[alsa-devel] [PATCH v4 06/15] soundwire: Add IO transfer

Vinod Koul vinod.koul at intel.com
Tue Dec 5 07:31:14 CET 2017


On Sun, Dec 03, 2017 at 09:01:41PM -0600, Pierre-Louis Bossart wrote:
> On 12/3/17 11:04 AM, Vinod Koul wrote:
> >On Fri, Dec 01, 2017 at 05:27:31PM -0600, Pierre-Louis Bossart wrote:

Sorry looks like I missed replying to this one earlier.

> >>>+static inline int find_response_code(enum sdw_command_response resp)
> >>>+{
> >>>+	switch (resp) {
> >>>+	case SDW_CMD_OK:
> >>>+		return 0;
> >>>+
> >>>+	case SDW_CMD_IGNORED:
> >>>+		return -ENODATA;
> >>>+
> >>>+	case SDW_CMD_TIMEOUT:
> >>>+		return -ETIMEDOUT;
> >>>+
> >>>+	default:
> >>>+		return -EIO;
> >>
> >>the 'default' case will handle both SDW_CMD_FAIL (which is a bus event
> >>usually due to bus clash or parity issues) and SDW_CMD_FAIL_OTHER (which is
> >>an imp-def IP event).
> >>
> >>Do they really belong in the same basket? From a debug perspective there is
> >>quite a bit of information lost.
> >
> >at higher level the error handling is same. the information is not lost as
> >it is expected that you would log it at error source.
> 
> I don't understand this. It's certainly not the same for me if you detect an
> electric problem or if the IP is in the weeds. Logging at the source is fine
> but this filtering prevents higher levels from doing anything different.

The point is higher levels like here cant do much than bail out and complain.

Can you point out what would be different behaviour in each of these cases?

> >>>+static inline int do_transfer(struct sdw_bus *bus, struct sdw_msg *msg)
> >>>+{
> >>>+	int retry = bus->prop.err_threshold;
> >>>+	enum sdw_command_response resp;
> >>>+	int ret = 0, i;
> >>>+
> >>>+	for (i = 0; i <= retry; i++) {
> >>>+		resp = bus->ops->xfer_msg(bus, msg);
> >>>+		ret = find_response_code(resp);
> >>>+
> >>>+		/* if cmd is ok or ignored return */
> >>>+		if (ret == 0 || ret == -ENODATA)
> >>
> >>Can you document why you don't retry on a CMD_IGNORED? I know there was a
> >>reason, I just can't remember it.
> >
> >CMD_IGNORED can be okay on broadcast. User of this API can retry all they
> >want!
> 
> So you retry if this is a CMD_FAILED but let higher levels retry for
> CMD_IGNORED, sorry I don't see the logic.

Yes that is right.

If I am doing a broadcast read, lets say for Device Id registers, why in the
world would I want to retry? CMD_IGNORED is a valid response and required to
stop enumeration cycle in that case.

But if I am not expecting a CMD_IGNORED response, I can very well go ahead
and retry from caller. The context is with caller and they can choose to do
appropriate handling.

And I have clarified this couple of times to you already, not sure how many
more times I would have to do that.

> >>Now that I think of it, the retry on TIMEOUT makes no sense to me. The retry
> >>was intended for bus-level issues, where maybe a single bit error causes an
> >>issue without consequences, but the TIMEOUT is a completely different beast,
> >>it's the master IP that doesn't answer really, a completely different case.
> >
> >well in those cases where you have blue wires, it actually helps :)
> 
> Blue wires are not supposed to change electrical behavior. TIMEOUT is only
> an internal SOC level issue, so no I don't get how this helps.
> 
> You have a retry count that is provided in the BIOS/firmware through disco
> properties and it's meant to bus errors. You are abusing the definitions. A
> command failed is supposed to be detected at the frame rate, which is
> typically 20us. a timeout is likely a 100s of ms value, so if you retry on
> top it's going to lock up the bus.

The world is not perfect! A guy debugging setups needs all the help. I do
not see any reason for not to retry. Bus is anyway locked up while a
transfer is ongoing (we serialize transfers).

Now if you feel this should be abhorred, I can change this for timeout.

> >>>+enum sdw_command_response {
> >>>+	SDW_CMD_OK = 0,
> >>>+	SDW_CMD_IGNORED = 1,
> >>>+	SDW_CMD_FAIL = 2,
> >>>+	SDW_CMD_TIMEOUT = 4,
> >>>+	SDW_CMD_FAIL_OTHER = 8,
> >>
> >>Humm, I can't recall if/why this is a mask? does it need to be?
> >
> >mask, not following!
> >
> >Taking a wild guess that you are asking about last error, which is for SW
> >errors like malloc fail etc...
> 
> no, I was asking why this is declared as if it was used for a bitmask, why
> not 0,1,2,3,4?

Oh okay, I think it was something to do with bits for errors, but don see it
helping so I can change it either way...

-- 
~Vinod


More information about the Alsa-devel mailing list