April 2007 - Alsa-devel - mailman.alsa-project.org

[alsa-devel] [PATCHv2] ALSA: Support Media Vision Jazz16 chips
by Rask Ingemann Lambertsen 20 Apr '07

20 Apr '07

From: Rask Ingemann Lambertsen <rask(a)sygehus.dk> - Add support for Jazz16 features to the common SoundBlaster code. - Add a front end for Jazz16 based sound cards. Tested with a Jazz16 based sound card and Linux 2.6.20.6. Signed-off-by: Rask Ingemann Lambertsen <rask(a)sygehus.dk> --- This patch is a prerequisite for the Jazz PnP patch, which needs the patched include/sound/sb.h. Documentation/sound/alsa/ALSA-Configuration.txt | 10 include/sound/sb.h | 5 sound/isa/Kconfig | 15 + sound/isa/sb/Makefile | 2 sound/isa/sb/jazz16.c | 183 ++++++++++++++ sound/isa/sb/sb8_main.c | 98 +++++++ sound/isa/sb/sb_common.c | 12 sound/isa/sb/sb_mixer.c | 3 8 files changed, 323 insertions(+), 5 deletions(-) Changes since the last patch: The same DMA channel is now used for both 8-bit and 16-bit sound. DSP high-speed mode isn't used at all now for the Jazz16. A 16-bit DMA buffer can now be 128 kB instead of 64 kB. diff -rup linux-2.6.20.6-clean/Documentation/sound/alsa/ALSA-Configuration.txt linux-2.6.20.6-ril/Documentation/sound/alsa/ALSA-Configuration.txt --- linux-2.6.20.6-clean/Documentation/sound/alsa/ALSA-Configuration.txt 2007-02-04 19:44:54.000000000 +0100 +++ linux-2.6.20.6-ril/Documentation/sound/alsa/ALSA-Configuration.txt 2007-04-07 17:31:38.000000000 +0200 @@ -1120,6 +1120,16 @@ Prior to version 0.9.0rc4 options had a This module supports multiple cards, autoprobe and ISA PnP. + Module snd-jazz16 + ----------------- + + Module for sound cards based on Media Vision Jazz16 chip (PnP only) + + This module supports multiple cards and PnP. + + Note: You will most likely want to enable Jazz16 PnP support + (CONFIG_JAZZ16PNP) in the kernel. + Module snd-korg1212 ------------------- diff -rup linux-2.6.20.6-clean/include/sound/sb.h linux-2.6.20.6-ril/include/sound/sb.h --- linux-2.6.20.6-clean/include/sound/sb.h 2007-02-04 19:44:54.000000000 +0100 +++ linux-2.6.20.6-ril/include/sound/sb.h 2007-04-07 17:31:38.000000000 +0200 @@ -33,6 +33,7 @@ enum sb_hw_type { SB_HW_20, SB_HW_201, SB_HW_PRO, + SB_HW_JAZZ16, /* Media Vision Jazz16 chip */ SB_HW_16, SB_HW_16CSP, /* SB16 with CSP chip */ SB_HW_ALS100, /* Avance Logic ALS100 chip */ @@ -142,6 +143,7 @@ struct snd_sb { #define SB_DSP_HI_INPUT_AUTO 0x98 #define SB_DSP_IMMED_INT 0xf2 #define SB_DSP_GET_VERSION 0xe1 +#define SB_DSP_GET_JAZZ_VERSION 0xfa #define SB_DSP_SPEAKER_ON 0xd1 #define SB_DSP_SPEAKER_OFF 0xd3 #define SB_DSP_DMA8_OFF 0xd0 @@ -265,6 +267,9 @@ struct snd_sb { #define SB_DMASETUP_DMA6 0x40 #define SB_DMASETUP_DMA7 0x80 +/* Check the output of SB_DSP_GET_JAZZ_VERSION. */ +#define SB_VERSION_IS_JAZZ16(x) ((x) == 0x12) + /* * */ diff -rup linux-2.6.20.6-clean/sound/isa/Kconfig linux-2.6.20.6-ril/sound/isa/Kconfig --- linux-2.6.20.6-clean/sound/isa/Kconfig 2007-02-04 19:44:54.000000000 +0100 +++ linux-2.6.20.6-ril/sound/isa/Kconfig 2007-04-07 17:31:38.000000000 +0200 @@ -248,6 +248,21 @@ config SND_INTERWAVE_STB To compile this driver as a module, choose M here: the module will be called snd-interwave-stb. +config SND_JAZZ16 + tristate "Media Vision Jazz16" + depends on SND + select SND_OPL3_LIB + select SND_PCM + help + Say Y here to include support for Media Vision Jazz16 based + soundcards. + + You probably want to enable Jazz16 Plug and Play support + (CONFIG_JAZZ16PNP) also. + + To compile this driver as a module, choose M here: the module + will be called snd-jazz16. + config SND_OPL3SA2 tristate "Yamaha OPL3-SA2/SA3" depends on SND diff -rup linux-2.6.20.6-clean/sound/isa/sb/Makefile linux-2.6.20.6-ril/sound/isa/sb/Makefile --- linux-2.6.20.6-clean/sound/isa/sb/Makefile 2007-02-04 19:44:54.000000000 +0100 +++ linux-2.6.20.6-ril/sound/isa/sb/Makefile 2007-04-07 17:31:38.000000000 +0200 @@ -12,6 +12,7 @@ snd-sb16-objs := sb16.o snd-sbawe-objs := sbawe.o emu8000.o snd-emu8000-synth-objs := emu8000_synth.o emu8000_callback.o emu8000_patch.o emu8000_pcm.o snd-es968-objs := es968.o +snd-jazz16-objs := jazz16.o # # this function returns: @@ -30,6 +31,7 @@ obj-$(CONFIG_SND_SB16) += snd-sb16.o snd obj-$(CONFIG_SND_SBAWE) += snd-sbawe.o snd-sb16-dsp.o snd-sb-common.o obj-$(CONFIG_SND_ES968) += snd-es968.o snd-sb8-dsp.o snd-sb-common.o obj-$(CONFIG_SND_ALS4000) += snd-sb-common.o +obj-$(CONFIG_SND_JAZZ16) += snd-jazz16.o snd-sb8-dsp.o snd-sb-common.o ifeq ($(CONFIG_SND_SB16_CSP),y) obj-$(CONFIG_SND_SB16) += snd-sb16-csp.o obj-$(CONFIG_SND_SBAWE) += snd-sb16-csp.o diff -rup linux-2.6.20.6-clean/sound/isa/sb/sb8_main.c linux-2.6.20.6-ril/sound/isa/sb/sb8_main.c --- linux-2.6.20.6-clean/sound/isa/sb/sb8_main.c 2007-02-04 19:44:54.000000000 +0100 +++ linux-2.6.20.6-ril/sound/isa/sb/sb8_main.c 2007-04-12 00:03:35.000000000 +0200 @@ -28,6 +28,9 @@ * * Wed Jul 12 22:02:55 CEST 2000 Uros Bizjak <uros(a)kss-loka.si> * Cleaned up and rewrote lowlevel routines. + * + * Wed Apr 11 23:56:18 CEST 2007 Rask Ingemann Lambertsen <rask(a)sygehus.dk> + * Added Jazz16 enhancements (mostly ported from sound/oss/sb_common.c). */ #include <sound/driver.h> @@ -73,6 +76,15 @@ static struct snd_ratnum stereo_clocks[] } }; +/* For stereo playback and capture, the denominator is divided by two, so it + * must be even to get the intended sample rate. */ +static struct snd_ratnum jazz16_stereo_clock = { + .num = SB8_CLOCK, + .den_min = 2, + .den_max = 512, + .den_step = 2, +}; + static int snd_sb8_hw_constraint_rate_channels(struct snd_pcm_hw_params *params, struct snd_pcm_hw_rule *rule) { @@ -101,13 +113,52 @@ static int snd_sb8_hw_constraint_channel return 0; } +static int snd_jazz16_hw_constraint_rate_channels(struct snd_pcm_hw_params *params, + struct snd_pcm_hw_rule *rule) +{ + struct snd_interval *c = hw_param_interval(params, SNDRV_PCM_HW_PARAM_CHANNELS); + struct snd_interval *r = hw_param_interval(params, SNDRV_PCM_HW_PARAM_RATE); + int err = 0; + + if (c->max > 1) { + unsigned int num = 0, den = 0; + err = snd_interval_ratnum(r, 1, &jazz16_stereo_clock, &num, &den); + if (err >= 0 && den) { + params->rate_num = num; + params->rate_den = den; + } + } + return err; +} + +static int snd_jazz16_hw_constraint_channels_rate(struct snd_pcm_hw_params *params, + struct snd_pcm_hw_rule *rule) +{ + struct snd_interval *r = hw_param_interval(params, SNDRV_PCM_HW_PARAM_RATE); + int err = 0; + + /* Force mono mode if the sample rate interval doesn't allow stereo. */ + if (SB8_DEN(r->min) == SB8_DEN(r->max) + && SB8_DEN(r->min) & 1) + { + struct snd_interval t = { .min = 1, .max = 1 }; + struct snd_interval *c; + + c = hw_param_interval(params, SNDRV_PCM_HW_PARAM_CHANNELS); + err = snd_interval_refine(c, &t); + } + return err; +} + static int snd_sb8_playback_prepare(struct snd_pcm_substream *substream) { unsigned long flags; struct snd_sb *chip = snd_pcm_substream_chip(substream); struct snd_pcm_runtime *runtime = substream->runtime; unsigned int mixreg, rate, size, count; + unsigned char stereo, format; + stereo = runtime->channels > 1; rate = runtime->rate; switch (chip->hardware) { case SB_HW_PRO: @@ -123,6 +174,7 @@ static int snd_sb8_playback_prepare(stru break; } /* fallthru */ + case SB_HW_JAZZ16: case SB_HW_20: chip->playback_format = SB_DSP_LO_OUTPUT_AUTO; break; @@ -134,8 +186,14 @@ static int snd_sb8_playback_prepare(stru } size = chip->p_dma_size = snd_pcm_lib_buffer_bytes(substream); count = chip->p_period_size = snd_pcm_lib_period_bytes(substream); + if (runtime->format == SNDRV_PCM_FORMAT_S16_LE) + format = stereo ? SB_DSP_STEREO_16BIT : SB_DSP_MONO_16BIT; + else + format = stereo ? SB_DSP_STEREO_8BIT : SB_DSP_MONO_8BIT; spin_lock_irqsave(&chip->reg_lock, flags); snd_sbdsp_command(chip, SB_DSP_SPEAKER_ON); + if (chip->hardware == SB_HW_JAZZ16) + snd_sbdsp_command(chip, format); if (runtime->channels > 1) { /* set playback stereo mode */ spin_lock(&chip->mixer_lock); @@ -167,6 +225,8 @@ static int snd_sb8_playback_prepare(stru snd_sbdsp_command(chip, 256 - runtime->rate_den); } if (chip->playback_format != SB_DSP_OUTPUT) { + if (chip->dma8 > 3) + count /= 2; count--; snd_sbdsp_command(chip, SB_DSP_BLOCK_SIZE); snd_sbdsp_command(chip, count & 0xff); @@ -233,7 +293,9 @@ static int snd_sb8_capture_prepare(struc struct snd_sb *chip = snd_pcm_substream_chip(substream); struct snd_pcm_runtime *runtime = substream->runtime; unsigned int mixreg, rate, size, count; + unsigned char stereo, format; + stereo = runtime->channels > 1; rate = runtime->rate; switch (chip->hardware) { case SB_HW_PRO: @@ -250,6 +312,7 @@ static int snd_sb8_capture_prepare(struc break; } /* fallthru */ + case SB_HW_JAZZ16: case SB_HW_20: chip->capture_format = SB_DSP_LO_INPUT_AUTO; break; @@ -261,10 +324,14 @@ static int snd_sb8_capture_prepare(struc } size = chip->c_dma_size = snd_pcm_lib_buffer_bytes(substream); count = chip->c_period_size = snd_pcm_lib_period_bytes(substream); + if (runtime->format == SNDRV_PCM_FORMAT_S16_LE) + format = stereo ? SB_DSP_STEREO_16BIT : SB_DSP_MONO_16BIT; + else + format = stereo ? SB_DSP_STEREO_8BIT : SB_DSP_MONO_8BIT; spin_lock_irqsave(&chip->reg_lock, flags); snd_sbdsp_command(chip, SB_DSP_SPEAKER_OFF); - if (runtime->channels > 1) - snd_sbdsp_command(chip, SB_DSP_STEREO_8BIT); + if (stereo || chip->hardware == SB_HW_JAZZ16) + snd_sbdsp_command(chip, format); snd_sbdsp_command(chip, SB_DSP_SAMPLE_RATE); if (runtime->channels > 1) { snd_sbdsp_command(chip, 256 - runtime->rate_den / 2); @@ -279,6 +346,8 @@ static int snd_sb8_capture_prepare(struc snd_sbdsp_command(chip, 256 - runtime->rate_den); } if (chip->capture_format != SB_DSP_OUTPUT) { + if (chip->dma8 > 3) + count /= 2; count--; snd_sbdsp_command(chip, SB_DSP_BLOCK_SIZE); snd_sbdsp_command(chip, count & 0xff); @@ -443,6 +512,19 @@ static int snd_sb8_open(struct snd_pcm_s runtime->hw = snd_sb8_capture; } switch (chip->hardware) { + case SB_HW_JAZZ16: + runtime->hw.formats |= SNDRV_PCM_FMTBIT_S16_LE; + runtime->hw.rates |= SNDRV_PCM_RATE_8000_44100; + runtime->hw.rate_max = 45455; + runtime->hw.channels_max = 2; + snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_RATE, + snd_jazz16_hw_constraint_rate_channels, NULL, + SNDRV_PCM_HW_PARAM_CHANNELS, + SNDRV_PCM_HW_PARAM_RATE, -1); + snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS, + snd_jazz16_hw_constraint_channels_rate, NULL, + SNDRV_PCM_HW_PARAM_RATE, -1); + break; case SB_HW_PRO: runtime->hw.rate_max = 44100; runtime->hw.channels_max = 2; @@ -465,6 +547,14 @@ static int snd_sb8_open(struct snd_pcm_s } snd_pcm_hw_constraint_ratnums(runtime, 0, SNDRV_PCM_HW_PARAM_RATE, &hw_constraints_clock); + if (chip->dma8 > 3) { + snd_pcm_hw_constraint_step(runtime, 0, + SNDRV_PCM_HW_PARAM_BUFFER_BYTES, 2); + snd_pcm_hw_constraint_step(runtime, 0, + SNDRV_PCM_HW_PARAM_PERIOD_BYTES, 2); + runtime->hw.buffer_bytes_max = 128 * 1024 * 1024; + runtime->hw.period_bytes_max = 128 * 1024 * 1024; + } return 0; } @@ -512,6 +602,7 @@ int snd_sb8dsp_pcm(struct snd_sb *chip, struct snd_card *card = chip->card; struct snd_pcm *pcm; int err; + size_t max_prealloc; if (rpcm) *rpcm = NULL; @@ -524,9 +615,10 @@ int snd_sb8dsp_pcm(struct snd_sb *chip, snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_sb8_playback_ops); snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_sb8_capture_ops); + max_prealloc = (chip->dma8 > 3) ? 128 * 1024 : 64 * 1024; snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_DEV, snd_dma_isa_data(), - 64*1024, 64*1024); + 64*1024, max_prealloc); if (rpcm) *rpcm = pcm; diff -rup linux-2.6.20.6-clean/sound/isa/sb/sb_common.c linux-2.6.20.6-ril/sound/isa/sb/sb_common.c --- linux-2.6.20.6-clean/sound/isa/sb/sb_common.c 2007-02-04 19:44:54.000000000 +0100 +++ linux-2.6.20.6-ril/sound/isa/sb/sb_common.c 2007-04-11 20:23:55.000000000 +0200 @@ -146,8 +146,16 @@ static int snd_sbdsp_probe(struct snd_sb } break; case 3: - chip->hardware = SB_HW_PRO; - str = "Pro"; + spin_lock_irqsave(&chip->reg_lock, flags); + if (snd_sbdsp_command(chip, SB_DSP_GET_JAZZ_VERSION) && + SB_VERSION_IS_JAZZ16(snd_sbdsp_get_byte (chip))) { + chip->hardware = SB_HW_JAZZ16; + str = "Pro (Jazz16)"; + } else { + chip->hardware = SB_HW_PRO; + str = "Pro"; + } + spin_unlock_irqrestore (&chip->reg_lock, flags); break; case 4: chip->hardware = SB_HW_16; diff -rup linux-2.6.20.6-clean/sound/isa/sb/sb_mixer.c linux-2.6.20.6-ril/sound/isa/sb/sb_mixer.c --- linux-2.6.20.6-clean/sound/isa/sb/sb_mixer.c 2007-02-04 19:44:54.000000000 +0100 +++ linux-2.6.20.6-ril/sound/isa/sb/sb_mixer.c 2007-04-07 17:31:38.000000000 +0200 @@ -811,6 +811,7 @@ int snd_sbmixer_new(struct snd_sb *chip) return err; break; case SB_HW_PRO: + case SB_HW_JAZZ16: if ((err = snd_sbmixer_init(chip, snd_sbpro_controls, ARRAY_SIZE(snd_sbpro_controls), @@ -946,6 +947,7 @@ void snd_sbmixer_suspend(struct snd_sb * save_mixer(chip, sb20_saved_regs, ARRAY_SIZE(sb20_saved_regs)); break; case SB_HW_PRO: + case SB_HW_JAZZ16: save_mixer(chip, sbpro_saved_regs, ARRAY_SIZE(sbpro_saved_regs)); break; case SB_HW_16: @@ -971,6 +973,7 @@ void snd_sbmixer_resume(struct snd_sb *c restore_mixer(chip, sb20_saved_regs, ARRAY_SIZE(sb20_saved_regs)); break; case SB_HW_PRO: + case SB_HW_JAZZ16: restore_mixer(chip, sbpro_saved_regs, ARRAY_SIZE(sbpro_saved_regs)); break; case SB_HW_16: --- /dev/null 2007-04-11 19:30:17.320748640 +0200 +++ linux-2.6.20.6-ril/sound/isa/sb/jazz16.c 2007-04-05 23:30:27.000000000 +0200 @@ -0,0 +1,183 @@ +/* Driver for Media Vision Jazz16 based boards. + * + * Copyright (c) 2007 by Rask Ingemann Lambertsen + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * The Jazz16 is an SB Pro compatible chip with a 16-bit mode and higher + * playback and capture rates added to it. It is not SB 16 compatible. + * There is also an MPU-401 interface. + * + * AFAIK, the following systems have an on-board Jazz16 chip: + * IBM PPS Model 6015 + * Texas Intstruments/Acer Travelmate TM5000 series. + * Please tell me if this driver works with these boards or not. + */ + +#include <sound/driver.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/pnp.h> +#include <linux/ioport.h> +#include <asm/io.h> +#include <linux/delay.h> +#include <sound/core.h> +#include <sound/sb.h> +#include <sound/mpu401.h> +#include <sound/opl3.h> +#include <sound/initval.h> + +MODULE_AUTHOR("Rask Ingemann Lambertsen <rask(a)sygehus.dk>"); +MODULE_DESCRIPTION("Jazz16"); +MODULE_LICENSE("GPL"); + +static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; /* Index 0-MAX */ +static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; /* ID for this card */ +static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP; /* Enable switches */ + +module_param_array(index, int, NULL, 0444); +MODULE_PARM_DESC(index, "Index value for Jazz16 soundcard."); +module_param_array(id, charp, NULL, 0444); +MODULE_PARM_DESC(id, "ID string for Jazz16 soundcard."); +module_param_array(enable, bool, NULL, 0444); +MODULE_PARM_DESC(enable, "Enable Jazz16 soundcard."); + +#define PFX "jazz16: " +#define PFX_WARN KERN_WARNING PFX +#define PFX_ERR KERN_ERR PFX + +static struct pnp_driver snd_jazz16_pnp_driver; + +static irqreturn_t jazz16_interrupt(int irq, void *card) +{ + return snd_sb8dsp_interrupt(card); +} + +static struct pnp_device_id snd_jazz16_pnpids[] = { + { .id = "PNPb00f" }, + { .id = "" } +}; +MODULE_DEVICE_TABLE(pnp, snd_jazz16_pnpids); + +static int __devinit snd_jazz16_pnp_probe(struct pnp_dev *pnp_dev, + const struct pnp_device_id *pnp_id) +{ struct snd_sb *chip; + struct snd_card *card; + struct snd_opl3 *opl3; + int err; + uint sbport, sbirq, sbdma, mpuport, mpuirq; + static uint dev_num = 0; + + if (enable[dev_num]) + card = snd_card_new(index[dev_num], id[dev_num], THIS_MODULE, 0); + else + card = NULL; + dev_num++; + if (card == NULL) + return enable[dev_num] ? -ENOMEM : -ENODEV; + snd_card_set_dev(card, &pnp_dev->dev); + pnp_set_drvdata(pnp_dev, card); + /* TODO use pnp_port_valid(), pnp_port_flags(), pnp_port_length()... */ + sbport = pnp_port_start(pnp_dev, 0); + sbirq = pnp_irq(pnp_dev, 0); + sbdma = pnp_dma(pnp_dev, 0); + err = snd_sbdsp_create(card, sbport, sbirq, jazz16_interrupt, + sbdma, -1, SB_HW_AUTO, &chip); + if (err < 0) + goto out_err; + + strcpy(card->driver, "Jazz16"); + strcpy(card->shortname, "Media Vision Jazz16"); + sprintf(card->longname, "%s at %#x, irq %u, dma %u", + chip->name, sbport, sbirq, chip->dma8); + + if (chip->hardware != SB_HW_JAZZ16) { + snd_printk(PFX_ERR "Not a Jazz16 chip at %#x.\n", sbport); + snd_card_free(card); + return -ENODEV; + } + err = snd_sb8dsp_pcm(chip, 0, NULL); + if (err < 0) + goto out_err; + + err = snd_sbmixer_new(chip); + if (err < 0) + goto out_err; + + err = snd_opl3_create(card, sbport, sbport + 2, + OPL3_HW_AUTO, 1, &opl3); + if (err < 0) + snd_printk(PFX_WARN "No OPL device found, skipping.\n"); + else { + err = snd_opl3_timer_new(opl3, 1, 2); + if (err < 0) + goto out_err; + err = snd_opl3_hwdep_new(opl3, 0, 1, NULL); + if (err < 0) + goto out_err; + } + if (pnp_port_valid(pnp_dev, 1) + && !(pnp_port_flags(pnp_dev, 1) & IORESOURCE_DISABLED)) { + int mpuirqflags; + if (!pnp_irq_valid(pnp_dev, 1) + || pnp_irq_flags(pnp_dev, 1) & IORESOURCE_DISABLED) { + mpuirq = -1; + mpuirqflags = 0; + } else { + mpuirq = pnp_irq(pnp_dev, 1); + mpuirqflags = IRQF_DISABLED; + } + mpuport = pnp_port_start(pnp_dev, 1); + err = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401, + mpuport, 0, mpuirq, + mpuirqflags, NULL); + if (err < 0) + snd_printk(PFX_WARN "MPU-401 device not configured, skipping.\n"); + } + err = snd_card_register(card); + if (err >= 0) + return 0; +out_err: + snd_card_free(card); + return err; +} + +static void __devexit snd_jazz16_pnp_remove(struct pnp_dev *dev) +{ + snd_card_free(pnp_get_drvdata(dev)); + pnp_set_drvdata(dev, NULL); +} + +static struct pnp_driver snd_jazz16_pnp_driver = { + .name = "Jazz16", + .id_table = snd_jazz16_pnpids, + .probe = snd_jazz16_pnp_probe, + .remove = __devexit_p(snd_jazz16_pnp_remove), +}; + +static int __devinit alsa_card_jazz16_init(void) +{ + return pnp_register_driver(&snd_jazz16_pnp_driver); +} + +static void __devexit alsa_card_jazz16_exit(void) +{ + pnp_unregister_driver(&snd_jazz16_pnp_driver); +} + +module_init(alsa_card_jazz16_init); +module_exit(alsa_card_jazz16_exit); -- Rask Ingemann Lambertsen

3 3

[alsa-devel] [Alsa-devel] Read the input of a soundcard with ALSA
by Nyx 20 Apr '07

20 Apr '07

Hi, I have some problems to read the input of my soundcard using Alsa and I don't really understand how to have access to the input of my soundcard. I follow : http://www.alsa-project.org/alsa-doc/alsa-lib/_2test_2pcm_8c-example.html http://www.alsa-project.org/alsa-doc/alsa-lib/_2test_2latency_8c-example.ht… # So, in my program, I have created two handles for capture and playback : char *device = "hw:0,0"; snd_output_t *output; snd_input_t *input; snd_pcm_t *phandle, *chandle; # then I connect the phandle to the out err = snd_output_stdio_attach(&output, stdout, 0); if (..) # Do I have to connect the chandle with the input ? # err = snd_input_stdio_attach(&input, stdin, 0); # I open the access to PCM err = snd_pcm_open(&phandle, pdevice, SND_PCM_STREAM_PLAYBACK, 0) if (..) err = snd_pcm_open(&chandle, pdevice, SND_PCM_STREAM_CAPTURE, 0) if(..) # Hardware and software Parameters ## Hardware Parameters snd_pcm_hw_params; int err; err = snd_pcm_hw_params_any(phandle, params); if(..); err = snd_pcm_hw_params_set_access(phandle, params,SND_PCM_ACCESS_RW_INTERLEAVED); if(..); err = snd_pcm_hw_params_set_format(phandle, params,SND_PCM_FORMAT_S16); if(..); err = snd_pcm_hw_params_set_channels(phandle, params, 1); if(..); err = snd_pcm_hw_params_set_rate_near(phandle, params, 44100, 0); if(..); err = snd_pcm_hw_params_set_buffer_time_near(phandle, params, 500000, &dir); if(..); err = snd_pcm_hw_params_set_time_near(phandle, params, 100000, &dir), if(..); err = snd_pcm_hw_params(phandle, params); ##Software parameters err = snd_pcm_sw_params(phandle, params); if(..); err = snd_pcm_sw_params_set_start_threshold(phandle, swparams, 0x7fffffff); if(..); err = snd_pcm_sw_params_set_avail_min(phandle, swparams, 4); # same configuration for phandle # Link output to input and start err = snd_pcm_link(chandle, phandle); if(..); err = snd_pcm_start(chandle); if(..); #Then I want to read my input frames_in = 0; in_max = 0; latency = 28; buffer = malloc((latency_max * snd_pcm_format_width(format) / 8) * 2); while (1) { r = readbuf(chandle, buffer, latency, &frames_in, &in_max)); if(..); } # description of the function long readbuf(snd_pcm_t *handle, char *buf, long len, size_t *frames, size_t *max) { long r; do { r = snd_pcm_readi(handle, buf, len); } while (r == -EAGAIN); if (r > 0) { *frames += r; if ((long)*max < r) *max = r; } printf ("r = %s, len %li and buf[%d] %f \r", snd_strerror(r), len,i, buf[i]); return r; } So I compile it and I run it, and I have $ read = Broken Pipe, len = 28 and buf[..] = 0.000 Anyone can help me to read the input of my sound card ? Thank you -- K

1 0

Re: [alsa-devel] [PATCH 16/16] alsa sound support for mips
by Ralf Baechle 20 Apr '07

20 Apr '07

On Sun, Apr 15, 2007 at 11:26:05PM +0800, tiansm(a)lemote.com wrote: (Adding a few more people to the cc'list) > sound/core/pcm_native.c | 10 ++++++++++ > sound/core/sgbuf.c | 9 +++++++++ > 2 files changed, 19 insertions(+), 0 deletions(-) > > diff --git a/sound/core/pcm_native.c b/sound/core/pcm_native.c > index 3e276fc..9005bac 100644 > --- a/sound/core/pcm_native.c > +++ b/sound/core/pcm_native.c > @@ -3145,7 +3145,11 @@ static struct page *snd_pcm_mmap_data_nopage(struct vm_area_struct *area, > return NOPAGE_OOM; /* XXX: is this really due to OOM? */ > } else { > vaddr = runtime->dma_area + offset; > +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT) Please use CONFIG_MIPS instead of __mips__ in #if / #ifdefs. The question if #ifdefing is the right approach to solve this problem is something else but I think no, .... > + page = virt_to_page(CAC_ADDR(vaddr)); > +#else > page = virt_to_page(vaddr); > +#endif So this is needed because the MIPS virt_to_page is returning a unsuitable value if vaddress is not a KSEG0 (64-bit: cached XKPHYS) address which is what GFP allocations and the slab will return. So now we have to deciede if a) the MIPS __pa() should be changed to handle uncached addresses. b) the sound code here is simply broken. Some drivers seem to allocate runtime->dma_area from vmalloc, so this whole area in the sound code is looking like built on quicksand ... > } > get_page(page); > if (type) > @@ -3261,6 +3265,12 @@ static int snd_pcm_mmap(struct file *file, struct vm_area_struct *area) > substream = pcm_file->substream; > snd_assert(substream != NULL, return -ENXIO); > > +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT) > + /* all mmap using uncached mode */ > + area->vm_page_prot = pgprot_noncached(area->vm_page_prot); > + area->vm_flags |= ( VM_RESERVED | VM_IO); VM_RESERVED will prevent the buffer from being freed. I assume that is another workaround for some kernel subsystem blowing up when being fed a pointer to an uncached RAM address? This smells like a memory leak. > +#endif > + > offset = area->vm_pgoff << PAGE_SHIFT; > switch (offset) { > case SNDRV_PCM_MMAP_OFFSET_STATUS: > diff --git a/sound/core/sgbuf.c b/sound/core/sgbuf.c > index cefd228..535f0bc 100644 > --- a/sound/core/sgbuf.c > +++ b/sound/core/sgbuf.c > @@ -91,12 +91,21 @@ void *snd_malloc_sgbuf_pages(struct device *device, > } > sgbuf->table[i].buf = tmpb.area; > sgbuf->table[i].addr = tmpb.addr; > +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT) > + sgbuf->page_table[i] = virt_to_page(CAC_ADDR(tmpb.area)); VM_RESERVED will prevent the buffer from being freed. I assume that is another workaround for some kernel subsystem blowing up when being fed a pointer to an uncached RAM address? This smells like a memory leak. > +#else > sgbuf->page_table[i] = virt_to_page(tmpb.area); > +#endif > sgbuf->pages++; > } > > sgbuf->size = size; > +#if defined(__mips__) && defined(CONFIG_DMA_NONCOHERENT) > + /* maybe we should use uncached accelerated mode */ > + dmab->area = vmap(sgbuf->page_table, sgbuf->pages, VM_MAP | VM_IO, pgprot_noncached(PAGE_KERNEL)); > +#else > dmab->area = vmap(sgbuf->page_table, sgbuf->pages, VM_MAP, PAGE_KERNEL); > +#endif I would suggest to get rid of this ifdef with a new arch-specific function like vmap_io_buffer which will do whatever a platform seems fit for this case? > if (! dmab->area) > goto _failed; > return dmab->area; Ralf

3 2

[alsa-devel] Trying to support hda-intel ALC883_CLEVO
by Pablo N. Hess 19 Apr '07

19 Apr '07

I have a Clevo M600 notebook, which comes with Realtek's HDA Intel audio chip. 'lspci -vn' says: 00:1b.0 0403: 8086:27d8 (rev 02) Subsystem: 1558:0660 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at 6c340000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Unknown type IRQ 0 Capabilities: [100] Virtual Channel Capabilities: [130] Unknown (5) Linux 2.6.20 (Gentoo's gentoo-sources-2.6.20r4) recognizes it as an ALC883 chip, but no parameter combination would make the sound work properly (and that includes 'model=clevo'). As this module ships, no output would come from the built-in speakers, and the headphone volume was miserably low. patch_realtek.c supports vendor=1558 device=0660, but only as a ALC880 chip. However, mine *is* an ALC883 vendor=1558 device=0660. After copying the ALC880_CLEVO support code lines into a new ALC883_CLEVO (and changing every occurence of ALC880 to ALC883 in that new code block), recompiling the kernel and loading the snd-hda-intel with model=clevo, almost everything started working fine. I mean, sound comes as perfectly as it can through the built-in speakers, and the built-in mic also outputs its sound through these speakers. However, I can't capture anything. Alsamixer shows no capture device at all (although all playback devices appear to be present). This is very strange to me, as the built-in mic really *does* output its sound through the speakers. As you can probably see, I don't know anything about sound chips. I just did what seemed understandable (to me) to add proper support for my ALC883_CLEVO device. Thank you very much if you can help me solve this issue, as I really need to speak with my family and girlfriend far, far away. Cheers, Pablo Hess

2 1

[alsa-devel] [KJ][PATCH] sound: SPIN_LOCK_UNLOCKED cleanup
by Milind Arun Choudhary 19 Apr '07

19 Apr '07

SPIN_LOCK_UNLOCKED cleanup,use __SPIN_LOCK_UNLOCKED instead Signed-off-by: Milind Arun Choudhary <milindchoudhary(a)gmail.com> --- soc/at91/at91-i2s.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/sound/soc/at91/at91-i2s.c b/sound/soc/at91/at91-i2s.c index 9fc0c03..d65a47d 100644 --- a/sound/soc/at91/at91-i2s.c +++ b/sound/soc/at91/at91-i2s.c @@ -151,20 +151,20 @@ static struct at91_ssc_info { } ssc_info[NUM_SSC_DEVICES] = { { .name = "ssc0", - .lock = SPIN_LOCK_UNLOCKED, + .lock = __SPIN_LOCK_UNLOCKED(ssc_info[0].lock), .dir_mask = 0, .initialized = 0, }, #if NUM_SSC_DEVICES == 3 { .name = "ssc1", - .lock = SPIN_LOCK_UNLOCKED, + .lock = __SPIN_LOCK_UNLOCKED(ssc_info[1].lock), .dir_mask = 0, .initialized = 0, }, { .name = "ssc2", - .lock = SPIN_LOCK_UNLOCKED, + .lock = __SPIN_LOCK_UNLOCKED(ssc_info[2].lock), .dir_mask = 0, .initialized = 0, }, -- Milind Arun Choudhary

1 0

[alsa-devel] CS4270 supported?
by Timur Tabi 19 Apr '07

19 Apr '07

I've never worked with ALSA before, but I'm about to start developing on an ALSA driver for our hardware, which has a CS4270 on it attached via an I2S interface. After scanning the source code and mailing lists, I see no mention of the CS4270. So does that mean I would need to write an ASoC codec driver for the CS4270? If so, does the data sheet (http://www.cirrus.com/en/pubs/proDatasheet/CS4270_PP1.pdf) contain enough information? -- Timur Tabi Linux Kernel Developer @ Freescale

4 7

[alsa-devel] Trying to support hda-intel ALC883_CLEVO
by natunobilis＠gentoobr.org 19 Apr '07

19 Apr '07

I have a Clevo M600 notebook, which comes with Realtek's HDA Intel audio chip. 'lspci -vn' says: 00:1b.0 0403: 8086:27d8 (rev 02) Subsystem: 1558:0660 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at 6c340000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Unknown type IRQ 0 Capabilities: [100] Virtual Channel Capabilities: [130] Unknown (5) Linux 2.6.20 (Gentoo's gentoo-sources-2.6.20r4) recognizes it as an ALC883 chip, but no parameter combination would make the sound work properly (and that includes 'model=clevo'). As this module ships, no output would come from the built-in speakers, and the headphone volume was miserably low. patch_realtek.c supports vendor=1558 device=0660, but only as a ALC880 chip. However, mine *is* an ALC883 vendor=1558 device=0660. After copying the ALC880_CLEVO support code lines into a new ALC883_CLEVO (and changing every occurence of ALC880 to ALC883 in that new code block), recompiling the kernel and loading the snd-hda-intel with model=clevo, almost everything started working fine. I mean, sound comes as perfectly as it can through the built-in speakers, and the built-in mic also outputs its sound through these speakers. However, I can't capture anything. Alsamixer shows no capture device at all (although all playback devices appear to be present). This is very strange to me, as the built-in mic really *does* output its sound through the speakers. As you can probably see, I don't know anything about sound chips. I just did what seemed understandable (to me) to add proper support for my ALC883_CLEVO device. Thank you very much if you can help me solve this issue, as I really need to speak with my family and girlfriend far, far away. Cheers, Pablo Hess

1 0

[alsa-devel] Surround problems on ALC883
by Pavel Patz 18 Apr '07

18 Apr '07

Hi all, I have problems with chip Realtek ALC883 (lspci: 00:06.1 Audio device: nVidia Corporation MCP55 High Definition Audio (rev a2)) and surround sound. Stereo sound is working (games, music) fine - all 6 speaker are playing. But when I tried to run "aplay chan-id.wav", i've heard only "front left" (front & rear left + center were playing) and "front right" (right front & rear were playing), then was silence until the end of the file. Running "aplay -Dsurround51 chan-id.wav" causes that aplay hangs-up without any output. Running it with -v parameter produces this output: Playing WAVE 'Desktop/Surround-SDL-testfiles/chan-id.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Channels 6 Soft volume PCM Control: PCM Playback Volume min_dB: -51 resolution: 256 Its setup is: stream : PLAYBACK access : RW_INTERLEAVED format : S16_LE subformat : STD channels : 6 rate : 44100 exact rate : 44100 (44100/1) msbits : 16 buffer_size : 5460 period_size : 1365 period_time : 30952 tick_time : 1000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 1365 xfer_align : 1365 start_threshold : 5460 stop_threshold : 5460 silence_threshold: 0 silence_size : 0 boundary : 6147413491360727040 Slave: Hardware PCM card 0 'HDA NVidia' device 0 subdevice 0 Its setup is: stream : PLAYBACK access : MMAP_INTERLEAVED format : S16_LE subformat : STD channels : 6 rate : 44100 exact rate : 44100 (44100/1) msbits : 16 buffer_size : 5460 period_size : 1365 period_time : 30952 tick_time : 1000 tstamp_mode : NONE period_step : 1 sleep_min : 0 avail_min : 1365 xfer_align : 1365 start_threshold : 5460 stop_threshold : 5460 silence_threshold: 0 silence_size : 0 boundary : 6147413491360727040 and then hang up until i press ctrl+c. Same results i get with speaker-test. I'm using alsa-lib-1.0.14-0.4.rc3.fc7 I've found similar problem in archive (about half a year old) but it still seems it isn't working. Is there any possibility, that this will be fixed in future? Thanks for all your help (and please leave me in CC, i'm not on mailing-list). Following lsmod & /proc/asound/card0/codec#0 [cdome@andromeda ~]$ /sbin/lsmod |grep snd snd_hda_intel 27936 2 snd_hda_codec 262400 1 snd_hda_intel snd_seq_dummy 11908 0 snd_seq_oss 40448 0 snd_seq_midi_event 16128 1 snd_seq_oss snd_seq 60704 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 16404 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 50944 0 snd_mixer_oss 24320 2 snd_pcm_oss snd_pcm 90888 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd_timer 30088 2 snd_seq,snd_pcm snd 67624 12 snd_hda_intel,snd_hda_codec,snd_seq_dummy,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer soundcore 17505 2 snd snd_page_alloc 16912 2 snd_hda_intel,snd_pcm [cdome@andromeda ~]$ cat /proc/asound/card0/codec#0 Codec: Realtek ALC883 Address: 0 Vendor Id: 0x10ec0883 Subsystem Id: 0x1458e601 Revision Id: 0x100002 Default PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Default Amp-In caps: N/A Default Amp-Out caps: N/A Node 0x02 [Audio Output] wcaps 0x11: Stereo PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x03 [Audio Output] wcaps 0x11: Stereo PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x04 [Audio Output] wcaps 0x11: Stereo PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x05 [Audio Output] wcaps 0x11: Stereo PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x06 [Audio Output] wcaps 0x211: Stereo Digital PCM: rates [0x560]: 44100 48000 96000 192000 bits [0x1e]: 16 20 24 32 formats [0x1]: PCM Node 0x07 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x08 [Audio Input] wcaps 0x10011b: Stereo Amp-In Amp-In caps: ofs=0x08, nsteps=0x1f, stepsize=0x05, mute=1 Amp-In vals: [0x10 0x10] PCM: rates [0x160]: 44100 48000 96000 bits [0x6]: 16 20 formats [0x1]: PCM Connection: 1 0x23 Node 0x09 [Audio Input] wcaps 0x10011b: Stereo Amp-In Amp-In caps: ofs=0x08, nsteps=0x1f, stepsize=0x05, mute=1 Amp-In vals: [0x00 0x00] PCM: rates [0x160]: 44100 48000 96000 bits [0x6]: 16 20 formats [0x1]: PCM Connection: 1 0x22 Node 0x0a [Audio Input] wcaps 0x100391: Stereo Digital PCM: rates [0x560]: 44100 48000 96000 192000 bits [0x1e]: 16 20 24 32 formats [0x1]: PCM Connection: 1 0x1f Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1 Amp-In vals: [0x80 0x80] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x17 0x17] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] Connection: 10 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 Node 0x0c [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 Amp-Out vals: [0x1a 0x1a] Connection: 2 0x02 0x0b Node 0x0d [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 Amp-Out vals: [0x1a 0x1a] Connection: 2 0x03 0x0b Node 0x0e [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 Amp-Out vals: [0x1a 0x04] Connection: 2 0x04 0x0b Node 0x0f [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 Amp-Out vals: [0x00 0x00] Connection: 2 0x05 0x0b Node 0x10 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x12 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x13 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x14 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00] Pincap 0x083e: IN OUT HP Detect Pin Default 0x01014410: [Jack] Line Out at Ext Rear Conn = 1/8, Color = Green Pin-ctls: 0x40: OUT Connection: 5 0x0c* 0x0d 0x0e 0x0f 0x26 Node 0x15 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00] Pincap 0x083e: IN OUT HP Detect Pin Default 0x01011412: [Jack] Line Out at Ext Rear Conn = 1/8, Color = Black Pin-ctls: 0x40: OUT Connection: 5 0x0c 0x0d* 0x0e 0x0f 0x26 Node 0x16 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00] Pincap 0x083e: IN OUT HP Detect Pin Default 0x01016411: [Jack] Line Out at Ext Rear Conn = 1/8, Color = Orange Pin-ctls: 0x40: OUT Connection: 5 0x0c 0x0d 0x0e* 0x0f 0x26 Node 0x17 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x00 0x00] Pincap 0x083e: IN OUT HP Detect Pin Default 0x01012414: [Jack] Line Out at Ext Rear Conn = 1/8, Color = Grey Pin-ctls: 0x40: OUT Connection: 5 0x0c 0x0d 0x0e 0x0f* 0x26 Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x08173e: IN OUT HP Detect Pin Default 0x01a19c40: [Jack] Mic at Ext Rear Conn = 1/8, Color = Pink Pin-ctls: 0x24: IN Connection: 5 0x0c* 0x0d 0x0e 0x0f 0x26 Node 0x19 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x08173e: IN OUT HP Detect Pin Default 0x02a19c50: [Jack] Mic at Ext Front Conn = 1/8, Color = Pink Pin-ctls: 0x24: IN Connection: 5 0x0c* 0x0d 0x0e 0x0f 0x26 Node 0x1a [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x08173e: IN OUT HP Detect Pin Default 0x01813c41: [Jack] Line In at Ext Rear Conn = 1/8, Color = Blue Pin-ctls: 0x20: IN Connection: 5 0x0c* 0x0d 0x0e 0x0f 0x26 Node 0x1b [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-Out vals: [0x80 0x80] Pincap 0x08173e: IN OUT HP Detect Pin Default 0x02214c20: [Jack] HP Out at Ext Front Conn = 1/8, Color = Green Pin-ctls: 0xc0: OUT HP Connection: 5 0x0c* 0x0d 0x0e 0x0f 0x26 Node 0x1c [Pin Complex] wcaps 0x400001: Stereo Pincap 0x0820: IN Pin Default 0x9933014f: [Fixed] CD at Int ATAPI Conn = ATAPI, Color = Unknown Pin-ctls: 0x00: Node 0x1d [Pin Complex] wcaps 0x400000: Mono Pincap 0x0820: IN Pin Default 0x411111f0: [N/A] Speaker at Ext Rear Conn = 1/8, Color = Black Pin-ctls: 0x00: Node 0x1e [Pin Complex] wcaps 0x400300: Mono Digital Pincap 0x0810: OUT Pin Default 0x014b6130: [Jack] SPDIF Out at Ext Rear Conn = Comb, Color = Orange Pin-ctls: 0x00: Connection: 1 0x06 Node 0x1f [Pin Complex] wcaps 0x400200: Mono Digital Pincap 0x0820: IN Pin Default 0x01cb7160: [Jack] SPDIF In at Ext Rear Conn = Comb, Color = Yellow Pin-ctls: 0x00: Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x22 [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] Amp-Out caps: N/A Amp-Out vals: [0x00 0x00] Connection: 11 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b Node 0x23 [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] [0x00 0x00] [0x80 0x80] [0x00 0x00] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] [0x80 0x80] Amp-Out caps: N/A Amp-Out vals: [0x00 0x00] Connection: 11 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x14 0x15 0x16 0x17 0x0b Node 0x24 [Vendor Defined Widget] wcaps 0xf00000: Mono Node 0x25 [Audio Output] wcaps 0x11: Stereo PCM: rates [0x560]: 44100 48000 96000 192000 bits [0xe]: 16 20 24 formats [0x1]: PCM Node 0x26 [Audio Mixer] wcaps 0x20010f: Stereo Amp-In Amp-Out Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1 Amp-In vals: [0x00 0x00] [0x00 0x00] Amp-Out caps: ofs=0x1f, nsteps=0x1f, stepsize=0x05, mute=0 Amp-Out vals: [0x00 0x00] Connection: 2 0x25 0x0b

3 8

[alsa-devel] snd_pcm_hardware_t.info question
by Ciaccia 18 Apr '07

18 Apr '07

Hi all, I am trying to fix (improve?) a driver for an embedded ARM device I bought months ago, and for some reasons some ALSA applications work fine while other ones don't... Looking at the driver I got, I noticed that the info field in the snd_pcm_hardware_t struct just defines: SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_PAUSE while the info in the tutorial "writing an alsa driver" defines: SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_INTERLEAVED | SNDRV_PCM_INFO_BLOCK_TRANSFER | SNDRV_PCM_INFO_MMAP_VALID Furthermore, the driver defines a copy callback (actually 2, one for playback and one for capture), where it copies the data from the use space to the dma buffer. Since the dma buffer was preallocated with snd_pcm_lib_preallocate_pages_for_all and is accessible from the "outside", I wonder why the original author did this... I have some questions for you gurus: - what is the difference between SNDRV_PCM_INFO_MMAP and SNDRV_PCM_INFO_MMAP_VALID? What is SNDRV_PCM_INFO_BLOCK_TRANSFER? - The code calls snd_pcm_lib_preallocate_pages_for_all function as following: /* allocate the pcm(DMA) memory */ ret = snd_pcm_lib_preallocate_pages_for_all(pcm, SNDRV_DMA_TYPE_DEV,0, 4*128*1024, 4*128*1024); is the DMA_TYPE right for an ARM device? Is NULL a correct value for data in this case? - In case I get rid of the copy callback, how do I specify the format of the stream? How does Where can I find an example for that? Thanks a lot Andrea __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

2 5

[alsa-devel] [PATCH] sound: convert "sound" subdirectory to UTF-8
by John Anthony Kazos Jr. 17 Apr '07

17 Apr '07

From: John Anthony Kazos Jr. <jakj(a)j-a-k-j.com> Convert the "sound" subdirectory to UTF-8. The following files are changed. sound/oss/{trident.c,es1371.c,pas2_pcm.c} sound/oss/emu10k1/{passthrough.h,passthrough.c} sound/pci/mixart/mixart.c Signed-off-by: John Anthony Kazos Jr. <jakj(a)j-a-k-j.com> --- I can't get my mail client to send in ISO-8859-1 explicitly instead of whatever it decides I want, so the actual patch is attached in octet-stream format. The below patch is just for reference and will very likely NOT work, unless this time it picks ISO-8859-1. Also, since the patch includes both encodings, whichever encoding you select while viewing it will display one correct and one garbled line. However, the bytecodes -are- correct. diff -uprN linux-2.6.21-rc7.orig/sound/oss/emu10k1/passthrough.c linux-2.6.21-rc7.mod/sound/oss/emu10k1/passthrough.c --- linux-2.6.21-rc7.orig/sound/oss/emu10k1/passthrough.c 2007-02-04 13:44:54.000000000 -0500 +++ linux-2.6.21-rc7.mod/sound/oss/emu10k1/passthrough.c 2007-04-17 13:55:45.000000000 -0400 @@ -1,13 +1,13 @@ /* ********************************************************************** * passthrough.c -- Emu10k1 digital passthrough - * Copyright (C) 2001 Juha Yrjölä <jyrjola(a)cc.hut.fi> + * Copyright (C) 2001 Juha YrjÃ¶lÃ¤ <jyrjola(a)cc.hut.fi> * ********************************************************************** * * Date Author Summary of changes * ---- ------ ------------------ - * May 15, 2001 Juha Yrjölä base code release + * May 15, 2001 Juha YrjÃ¶lÃ¤ base code release * ********************************************************************** * diff -uprN linux-2.6.21-rc7.orig/sound/oss/emu10k1/passthrough.h linux-2.6.21-rc7.mod/sound/oss/emu10k1/passthrough.h --- linux-2.6.21-rc7.orig/sound/oss/emu10k1/passthrough.h 2007-02-04 13:44:54.000000000 -0500 +++ linux-2.6.21-rc7.mod/sound/oss/emu10k1/passthrough.h 2007-04-17 13:55:45.000000000 -0400 @@ -1,13 +1,13 @@ /* ********************************************************************** * passthrough.h -- Emu10k1 digital passthrough header file - * Copyright (C) 2001 Juha Yrjölä <jyrjola(a)cc.hut.fi> + * Copyright (C) 2001 Juha YrjÃ¶lÃ¤ <jyrjola(a)cc.hut.fi> * ********************************************************************** * * Date Author Summary of changes * ---- ------ ------------------ - * May 15, 2001 Juha Yrjölä base code release + * May 15, 2001 Juha YrjÃ¶lÃ¤ base code release * ********************************************************************** * diff -uprN linux-2.6.21-rc7.orig/sound/oss/es1371.c linux-2.6.21-rc7.mod/sound/oss/es1371.c --- linux-2.6.21-rc7.orig/sound/oss/es1371.c 2007-04-17 11:42:18.000000000 -0400 +++ linux-2.6.21-rc7.mod/sound/oss/es1371.c 2007-04-17 13:55:45.000000000 -0400 @@ -100,7 +100,7 @@ * Tjeerd Mulder <tjeerd.mulder(a)fujitsu-siemens.com> * 05.01.2001 0.29 Hopefully updates will not be required anymore when Creative bumps * the CT5880 revision. - * suggested by Stephan Müller <smueller(a)chronox.de> + * suggested by Stephan MÃ¼ller <smueller(a)chronox.de> * 31.01.2001 0.30 Register/Unregister gameport * Fix SETTRIGGER non OSS API conformity * 14.07.2001 0.31 Add list of laptops needing amplifier control diff -uprN linux-2.6.21-rc7.orig/sound/oss/pas2_pcm.c linux-2.6.21-rc7.mod/sound/oss/pas2_pcm.c --- linux-2.6.21-rc7.orig/sound/oss/pas2_pcm.c 2007-02-04 13:44:54.000000000 -0500 +++ linux-2.6.21-rc7.mod/sound/oss/pas2_pcm.c 2007-04-17 13:55:45.000000000 -0400 @@ -85,7 +85,7 @@ static int pcm_set_speed(int arg) * come from the SDK found on ftp.uwp.edu:/pub/msdos/proaudio/. * * I cleared bit 5 of these values, since that bit controls the master - * mute flag. (Olav Wölfelschneider) + * mute flag. (Olav WÃ¶lfelschneider) * */ #if !defined NO_AUTO_FILTER_SET diff -uprN linux-2.6.21-rc7.orig/sound/oss/trident.c linux-2.6.21-rc7.mod/sound/oss/trident.c --- linux-2.6.21-rc7.orig/sound/oss/trident.c 2007-04-17 11:42:18.000000000 -0400 +++ linux-2.6.21-rc7.mod/sound/oss/trident.c 2007-04-17 13:55:45.000000000 -0400 @@ -18,7 +18,7 @@ * Ollie Lho <ollie(a)sis.com.tw> SiS 7018 Audio Core Support * Ching-Ling Lee <cling-li(a)ali.com.tw> ALi 5451 Audio Core Support * Matt Wu <mattwu(a)acersoftech.com.cn> ALi 5451 Audio Core Support - * Peter Wächtler <pwaechtler(a)loewe-komp.de> CyberPro5050 support + * Peter WÃ¤chtler <pwaechtler(a)loewe-komp.de> CyberPro5050 support * Muli Ben-Yehuda <mulix(a)mulix.org> * * @@ -89,7 +89,7 @@ * use set_current_state, properly release resources on failure in * trident_probe, get rid of check_region * v0.14.9c - * August 10 2001 Peter Wächtler <pwaechtler(a)loewe-komp.de> + * August 10 2001 Peter WÃ¤chtler <pwaechtler(a)loewe-komp.de> * added support for Tvia (formerly Integraphics/IGST) CyberPro5050 * this chip is often found in settop boxes (combined video+audio) * v0.14.9b diff -uprN linux-2.6.21-rc7.orig/sound/pci/mixart/mixart.c linux-2.6.21-rc7.mod/sound/pci/mixart/mixart.c --- linux-2.6.21-rc7.orig/sound/pci/mixart/mixart.c 2007-02-04 13:44:54.000000000 -0500 +++ linux-2.6.21-rc7.mod/sound/pci/mixart/mixart.c 2007-04-17 13:55:45.000000000 -0400 @@ -472,7 +472,7 @@ static int snd_mixart_prepare(struct snd struct snd_mixart *chip = snd_pcm_substream_chip(subs); struct mixart_stream *stream = subs->runtime->private_data; - /* TODO de façon non bloquante, réappliquer les hw_params (rate, bits, codec) */ + /* TODO de faÃ§on non bloquante, rÃ©appliquer les hw_params (rate, bits, codec) */ snd_printdd("snd_mixart_prepare\n");

1 0