[alsa-devel] [PATCH v2 00/14] OMAPDSS: HDMI: Prepare for DSS dev driver audio support and OMAP5
ricardo.neri at ti.com
Fri May 4 03:43:54 CEST 2012
This set of patches is intended to prepare the HDMI driver to implement the DSS
device driver interface for audio proposed here:
In preparation for that, it removes the current ASoC HDMI codec driver and
decouples HDMI audio build configuration from ASoC. Instead, a config option
may be selected by the parties interested in the HDMI audio functionality. While
the ASoC HDMI codec is removed, HDMI audio functionality restored in the last
patch of the series in the form of DSS audio support.
Also, this set prepares the HDMI driver for the introduction of the OMAP5 HDMI
audio functionality by further abstracting the portions of code that are
generic to all HDMI implementations (e.g, N/CTS params calculation). Also, an
IP-dependent audio configuration function is introduced as an HDMI IP operation;
this function takes IP-independent parameters and applies them as required by
For the specific case of OMAP4, the configuration of the IEC-60958 channel
status word is expanded to provide more flexibility. Also, some duplicated
IEC-60958 definitions are removed to, instead, reuse the definitions provided
by ALSA. Please note that this patches depend on the following patch adding
Without such patch, the patches in this series will not compile.
The changes for OMAP4 configuration expand the current support to cover more
audio sample rates: 32, 44.1, 48, 88.2, 176.4 and 192 kHz. Audio sample world
length of 16 through 24 bits as well as up to 8 audio channels.
These changes are based on the 3.4-rc5 kernel.
Validation was performed using Onkyo TX-SR508 and Yamaha RX-V367 AV receivers.
These are the changes with respect to v1:
*The DSS dev driver audio operations are, at the moment, protected using a
hardirq-safe spinlock. Except for the audio_start/stop functions, it was
concluded that a mutex could be used in the future is needed.
*In audio configuration, instead of parsing the IEC-60958 channel status word,
and setting bits individually, the word is passed directly to the IP. This
saves code, makes it more readable and fully configurable by the user.
*Split HDMI video_enable, audio_enable and audio_start into two separate
functions to enable/disable and start/stop. Also, update their return values.
*Audio channels are remapped to match the order preferred by ALSA's speaker-test.
*Remove OMAP4 HDMI IP configuration regarding High Bitrate audio and I2S
word select polarity, as this is not supported according to updated TI's
*Rename the lock of the HDMI panel.
*Remove unneeded header files.
*Rephrase the description of several patches.
Axel Castaneda Gonzalez (1):
OMAPDSS: HDMI: Decouple wrapper enable/disable and audio start/stop
Ricardo Neri (13):
OMAPDSS: HDMI: Split audio_enable into audio_enable/disable
OMAPDSS: HDMI: Split video_enable into video_enable/disable
OMAPDSS: HDMI: Remove ASoC codec
OMAPDSS: HDMI: OMAP4: Remove CEA-861 audio infoframe and IEC-60958
OMAPDSS: HDMI: OMAP4: Remove invalid I2S settings
OMAPDSS: HDMI: Decouple HDMI audio from ASoC
OMAPDSS: HDMI: OMAP4: Expand configuration for IEC-60958 audio
OMAPDSS: HDMI: Relocate N/CTS calculation
OMAPDSS: HDMI: Add support for more audio sample rates in N/CTS
OMAPDSS: HDMI: Add an audio configuration function
OMAPDSS: HDMI: OMAP4: Remap speaker order to match ALSA order
OMAPDSS: HDMI: Panel: Simplify the name of the HDMI mutex
OMAPDSS: HDMI: Implement DSS driver interface for audio
drivers/video/omap2/dss/Kconfig | 4 +
drivers/video/omap2/dss/dss.h | 8 +
drivers/video/omap2/dss/dss_features.c | 8 +-
drivers/video/omap2/dss/hdmi.c | 355 +++++++++++------------------
drivers/video/omap2/dss/hdmi_panel.c | 141 ++++++++++--
drivers/video/omap2/dss/ti_hdmi.h | 32 ++-
drivers/video/omap2/dss/ti_hdmi_4xxx_ip.c | 316 +++++++++++++++++++------
drivers/video/omap2/dss/ti_hdmi_4xxx_ip.h | 104 +---------
8 files changed, 537 insertions(+), 431 deletions(-)
More information about the Alsa-devel