[alsa-devel] [PATCH 6/6] ARM: DTS: da850: Add McBSP0 and McBSP1

[Peter Ujfalusi]

On 04/07/16 15:55, Petr Kulhavy wrote:
> 
> 
> On 07.04.2016 14:45, Peter Ujfalusi wrote:
>> On 04/07/16 15:16, Petr Kulhavy wrote:
>>> On 07.04.2016 13:34, Peter Ujfalusi wrote:
>>>> On 04/06/16 16:21, Petr Kulhavy wrote:
>>>>> Add SoC nodes for McBSP0 and McBSP1 as well as the corresponding pinmux
>>>>> configurations.
>>>>>
>>>>> Signed-off-by: Petr Kulhavy <petr at barix.com>
>>>>> ---
>>>>>    arch/arm/boot/dts/da850.dtsi | 45
>>>>> +++++++++++++++++++++++++++++++++++++++++++-
>>>>>    1 file changed, 44 insertions(+), 1 deletion(-)
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
>>>>> index 5996e765e59c..9e2b1e97377c 100644
>>>>> --- a/arch/arm/boot/dts/da850.dtsi
>>>>> +++ b/arch/arm/boot/dts/da850.dtsi
>>>>> @@ -148,7 +148,24 @@
>>>>>                        0xc 0x88888888 0xffffffff
>>>>>                    >;
>>>>>                };
>>>>> -
>>>>> +            mcbsp0_pins: pinmux_mcbsp0_pins {
>>>>> +                pinctrl-single,bits = <
>>>>> +                    /* PINMUX2:
>>>>> +                    * CLKS0, DX0, DR0, FSX0
>>>>> +                    * FSR0, CLKX0, CLKR0
>>>>> +                    */
>>>>> +                    0x8 0x02222220 0xfffffff0
>>>>> +                >;
>>>>> +            };
>>>>> +            mcbsp1_pins: pinmux_mcbsp1_pins {
>>>>> +                pinctrl-single,bits = <
>>>>> +                    /* PINMUX1:
>>>>> +                    * CLKS1, DX1, DR1, FSX1,
>>>>> +                    * FSR1, CLKX1, CLKR1
>>>>> +                    */
>>>>> +                    0x4 0x22222220 0xfffffff0
>>>> This will conflict with the mcasp0_pins in da850-evm as AXR11 and AXR12 is
>>>> used by the board for audio. When I say conflict, I mean that audio will be
>>>> completely broken on the board.
>>> I agree with you, the EVM uses the pins for other peripherals. However I
>>> understand that the da850.dtsi is a generic description of the DA850 platform.
>>> Other DA850 based designs that use the McBSP will not have conflicts. For
>>> instance my two AM1808 based boards don't use the McASP.
>>> Of course the board's DTS must enable only non-conflicting peripherals/pinmux
>>> configurations.
>>> But having the pinmuxes defined does not break anything and actually helps
>>> creating the DTS file.
>> I think what the da850.dtsi does is wrong. The dtsi file should not set any
>> pinmux, those need to be set by the board .dts files If one board uses McASP0,
>> it will set up the pins for that and leave McBSP pins as they were, but other
>> board might use McBSP1 and not use McASP0, there you will have pincontrol for
>> McBSP1.
> It does not set the pinmux, it just defines the configurations.
> As far as I understand the pin configuration is applied when a node includes
> these two lines:
> 
>                         pinctrl-names = "default";
>                         pinctrl-0 = <&mcbspc0_pins>;

Yeah, true. just ignore my comment for the pinctrl part...

> 
> Petr
> 


-- 
Péter