://article.gmane.org/gmane.linux.alsa.user/36022

5 12

[alsa-devel] question on snd_soc_dai_link_event
by Sebastien LEDUC 21 Jan '13

21 Jan '13

Hi, I have one question about current implementation of function snd_soc_dai_link_event Currently, on power up, it calls hw_params on the source and sink dai drivers, and digital_mute(0) on the sink dai driver I wonder why it does not call the full hw_params / prepare / trigger sequence on both dai drivers to start the 2 DAIs. Thanks in advance Regards, Sebastien

2 5

[alsa-devel] [PATCH v5 2/2] ASoC: mxs-saif: Remove platform data
by Fabio Estevam 08 Jan '13

08 Jan '13

From: Fabio Estevam <fabio.estevam(a)freescale.com> All MXS users have been converted to device tree and the board files have been removed. No need to keep platform data in the driver. Signed-off-by: Fabio Estevam <fabio.estevam(a)freescale.com> Acked-by: Dong Aisheng <dong.aisheng(a)linaro.org> Acked-by: Shawn Guo <shawn.guo(a)linaro.org> --- Changes since v4: - Rebased against fix/mxs branch and fix file removal Changes since v3: - Remove pdev->id check Changes since v2: - Also remove 'if (np)' as dt is the only probing mechanism. Changes since v1: - Also remove mxs_saif_platform_data and sound/saif.h, which was used only to include mxs_saif_platform_data definition. include/sound/saif.h | 16 ---------------- sound/soc/mxs/mxs-saif.c | 44 ++++++++++++++++---------------------------- 2 files changed, 16 insertions(+), 44 deletions(-) delete mode 100644 include/sound/saif.h diff --git a/include/sound/saif.h b/include/sound/saif.h deleted file mode 100644 index f22f3e1..0000000 --- a/include/sound/saif.h +++ /dev/null @@ -1,16 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#ifndef __SOUND_SAIF_H__ -#define __SOUND_SAIF_H__ - -struct mxs_saif_platform_data { - bool master_mode; /* if true use master mode */ - int master_id; /* id of the master if in slave mode */ -}; -#endif diff --git a/sound/soc/mxs/mxs-saif.c b/sound/soc/mxs/mxs-saif.c index c294fbb..05dbadb 100644 --- a/sound/soc/mxs/mxs-saif.c +++ b/sound/soc/mxs/mxs-saif.c @@ -32,7 +32,6 @@ #include <sound/pcm.h> #include <sound/pcm_params.h> #include <sound/soc.h> -#include <sound/saif.h> #include <asm/mach-types.h> #include <mach/hardware.h> #include <mach/mxs.h> @@ -660,43 +659,32 @@ static int __devinit mxs_saif_probe(struct platform_device *pdev) struct device_node *np = pdev->dev.of_node; struct resource *iores, *dmares; struct mxs_saif *saif; - struct mxs_saif_platform_data *pdata; struct pinctrl *pinctrl; int ret = 0; + struct device_node *master; - - if (!np && pdev->id >= ARRAY_SIZE(mxs_saif)) + if (!np) return -EINVAL; saif = devm_kzalloc(&pdev->dev, sizeof(*saif), GFP_KERNEL); if (!saif) return -ENOMEM; - if (np) { - struct device_node *master; - saif->id = of_alias_get_id(np, "saif"); - if (saif->id < 0) - return saif->id; - /* - * If there is no "fsl,saif-master" phandle, it's a saif - * master. Otherwise, it's a slave and its phandle points - * to the master. - */ - master = of_parse_phandle(np, "fsl,saif-master", 0); - if (!master) { - saif->master_id = saif->id; - } else { - saif->master_id = of_alias_get_id(master, "saif"); - if (saif->master_id < 0) - return saif->master_id; - } + saif->id = of_alias_get_id(np, "saif"); + if (saif->id < 0) + return saif->id; + /* + * If there is no "fsl,saif-master" phandle, it's a saif + * master. Otherwise, it's a slave and its phandle points + * to the master. + */ + master = of_parse_phandle(np, "fsl,saif-master", 0); + if (!master) { + saif->master_id = saif->id; } else { - saif->id = pdev->id; - pdata = pdev->dev.platform_data; - if (pdata && !pdata->master_mode) - saif->master_id = pdata->master_id; - else - saif->master_id = saif->id; + saif->master_id = of_alias_get_id(master, "saif"); + if (saif->master_id < 0) + return saif->master_id; } if (saif->master_id < 0 || saif->master_id >= ARRAY_SIZE(mxs_saif)) { -- 1.7.9.5

2 5

Re: [alsa-devel] Missing exactly 3 of 8 audio packets?
by Daniel Griscom 06 Jan '13

06 Jan '13

Dear Daniel (M) and Clemens, I'd like to conclude this thread if I could. It seems clear that configuring our USB audio card's descriptor with a bInterval value of 1 (a packet every microframe) was too aggressive, and was part of what caused the packet stuttering issue. (Right?) We almost certainly should increase bInterval; I'll try 2, and if that seems stable will probably go to 3 (4 microframes) for some margin. However, I'm still concerned that the symptoms don't sound like a simple starvation issue, where I'd expect to have a missing frame every once in a while. Instead, we were seeing reliable operation interspersed with periods where lots of packets were being consistently omitted. To me, this suggests that there's some other issue going on, either in the USB stack or in the USB hardware itself. Given that, I'm worried that increasing bInterval will just move the symptoms around, making it harder to duplicate but not truly becoming robust. Any thoughts on this? Should I try chasing the issue into the Linux USB development mailing list, or will they just say "set bInterval to a larger value!"? Thanks, Dan -- Daniel T. Griscom griscom(a)suitable.com Suitable Systems http://www.suitable.com/ 1 Centre Street, Suite 204 (781) 665-0053 Wakefield, MA 01880-2400

2 1

[alsa-devel] [PATCH] ALSA: usb-audio: Add quirk for Focusrite Scarlett 18i6
by Martin Schwenke 29 Dec '12

29 Dec '12

Probing this device currently fails in snd_usb_audio_probe() because the call to snd_usb_create_mixer() fails. This is due to unknown or non-standard interface descriptor subtypes in parse_audio_unit(): usbaudio: unit 51: unexpected type 0x09 snd-usb-audio: probe of 1-8:1.0 failed with error -5 Some people are working around this by recompiling usb-audio with the call to snd_usb_create_mixer() commented out. It would be nice to avoid that. While the best idea would be to look into the mixer creation failure, a reasonable short-term solution is to use quirks to only probe the trouble-free interfaces. This allows audio and MIDI interfaces to be used without any obvious issues. Interface 0 is the main one to ignore. It contains lots of control-fu, including the unexpected interface descriptor subtypes. Interface 5 is for firmware updates and I'm not sure how to get support for this. Interface 3 is some sort of control interface that I don't understand: Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 1 Audio bInterfaceSubClass 1 Control Device bInterfaceProtocol 0 iInterface 0 AudioControl Interface Descriptor: bLength 9 bDescriptorType 36 bDescriptorSubtype 1 (HEADER) bcdADC 1.00 wTotalLength 9 bInCollection 1 baInterfaceNr( 0) 1 Signed-off-by: Martin Schwenke <martin(a)meltin.net> --- sound/usb/quirks-table.h | 52 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/sound/usb/quirks-table.h b/sound/usb/quirks-table.h index 88d8ceb..c9dde5f 100644 --- a/sound/usb/quirks-table.h +++ b/sound/usb/quirks-table.h @@ -2882,6 +2882,58 @@ YAMAHA_DEVICE(0x7010, "UB99"), { /* + * Focusrite Scarlett 18i6 + * + * Avoid mixer creation, which otherwise fails because some of + * the interface descriptor subtypes for interface 0 are + * unknown. That should be fixed or worked-around but this at + * least allows the device to be used successfully with a DAW + * and an external mixer. See comments below about other + * ignored interfaces. + */ + USB_DEVICE(0x1235, 0x8004), + .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) { + .vendor_name = "Focusrite", + .product_name = "Scarlett 18i6", + .ifnum = QUIRK_ANY_INTERFACE, + .type = QUIRK_COMPOSITE, + .data = & (const struct snd_usb_audio_quirk[]) { + { + /* InterfaceSubClass 1 (Control Device) */ + .ifnum = 0, + .type = QUIRK_IGNORE_INTERFACE + }, + { + .ifnum = 1, + .type = QUIRK_AUDIO_STANDARD_INTERFACE + }, + { + .ifnum = 2, + .type = QUIRK_AUDIO_STANDARD_INTERFACE + }, + { + /* InterfaceSubClass 1 (Control Device) */ + .ifnum = 3, + .type = QUIRK_IGNORE_INTERFACE + }, + { + .ifnum = 4, + .type = QUIRK_MIDI_STANDARD_INTERFACE + }, + { + /* InterfaceSubClass 1 (Device Firmware Update) */ + .ifnum = 5, + .type = QUIRK_IGNORE_INTERFACE + }, + { + .ifnum = -1 + } + } + } +}, + +{ + /* * Some USB MIDI devices don't have an audio control interface, * so we have to grab MIDI streaming interfaces here. */ -- 1.7.10.4

4 5

[alsa-devel] EMU-1212m "no Audiodock - no firmware" patch
by oeai 29 Dec '12

29 Dec '12

Aloha! i've been posting about my problem earlier, but i decided to DIY the problem was that when going up from suspend the firmware for additional card (that i don't have) was trying to load, -but there's no card - sorry, i'm gonna check few more thousand times that caused my cpu to load insanely so in the patch i've changed few more strings for debugging but actually the one (but not the only) bug is here *** 728,739 **** ! if (reg & EMU_HANA_OPTION_DOCK_OFFLINE) { --- 729,740 ---- ! if (reg & !EMU_HANA_OPTION_DOCK_OFFLINE) { the thing is in the "!"EMU_HANA_OPTION_DOCK_OFFLINE -> then the firmware should be loaded. and to debug some errors if something i've put the one more else state so if no audiodock - it could continue to load config *** 777,784 **** /* Unmute all. Default is muted after a firmware load */ snd_emu1010_fpga_write(emu, EMU_HANA_UNMUTE, EMU_UNMUTE); } } ! snd_printk(KERN_INFO "emu1010: firmware thread stopping\n"); return 0; } --- 778,790 ---- /* Unmute all. Default is muted after a firmware load */ snd_emu1010_fpga_write(emu, EMU_HANA_UNMUTE, EMU_UNMUTE); } + else if ((reg & 0x3f) == 0x15) + { + snd_printk(KERN_INFO "emu1212m: trying to load config emu_hana_fpga_config"); + snd_emu1010_fpga_write(emu, EMU_HANA_FPGA_CONFIG,0x02); + } } ! snd_printk(KERN_INFO "emu1010: emu dock firmware thread stopping\n"); return 0; } *************** then i've commented the power_down for audiodock - it should be in other place, but as i'm 1212m user - it works for me - you know. *** 841,847 **** outl(0x0005a000, emu->port + HCFG); /* Disable 48Volt power to Audio Dock */ ! snd_emu1010_fpga_write(emu, EMU_HANA_DOCK_PWR, 0); /* ID, should read & 0x7f = 0x55. (Bit 7 is the IRQ bit) */ snd_emu1010_fpga_read(emu, EMU_HANA_ID, &reg); --- 847,853 ---- outl(0x0005a000, emu->port + HCFG); /* Disable 48Volt power to Audio Dock */ ! /*snd_emu1010_fpga_write(emu, EMU_HANA_DOCK_PWR, 0);*/ /* ID, should read & 0x7f = 0x55. (Bit 7 is the IRQ bit) */ snd_emu1010_fpga_read(emu, EMU_HANA_ID, &reg); *************** and here i've changed that the emu_model was firstly enabled and then ecard - since i don't know what's the ecard i thought that it is a second module of my emu card. *** 2079,2088 **** { if (emu->card_capabilities->ca_cardbus_chip) snd_emu10k1_cardbus_init(emu); ! if (emu->card_capabilities->ecard) ! snd_emu10k1_ecard_init(emu); ! else if (emu->card_capabilities->emu_model) snd_emu10k1_emu1010_init(emu); else snd_emu10k1_ptr_write(emu, AC97SLOT, 0, AC97SLOT_CNTR|AC97SLOT_LFE); snd_emu10k1_init(emu, emu->enable_ir, 1); --- 2098,2111 ---- { if (emu->card_capabilities->ca_cardbus_chip) snd_emu10k1_cardbus_init(emu); ! ! if (emu->card_capabilities->emu_model) ! { snd_emu10k1_emu1010_init(emu); + + } + else if (emu->card_capabilities->ecard) + snd_emu10k1_ecard_init(emu); else snd_emu10k1_ptr_write(emu, AC97SLOT, 0, AC97SLOT_CNTR|AC97SLOT_LFE); snd_emu10k1_init(emu, emu->enable_ir, 1); Now i still have the problem of waking up i cannot request_firmware() properly on resume and it is trying to load nothing and other changes in patch - that was trying to debug the situation so i can at least alsa-reload at anytime. also i'd like to ask if i can use the ctxfi modules - CA0110-IBG i got xfi card (it is second of 5) that actually uses as i believe the same logic - maybe a lil modified, but not so much imho. -- RA OEAI

3 8

[alsa-devel] sound: usb-audio: full capture/playback/spdif support for Digidesign Mbox 2
by Damien Zammit 23 Dec '12

23 Dec '12

Hi folks, I have put together full support for Digidesign Mbox 2, but it needs someone to help me merge it into alsa. I haven't seen the latest snd-usb-audio code since last year, it seems to have branched into multiple files. I have worked out how the Digidesign Mbox 2 needs to be configured, it supports SPDIF i/o simultaneously with analogue but can be toggled on and off by using different altsettings. Also the sample clock rate must be configured via a special method. Therefore I have provided for this in a device_setup parameter with 4 settings: 48Khz Spdif+analog = 0 44.1Khz Spdif+analog = 1 48Khz Analog only = 2 44.1Khz Analog only = 3 ###### audio /* Digidesign Mbox 2 workaround: * supports S24_3BE BIG ENDIAN in an unusual way */ if (chip->usb_id == USB_ID(0x0dba, 0x3000)) pcm_format = SNDRV_PCM_FORMAT_S24_3BE; static int mbox2_skip_setting_quirk(struct snd_usb_audio *chip, int iface, int altno); static int parse_audio_endpoints(struct snd_usb_audio *chip, int iface_no) { ..... ..... /* Digidesign Mbox 2: skip altsets incompatible with device_setup */ if (chip->usb_id == USB_ID(0x0dba, 0x3000) && mbox2_skip_setting_quirk(chip, iface_no, altno)) continue; ..... } #define MBOX2_SET_48K_SPDIF 0 #define MBOX2_SET_44K_SPDIF 1 #define MBOX2_SET_48K_ANALOG 2 #define MBOX2_SET_44K_ANALOG 3 static int mbox2_skip_setting_quirk(struct snd_usb_audio *chip, int iface, int altno) { u8 srate[3]; /* Reset ifaces 2-5 to 0 altsetting. */ usb_set_interface(chip->dev, iface, 0); if (device_setup[chip->index] == MBOX2_SET_48K_SPDIF || device_setup[chip->index] == MBOX2_SET_48K_ANALOG) { //setup 48k srate[0]=0x80; srate[1]=0xbb; srate[2]=0x00; /* Send the magic! */ snd_usb_ctl_msg(chip->dev, usb_sndctrlpipe(chip->dev, 0), 0x01, 0x22, 0x0100, 0x0085, &srate, 0x0003, 1000); snd_usb_ctl_msg(chip->dev, usb_sndctrlpipe(chip->dev, 0), 0x81, 0xa2, 0x0100, 0x0085, &srate, 0x0003, 1000); snd_usb_ctl_msg(chip->dev, usb_sndctrlpipe(chip->dev, 0), 0x81, 0xa2, 0x0100, 0x0086, &srate, 0x0003, 1000); snd_usb_ctl_msg(chip->dev, usb_sndctrlpipe(chip->dev, 0), 0x81, 0xa2, 0x0100, 0x0003, &srate, 0x0003, 1000); snd_printk(KERN_INFO "Digidesign Mbox 2: 24 Bit 48000Hz"); if (device_setup[chip->index] == MBOX2_SET_48K_SPDIF) { //setup spdif snd_printk(KERN_INFO ", SPDIF\n"); if (altno != 2) return 1; } else { //setup analog snd_printk(KERN_INFO ", ANALOGUE\n"); if (altno != 3) return 1; } } else { //setup 44k srate[0]=0x44; srate[1]=0xac; srate[2]=0x00; /* Send the magic! */ snd_usb_ctl_msg(chip->dev, usb_sndctrlpipe(chip->dev, 0), 0x01, 0x22, 0x0100, 0x0085, &srate, 0x0003, 1000); snd_usb_ctl_msg(chip->dev, usb_sndctrlpipe(chip->dev, 0), 0x81, 0xa2, 0x0100, 0x0085, &srate, 0x0003, 1000); snd_usb_ctl_msg(chip->dev, usb_sndctrlpipe(chip->dev, 0), 0x81, 0xa2, 0x0100, 0x0086, &srate, 0x0003, 1000); snd_usb_ctl_msg(chip->dev, usb_sndctrlpipe(chip->dev, 0), 0x81, 0xa2, 0x0100, 0x0003, &srate, 0x0003, 1000); snd_printk(KERN_INFO "Digidesign Mbox 2: 24 Bit 44100Hz"); if (device_setup[chip->index] == MBOX2_SET_44K_SPDIF || device_setup[chip->index] == MBOX2_SET_44K_ANALOG) { //setup spdif snd_printk(KERN_INFO ", SPDIF\n"); if (altno != 2) return 1; } else { //setup analog snd_printk(KERN_INFO ", ANALOGUE\n"); if (altno != 3) return 1; } } return 0; } #define MBOX2_FIRMWARE_SIZE 646 #define MBOX2_BOOT_LOADING 0x01 /* Hard coded into the device */ #define MBOX2_BOOT_READY 0x02 /* Hard coded into the device */ static int snd_usb_mbox2_boot_quirk(struct usb_device *dev) { struct usb_host_config *config = dev->actconfig; int err; u8 enablemagic[3]; u8 bootresponse; int fwsize; if ((fwsize = le16_to_cpu(get_cfg_desc(config)->wTotalLength)) == MBOX2_FIRMWARE_SIZE) { snd_printdd("Sending Digidesign Mbox 2 boot sequence...\n"); /* From USB Snoop, * * SetupPacket = RT RQ VHVL INDX SIZE * RT = 0xRT Request Type * RQ = 0xRQ Request * VHVL = 0xVLVH Value in reverse byte order * INDX = 0xDXIN Index in reverse byte order * SIZE = 0xZESI Size in reverse byte order * * Magic boot code setup packet: c0 85 01 00 00 00 12 00 * RQ RT VLVH DXIN ZESI * becomes 0x85, 0xc0, 0x0001, 0x0000, &RETURNDATA, 0x0012, TIMEOUT * for snd_usb_ctl_msg() */ mbox2_reboot: snd_usb_ctl_msg(dev, usb_rcvctrlpipe(dev, 0), 0x85, 0xc0, 0x0001, 0x0000, &bootresponse, 0x0012, 1000); if (bootresponse == MBOX2_BOOT_LOADING) { snd_printdd("device not ready, resending boot sequence...\n"); goto mbox2_reboot; } if (bootresponse == MBOX2_BOOT_READY) { snd_printdd("device initialised!\n"); err = usb_get_descriptor(dev, USB_DT_DEVICE, 0, &dev->descriptor, sizeof(dev->descriptor)); config = dev->actconfig; if (err < 0) snd_printdd("error usb_get_descriptor: %d\n", err); err = usb_reset_configuration(dev); if (err < 0) snd_printdd("error usb_reset_configuration: %d\n", err); snd_printdd("mbox2_boot: new boot length = %d\n", le16_to_cpu(get_cfg_desc(config)->wTotalLength)); /* Successful boot, (should reset all altsettings to 0 like windows does, but works without it) * but now we will try sending capture/playback enable magic * * 80 bb 00 = 24bit mode - S24_3BE * 44 ac 00 = 16bit mode? * */ /* We want 48khz mode for now */ enablemagic[0]=0x80; enablemagic[1]=0xbb; enablemagic[2]=0x00; /* Send the magic! */ snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0x01, 0x22, 0x0100, 0x0085, &enablemagic, 0x0003, 1000); snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0x81, 0xa2, 0x0100, 0x0085, &enablemagic, 0x0003, 1000); snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0x81, 0xa2, 0x0100, 0x0086, &enablemagic, 0x0003, 1000); snd_usb_ctl_msg(dev, usb_sndctrlpipe(dev, 0), 0x81, 0xa2, 0x0100, 0x0003, &enablemagic, 0x0003, 1000); return 0; /* Succesful boot */ } snd_printdd("unknown bootresponse, ignoring device: %d\n",bootresponse); return -ENODEV; } snd_printk("Invalid firmware size: %d\n",fwsize); return -ENODEV; } ####### quirk: { USB_DEVICE(0x0dba, 0x3000), .driver_info = (unsigned long) & (const struct snd_usb_audio_quirk) { .vendor_name = "Digidesign", .product_name = "Mbox 2", .ifnum = QUIRK_ANY_INTERFACE, .type = QUIRK_COMPOSITE, .data = (const struct snd_usb_audio_quirk[]) { { .ifnum = 0, .type = QUIRK_IGNORE_INTERFACE }, { .ifnum = 1, .type = QUIRK_AUDIO_STANDARD_INTERFACE }, { .ifnum = 2, .type = QUIRK_AUDIO_STANDARD_INTERFACE }, { .ifnum = 3, .type = QUIRK_AUDIO_STANDARD_INTERFACE }, { .ifnum = 4, .type = QUIRK_AUDIO_STANDARD_INTERFACE }, { .ifnum = 5, .type = QUIRK_AUDIO_STANDARD_INTERFACE }, { .ifnum = 6, .type = QUIRK_MIDI_MBOX2, .data = & (const struct snd_usb_midi_endpoint_info) { .out_ep = 0x02, .out_cables = 0x0001, .in_ep = 0x81, .in_interval = 0x01, .in_cables = 0x0001 } }, { .ifnum = -1 } } } }, ##### midi case QUIRK_MIDI_MBOX2: /* Digidesign Mbox 2 uses MIDIMAN MIDI protocol */ umidi->usb_protocol_ops = &snd_usbmidi_midiman_ops; /* * We have to make sure that the USB core looks * again at interface 6 by calling usb_set_interface() on it. */ usb_set_interface(umidi->chip->dev, 6, 0); memcpy(&endpoints[0], quirk->data, sizeof(struct snd_usb_midi_endpoint_info)); err = 0; break; Damien

4 26

[alsa-devel] [Resend PATCH v6 1/4] pinctrl: atmel-ssc: add pinctrl support
by Bo Shen 13 Dec '12

13 Dec '12

Add pinctrl support for atmel ssc peripheral Signed-off-by: Bo Shen <voice.shen(a)atmel.com> --- Resend - based on linux-next-20121115 - commit id: 3805711eb31d3b980c4a55a6994bbc8b22a9ec65 Change since v5 - correct the pull setting, without pull up Change since v4 - This is initial version --- arch/arm/boot/dts/at91sam9260.dtsi | 18 ++++++++++++++++++ arch/arm/boot/dts/at91sam9263.dtsi | 36 ++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/at91sam9g45.dtsi | 36 ++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/at91sam9n12.dtsi | 26 ++++++++++++++++++++++++++ arch/arm/boot/dts/at91sam9x5.dtsi | 32 +++++++++++++++++++++++++------- drivers/misc/atmel-ssc.c | 8 ++++++++ 6 files changed, 149 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi index 3164dcd..f9dc7db 100644 --- a/arch/arm/boot/dts/at91sam9260.dtsi +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -217,6 +217,22 @@ }; }; + ssc0 { + pinctrl_ssc0_tx: ssc0_tx-0 { + atmel,pins = + <1 16 0x1 0x0 /* PB16 periph A */ + 1 17 0x1 0x0 /* PB17 periph A */ + 1 18 0x1 0x0>; /* PB18 periph A */ + }; + + pinctrl_ssc0_rx: ssc0_rx-0 { + atmel,pins = + <1 19 0x1 0x0 /* PB19 periph A */ + 1 20 0x1 0x0 /* PB20 periph A */ + 1 21 0x1 0x0>; /* PB21 periph A */ + }; + }; + pioA: gpio@fffff400 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x200>; @@ -350,6 +366,8 @@ compatible = "atmel,at91rm9200-ssc"; reg = <0xfffbc000 0x4000>; interrupts = <14 4 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; status = "disable"; }; diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi index 96e0bc9..6e9a4ff 100644 --- a/arch/arm/boot/dts/at91sam9263.dtsi +++ b/arch/arm/boot/dts/at91sam9263.dtsi @@ -165,6 +165,38 @@ }; }; + ssc0 { + pinctrl_ssc0_tx: ssc0_tx-0 { + atmel,pins = + <1 0 0x2 0x0 /* PB0 periph B */ + 1 1 0x2 0x0 /* PB1 periph B */ + 1 2 0x2 0x0>; /* PB2 periph B */ + }; + + pinctrl_ssc0_rx: ssc0_rx-0 { + atmel,pins = + <1 3 0x2 0x0 /* PB3 periph B */ + 1 4 0x2 0x0 /* PB4 periph B */ + 1 5 0x2 0x0>; /* PB5 periph B */ + }; + }; + + ssc1 { + pinctrl_ssc1_tx: ssc1_tx-0 { + atmel,pins = + <1 6 0x1 0x0 /* PB6 periph A */ + 1 7 0x1 0x0 /* PB7 periph A */ + 1 8 0x1 0x0>; /* PB8 periph A */ + }; + + pinctrl_ssc1_rx: ssc1_rx-0 { + atmel,pins = + <1 9 0x1 0x0 /* PB9 periph A */ + 1 10 0x1 0x0 /* PB10 periph A */ + 1 11 0x1 0x0>; /* PB11 periph A */ + }; + }; + pioA: gpio@fffff200 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff200 0x200>; @@ -262,6 +294,8 @@ compatible = "atmel,at91rm9200-ssc"; reg = <0xfff98000 0x4000>; interrupts = <16 4 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; status = "disable"; }; @@ -269,6 +303,8 @@ compatible = "atmel,at91rm9200-ssc"; reg = <0xfff9c000 0x4000>; interrupts = <17 4 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; status = "disable"; }; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index c40c3eb..63cf206 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -198,6 +198,38 @@ }; }; + ssc0 { + pinctrl_ssc0_tx: ssc0_tx-0 { + atmel,pins = + <3 0 0x1 0x0 /* PD0 periph A */ + 3 1 0x1 0x0 /* PD1 periph A */ + 3 2 0x1 0x0>; /* PD2 periph A */ + }; + + pinctrl_ssc0_rx: ssc0_rx-0 { + atmel,pins = + <3 3 0x1 0x0 /* PD3 periph A */ + 3 4 0x1 0x0 /* PD4 periph A */ + 3 5 0x1 0x0>; /* PD5 periph A */ + }; + }; + + ssc1 { + pinctrl_ssc1_tx: ssc1_tx-0 { + atmel,pins = + <3 10 0x1 0x0 /* PD10 periph A */ + 3 11 0x1 0x0 /* PD11 periph A */ + 3 12 0x1 0x0>; /* PD12 periph A */ + }; + + pinctrl_ssc1_rx: ssc1_rx-0 { + atmel,pins = + <3 13 0x1 0x0 /* PD13 periph A */ + 3 14 0x1 0x0 /* PD14 periph A */ + 3 15 0x1 0x0>; /* PD15 periph A */ + }; + }; + pioA: gpio@fffff200 { compatible = "atmel,at91rm9200-gpio"; reg = <0xfffff200 0x200>; @@ -331,6 +363,8 @@ compatible = "atmel,at91sam9g45-ssc"; reg = <0xfff9c000 0x4000>; interrupts = <16 4 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; status = "disable"; }; @@ -338,6 +372,8 @@ compatible = "atmel,at91sam9g45-ssc"; reg = <0xfffa0000 0x4000>; interrupts = <17 4 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>; status = "disable"; }; diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index 7b644c5..b211da6 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -28,6 +28,7 @@ tcb1 = &tcb1; i2c0 = &i2c0; i2c1 = &i2c1; + ssc0 = &ssc0; }; cpus { cpu@0 { @@ -199,6 +200,22 @@ }; }; + ssc0 { + pinctrl_ssc0_tx: ssc0_tx-0 { + atmel,pins = + <0 24 0x2 0x0 /* PA24 periph B */ + 0 25 0x2 0x0 /* PA25 periph B */ + 0 26 0x2 0x0>; /* PA26 periph B */ + }; + + pinctrl_ssc0_rx: ssc0_rx-0 { + atmel,pins = + <0 27 0x2 0x0 /* PA27 periph B */ + 0 28 0x2 0x0 /* PA28 periph B */ + 0 29 0x2 0x0>; /* PA29 periph B */ + }; + }; + pioA: gpio@fffff400 { compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x200>; @@ -249,6 +266,15 @@ status = "disabled"; }; + ssc0: ssc@f0010000 { + compatible = "atmel,at91sam9g45-ssc"; + reg = <0xf0010000 0x4000>; + interrupts = <28 4 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; + status = "disable"; + }; + usart0: serial@f801c000 { compatible = "atmel,at91sam9260-usart"; reg = <0xf801c000 0x4000>; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index 1cb26c28..df84f39 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -88,13 +88,6 @@ interrupts = <1 4 7>; }; - ssc0: ssc@f0010000 { - compatible = "atmel,at91sam9g45-ssc"; - reg = <0xf0010000 0x4000>; - interrupts = <28 4 5>; - status = "disable"; - }; - tcb0: timer@f8008000 { compatible = "atmel,at91sam9x5-tcb"; reg = <0xf8008000 0x100>; @@ -214,6 +207,22 @@ }; }; + ssc0 { + pinctrl_ssc0_tx: ssc0_tx-0 { + atmel,pins = + <0 24 0x2 0x0 /* PA24 periph B */ + 0 25 0x2 0x0 /* PA25 periph B */ + 0 26 0x2 0x0>; /* PA26 periph B */ + }; + + pinctrl_ssc0_rx: ssc0_rx-0 { + atmel,pins = + <0 27 0x2 0x0 /* PA27 periph B */ + 0 28 0x2 0x0 /* PA28 periph B */ + 0 29 0x2 0x0>; /* PA29 periph B */ + }; + }; + pioA: gpio@fffff400 { compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio"; reg = <0xfffff400 0x200>; @@ -266,6 +275,15 @@ status = "disabled"; }; + ssc0: ssc@f0010000 { + compatible = "atmel,at91sam9g45-ssc"; + reg = <0xf0010000 0x4000>; + interrupts = <28 4 5>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>; + status = "disable"; + }; + usart0: serial@f801c000 { compatible = "atmel,at91sam9260-usart"; reg = <0xf801c000 0x200>; diff --git a/drivers/misc/atmel-ssc.c b/drivers/misc/atmel-ssc.c index a769719..3b3d0e0 100644 --- a/drivers/misc/atmel-ssc.c +++ b/drivers/misc/atmel-ssc.c @@ -19,6 +19,7 @@ #include <linux/module.h> #include <linux/of.h> +#include <linux/pinctrl/consumer.h> /* Serialize access to ssc_list and user count */ static DEFINE_SPINLOCK(user_lock); @@ -131,6 +132,13 @@ static int ssc_probe(struct platform_device *pdev) struct resource *regs; struct ssc_device *ssc; const struct atmel_ssc_platform_data *plat_dat; + struct pinctrl *pinctrl; + + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (IS_ERR(pinctrl)) { + dev_err(&pdev->dev, "Failed to request pinctrl\n"); + return PTR_ERR(pinctrl); + } ssc = devm_kzalloc(&pdev->dev, sizeof(struct ssc_device), GFP_KERNEL); if (!ssc) { -- 1.7.9.5

2 3