[alsa-devel] [PATCH] ASoC: atmel: add wm8904 based audio machine driver

[Bo Shen]

Hi Mark,

On 07/18/2013 07:17 PM, Mark Brown wrote:
> On Thu, Jul 18, 2013 at 03:28:03PM +0800, Bo Shen wrote:
>> add wm8904 based audio machine driver
>>
>> the following ek board based on it
>>    - at91sam9n12ek
>>    - sama5d3xek (d31, d33, d34, d35)
>>
>> Signed-off-by: Bo Shen <voice.shen at atmel.com>
>
> Looks pretty good, a few fairly small issues below.
>
> The binding document should be CCed to devicetree-discuss for review.

OK, I will cc the devicetree-discuss next version.

>> +	atmel,audio-routing =
>> +		"Headphone Jack", "HPOUTL",
>> +		"Headphone Jack", "HPOUTR",
>> +		"IN2L", "Line In Jack",
>> +		"IN2R", "Line In Jack",
>> +		"Mic", "MICBIAS",
>> +		"IN1L", "Mic";
>
> The widgets defined by the board should be documented in this binding.
> Those from the CODEC should be documented in the CODEC binding.

OK, I will separate this and put need information in this binding document.

>> +#define MCLK_RATE 32768
>> +
>> +static struct clk *mclk;
>
> This should be in driver data for the board.  Shouldn't the clock be
> referenced using the clock bindings?

I will try to implement this in next version.

>> +static int atmel_asoc_wm8904_init(struct snd_soc_pcm_runtime *rtd)
>> +{
>> +	struct snd_soc_dai *codec_dai = rtd->codec_dai;
>> +	int ret;
>> +
>> +	ret = snd_soc_dai_set_sysclk(codec_dai, WM8904_CLK_FLL,
>> +			12000000, SND_SOC_CLOCK_IN);
>> +	if (ret < 0) {
>> +		pr_err("%s -failed to set wm8904 SYSCLK\n", __func__);
>> +		return ret;
>> +	}
>
> This is an odd thing to set the clock rate to and limits the sample
> rates the board can play back.  It would be better to set the clock rate
> based on the requested sample rate in hw_params - you're using the FLL
> so may as well take advantage of the ability it offers to support all
> sample rates.
>> +static int atmel_asoc_wm8904_params(struct snd_pcm_substream *substream,
>> +		struct snd_pcm_hw_params *params)
>> +{
>> +	struct snd_soc_pcm_runtime *rtd = substream->private_data;
>> +	struct snd_soc_dai *codec_dai = rtd->codec_dai;
>> +	int ret;
>> +
>> +	ret = snd_soc_dai_set_pll(codec_dai, WM8904_FLL_MCLK, WM8904_FLL_MCLK,
>> +		32768, params_rate(params) * 256);
>
> Ah, in fact you do actually do that - it'd be clearer to put the
> set_sysclk() after this.

OK, I will put set_sysclk here.

>> +	switch (level) {
>> +	case SND_SOC_BIAS_ON:
>> +	case SND_SOC_BIAS_PREPARE:
>> +		if (!mclk_on) {
>> +			ret = clk_prepare_enable(mclk);
>> +			if (ret == 0)
>> +				mclk_on = 1;
>> +		}
>> +		break;
>> +	case SND_SOC_BIAS_STANDBY:
>> +	case SND_SOC_BIAS_OFF:
>> +		if (mclk_on)
>> +			clk_disable_unprepare(mclk);
>> +		mclk_on = 0;
>> +		break;
>> +	}
>
> It's better to write this using the previous state than to have the
> mclk_on flag - you want to enable on the standby->prepare transition and
> disable on the standby->off transition.

OK, I will implement it in next version.

>> +static int atmel_asoc_wm8904_dt_init(struct platform_device *pdev)
>> +{
>> +	struct device_node *np = pdev->dev.of_node;
>> +	struct device_node *codec_np, *cpu_np;
>> +	struct snd_soc_card *card = &atmel_asoc_wm8904_card;
>> +	struct snd_soc_dai_link *dailink = &atmel_asoc_wm8904_dailink;
>> +	int ret;
>> +
>> +	if (!np)
>> +		return -1;
>
> Return a real error code here.

Sure.

Thanks,

Best Reards,
Bo Shen