[alsa-devel] [PATCH v2 08/12] ARM: dts: sun8i: restore the inclusion of ccu headers in V3s DTSI

Icenowy Zheng icenowy at aosc.xyz
Sun Mar 5 14:37:05 CET 2017


When the V3s support patchset is applied, CCU headers and V3s DTSI went
into different trees, so the CCU inclusion is removed in the DTSI.

Add back them.

Signed-off-by: Icenowy Zheng <icenowy at aosc.xyz>
---
 arch/arm/boot/dts/sun8i-v3s.dtsi | 67 ++++++++++++++++++++--------------------
 1 file changed, 34 insertions(+), 33 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index 71075969e5e6..b3f8b7f9c0bb 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -40,6 +40,8 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/clock/sun8i-v3s-ccu.h>
+#include <dt-bindings/reset/sun8i-v3s-ccu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
@@ -55,7 +57,7 @@
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <0>;
-			clocks = <&ccu 14>;
+			clocks = <&ccu CLK_CPU>;
 		};
 	};
 
@@ -96,15 +98,15 @@
 		mmc0: mmc at 01c0f000 {
 			compatible = "allwinner,sun7i-a20-mmc";
 			reg = <0x01c0f000 0x1000>;
-			clocks = <&ccu 22>,
-				 <&ccu 45>,
-				 <&ccu 47>,
-				 <&ccu 46>;
+			clocks = <&ccu CLK_BUS_MMC0>,
+				 <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
 			clock-names = "ahb",
 				      "mmc",
 				      "output",
 				      "sample";
-			resets = <&ccu 7>;
+			resets = <&ccu RST_BUS_MMC0>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -115,15 +117,15 @@
 		mmc1: mmc at 01c10000 {
 			compatible = "allwinner,sun7i-a20-mmc";
 			reg = <0x01c10000 0x1000>;
-			clocks = <&ccu 23>,
-				 <&ccu 48>,
-				 <&ccu 50>,
-				 <&ccu 49>;
+			clocks = <&ccu CLK_BUS_MMC1>,
+				 <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
 			clock-names = "ahb",
 				      "mmc",
 				      "output",
 				      "sample";
-			resets = <&ccu 8>;
+			resets = <&ccu RST_BUS_MMC1>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -134,15 +136,15 @@
 		mmc2: mmc at 01c11000 {
 			compatible = "allwinner,sun7i-a20-mmc";
 			reg = <0x01c11000 0x1000>;
-			clocks = <&ccu 24>,
-				 <&ccu 51>,
-				 <&ccu 53>,
-				 <&ccu 52>;
+			clocks = <&ccu CLK_BUS_MMC2>,
+				 <&ccu CLK_MMC2>,
+				 <&ccu CLK_MMC2_OUTPUT>,
+				 <&ccu CLK_MMC2_SAMPLE>;
 			clock-names = "ahb",
 				      "mmc",
 				      "output",
 				      "sample";
-			resets = <&ccu 9>;
+			resets = <&ccu RST_BUS_MMC2>;
 			reset-names = "ahb";
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -153,8 +155,8 @@
 		usb_otg: usb at 01c19000 {
 			compatible = "allwinner,sun8i-h3-musb";
 			reg = <0x01c19000 0x0400>;
-			clocks = <&ccu 29>;
-			resets = <&ccu 17>;
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "mc";
 			phys = <&usbphy 0>;
@@ -169,9 +171,9 @@
 			      <0x01c1a800 0x4>;
 			reg-names = "phy_ctrl",
 				    "pmu0";
-			clocks = <&ccu 56>;
+			clocks = <&ccu CLK_USB_PHY0>;
 			clock-names = "usb0_phy";
-			resets = <&ccu 0>;
+			resets = <&ccu RST_USB_PHY0>;
 			reset-names = "usb0_reset";
 			status = "disabled";
 			#phy-cells = <1>;
@@ -198,7 +200,7 @@
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 37>, <&osc24M>, <&osc32k>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -213,6 +215,7 @@
 			uart0_pins_a: uart0 at 0 {
 				pins = "PB8", "PB9";
 				function = "uart0";
+				bias-pull-up;
 			};
 
 			mmc0_pins_a: mmc0 at 0 {
@@ -244,8 +247,8 @@
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 40>;
-			resets = <&ccu 49>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
 
@@ -255,8 +258,8 @@
 			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 41>;
-			resets = <&ccu 50>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
 
@@ -266,8 +269,8 @@
 			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 42>;
-			resets = <&ccu 51>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
 			status = "disabled";
 		};
 
@@ -275,10 +278,8 @@
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2ac00 0x400>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 38>;
-			resets = <&ccu 46>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&i2c0_pins>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -288,8 +289,8 @@
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2b000 0x400>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu 39>;
-			resets = <&ccu 47>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.11.1



More information about the Alsa-devel mailing list