[alsa-devel] i.MX6 SGTL5000 hangs with EIO error
Ross Wille
audio at cornerbrick.com
Fri May 13 22:45:12 CEST 2016
Caleb,
Yes, it's a Jensen JT-11P-1HPC (10k 1:1) line transformer.
I have a custom isolation PC board, which includes the XLR jack, isolation
transformer, variable attenuator, and transient protection. The board has
separate "shield" and analog grounds. The output of this board feeds into
a standard, unmodified Wandboard via the 3.5mm LINEIN1 jack.
I'm not plugging/unplugging the Wandboard connector (well, I started out
that way, but the results were terrible). With the transformer and the TVS
diode the problem is MUCH better than it was initially. When I was driving
the LINEIN1 jack directly from the signal generator plugging/unplugging the
audio connector had a significant chance of making this happen.
Now, the isolation board is always connected to the Wandboard. And
plugging/unplugging the XLR connector is pretty reliable. The easiest way
I've found to make the problem happen is by keeping everything connected
and toggling the power switch on my signal generator repeatedly.
I don't think I'm getting any ESD during my tests, although when this device
gets put into service I'd expect to get some ESD when they plug into the
XLR jack while the device is powered. (Maybe I'll tell them not to do
that, but they're talking heads, not geeks.)
Most of the time a reboot fixes the problem, but I've seen rare occasions
when it does require a power cycle.
The SGTL5000 doesn't have an external reset. It has an internal reset
circuit which waits 8 clock cycles after power-on before it comes out of
reset. So, a hardware reset of this chip requires a power cycle.
There may be a way to force a software reset if I can still talk to the
chip, but if the chip is latched up only a power cycle is going to fix
that.
The LINEIN1 is capacitively coupled to the SGTL5000 (I assume that's because
the SGTL5000 input has a DC bias on it). I'm clamping +/-1V relative to
the Wandboard's signal ground, but that's on the AC-coupled side of the
signal. It'd be better to clamp it going into the codec as you've shown in
your sketch.
You asked where the TVS diode is located. It's a ESDARF01-1BM2 on the
custom isolation PCB and it's connected between signal and ground just
before it goes out the cable (which is only 6 inches long) and into the
Wandboard's LINEIN1 connector. It would definitely be better if the
protection was on the Wandboard itself, especially after the coupling
capacitor.
No, breathing on it doesn't affect it. :-) I can run all night with a
nearly full-swing sine wave at 1kHz and it never fails. It used to fail
regularly when I messed with the audio connections, but now it's much
harder to reproduce it.
Thanks again for all your thoughts and ideas. It's close to being good
enough, but it's not very professional for a piece of gear to stop working
just because someone plugged in an XLR cable.
-Ross
On Friday 13 May 2016 13:23, Caleb Crome wrote:
> On Fri, May 13, 2016 at 9:56 AM, Ross Wille <audio at cornerbrick.com> wrote:
>
> > Hi Caleb,
> >
> > Thank you for your response!
> >
> > The LINEIN1 protection on the Wandboard kicks in at around 5 to 5.5
Volts
> > and, as you pointed out, doesn't include a current-limiting resistor.
The
> > max-voltage range for the SGTL5000 audio input is spec'd at GND-0.3 to
> > Vdda+0.3. I believe the Wandboard Vdda is 2.5V, so the on-board
protection
> > is likely insufficient to limit the input voltage to the datasheet
specs.
> >
> > To mitigate this I have done the following:
> >
> > 1. I've isolated the audio between the signal generator and the codec
chip
> > using a professional-grade audio transformer having a breakdown voltage
of
> > 250 V RMS, so ground loops should not be an issue, but it might not
> > eliminate ESD completely.
> >
>
> Ah, a Jensen Transformer I assume? Those things are great. And the guy
> (Bill Whitlock) really knows about dealing with hum issues. His license
> plate reads MR CMRR. The DMV initially wouldn't give him that plate.
> Until he explained that CMRR stands for 'common-mode rejection ratio' :-)
> The stuff you learn at AES conventions...
>
>
> >
> > 2. For transient protection, I have a bidirectional TVS diode with a
> > breakdown voltage of 1.0V(typ) between the transformer output and
ground.
> > The TVS diode meets IEC 61000-4-2 for contact discharge of 8 kV and air
> > discharge of 15 kV and I don't believe its an ESD problem (see #3). The
> > circuit impedance at the TVS diode is about 10 kohms.
> >
>
>
>
> >
> > 3. I'm working on a static mat and I'm grounded.
> >
> > In spite of doing all this, I still get the error. If latch-up is the
> > culprit (which is possible) I am running out of things to try. I may
need
> > to add an active buffer stage to ensure the audio voltage never exceeds
the
> > voltage rails (but that'll require a new PCB design--sigh).
> >
>
> Is this your custom board + wandboard, or is it the standard wandboard?
>
> Is it possible that the GND of the audio connector (which is what should
> get hit first if you're plugging into the jack at the board side) isn't a
> very good ground, and is letting ESD couple to some other lines? ESD is
> icky that way. But, if you're ESD grounded, then this shouldn't be the
> issue anyway.
>
>
> >
> > I was hoping to find a software recovery solution because rebooting and
> > power-cycling the board are a rather drastic measures.
> >
>
> I doubt that's possible if a reset doesn't recover it -- it seems to be
> really broken if you need a power cycle. That's also a hint that it's
> latchup causing the problem.
>
>
>
> > Thanks!
> >
> > -Ross
> >
> >
> Looks like you've got most of it covered :-)
>
> Can you do some protection like this?
>
https://drive.google.com/file/d/0B0FeiEiLS9DzMVpTWm9QcDY5UHM/view?usp=sharing
>
> using something like a BAT54S? That should do a very good job of limiting
> the voltage to the codec. but, a 1V TVS should do the job too I think if
> it's placed on the wandboard. Where is your TVS diode placed? Soldered
in
> close on the connector of the wandboard, or floating out in space. But...
> ESD just shouldn't be the problem if you're properly grounded.
>
> What else could be the culprit I wonder? This happens as soon as you plug
> in, right? Does the problem ever happen when nobody is near by and
> breathing on it? Or is always in response to some body coming close and
> touching things?
>
> I'm kind of out of ideas without actually getting in close to it and
seeing
> what happens and when.
>
> Let me know if you can figure out any more details of when the problem
> happens. I just think it's got to be a hardware problem, but I've seen
> stranger things end up being software problems. :-)
>
> Cheers,
> -Caleb
>
>
>
> > On Thursday 12 May 2016 14:13, Caleb Crome wrote:
> > > On Thu, May 12, 2016 at 10:54 AM, Ross Wille <audio at cornerbrick.com>
> > wrote:
> > >
> > > > Hello all,
> > > >
> > > > I am doing an ALSA capture on a Wandboard Quad (i.MX6 quad core with
> > > > SGTL5000 codec chip) from the LINEIN1 jack. I'm using a
> > 4.6.0-rc3-armv7-x0
> > > > kernel.
> > > >
> > > > Sometimes when the audio glitches (for example, when I plug/unplug
the
> > > > audio
> > > > cable or adjust my signal generator) the snd_pcm_readi() function
will
> > > > start returning -5 (EIO).
> > > >
> > >
> > > This sounds like an ESD strike. (when you plug in the cable the ESD on
> > the
> > > cable wacks some electronics internally).
> > >
> > > See if you can ground yourself, the signal generator, the wand board,
and
> > > anything else with some ESD straps, and see if you can reproduce the
> > error.
> > >
> > >
> > > Looking at the wandboard baseboard, the linein1 jack *does* have ESD
> > > protection diodes on it.
> > >
> > > Interestingly, the mic1 jack does not have ESD diodes. not sure why.
> > >
> > > This shouldn't be a software issue, because there's no microphone
> > detection
> > > going on in hardware -- the software doesn't know you've inserted
> > anything.
> > >
> > >
> > > Another possibility is a different type of electrical over stress.
There
> > > might be a large voltage between your wandboard GND and generator GND.
> > > This is common, and is a result of the inter-widing capacitance on the
> > > respective 'isolated' power supplies. If that capacitance is large
> > enough,
> > > it might be able to drive enough current into the pins to wreck up the
> > > SGTL5000 until re-power. But... the wandboard's transient
suppression
> > > should be enough to deal with that.
> > >
> > > Oh, looking at the schematic again, there are TVS, diodes D36/D37, but
> > > there is *no* series resistance between the connector and the codec!
> > That
> > > could easily be the problem -- an external signal can drive lots of
(ac)
> > > current in through those lines and cause latch-up. That's why you
> > require
> > > a power off/on to reset it. Even a hard reset won't fix latchup.
> > >
> > > See if your codec starts to get warm when in this state :-/
Definitely
> > > damaging to the codec though.
> > >
> > > -Caleb
> > >
> > >
> > >
> > >
> > >
> > > >
> > > > Once this happens, the only way I've been able to recover is to
reboot
> > the
> > > > computer. Calling snd_pcm_close(), snd_pcm_prepare(),
snd_pcm_start(),
> > > > etc. doesn't help. When in this state, running arecord returns IO
> > errors
> > > > as well.
> > > >
> > > > It's interesting that, on rare occasions, I must do a power cycle in
> > order
> > > > to recover. When a reboot is not effective I've noticed that the
> > capture
> > > > device doesn't appear in /proc/asound/devices.
> > > >
> > > > I don't believe my specific ALSA settings are important, but I'm
> > calling
> > > > snd_pcm_readi() with ALSA set to a sample rate of 48000, format of
> > S16_LE,
> > > > channels=1, frames per period of 960 (20 mS periods), and 4 periods
per
> > > > buffer.
> > > >
> > > > This same problem happens on two different Wandboards, so I don't
think
> > > > it's
> > > > a defective board or chip. It has happened on older kernels as
well.
> > > >
> > > > Any ideas?
> > > >
> > > > Thank you!
> > > >
> > > > Ross Wille
> > > > _______________________________________________
> > > > Alsa-devel mailing list
> > > > Alsa-devel at alsa-project.org
> > > > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
> > > >
> > >
> >
>
More information about the Alsa-devel
mailing list