[alsa-devel] [PATCH v3 1/9] davinci: EMAC support for Omapl138-Hawkboard

[Sergei Shtylyov]

Hello.

On 10/14/10 21:21, vm.rod25 at gmail.com wrote:

> From: Victor Rodriguez<vm.rod25 at gmail.com>

> This patch adds EMAC support for the Hawkboard-L138 system

> Signed-off-by: Victor Rodriguez<victor.rodriguez at sasken.com>
> ---
>   arch/arm/mach-davinci/board-omapl138-hawk.c |   49 +++++++++++++++++++++++++++
>   1 files changed, 49 insertions(+), 0 deletions(-)

> diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
> index c472dd8..3ae5178 100644
> --- a/arch/arm/mach-davinci/board-omapl138-hawk.c
> +++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
> @@ -19,6 +19,53 @@
>
>  #include<mach/cp_intc.h>
>  #include<mach/da8xx.h>
> +#include<mach/mux.h>
> +
> +#define HAWKBOARD_PHY_ID		"0:07"
> +
> +static short omapl138_hawk_mii_pins[] __initdata = {
> +	DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
> +	DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
> +	DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
> +	DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
> +	DA850_MDIO_D,
> +	-1
> +};
> +
> +static int __init omapl138_hawk_config_emac(void)
> +{
> +	void __iomem *cfgchip3;
> +	int ret;
> +	u32 val;
> +	struct davinci_soc_info *soc_info =&davinci_soc_info;
> +
> +	if (!machine_is_omapl138_hawkboard())
> +		return 0;
> +
> +	cfgchip3 = DA8XSYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);

    Could be initializer...

> +	val = __raw_readl(cfgchip3);
> +
> +	val &= ~BIT(8);
> +	ret = davinci_cfg_reg_list(omapl138_hawk_mii_pins);
> +	pr_info("EMAC: MII PHY configured\n");

    I think this pr_info() should follow __raw_writel() call.

> +	if (ret)
> +		pr_warning("%s: "
> +			"cpgmac/mii mux setup failed: %d\n", __func__, ret);

    You should return here.

> +
> +	/* configure the CFGCHIP3 register for MII */
> +	__raw_writel(val, cfgchip3);
> +
> +	soc_info->emac_pdata->phy_id = HAWKBOARD_PHY_ID;
> +
> +	ret = da8xx_register_emac();
> +	if (ret)
> +		pr_warning("%s: "
> +			"emac registration failed: %d\n", __func__, ret);
> +	return 0;

    Why this function returns anything at all if it'a always 0, and the result 
is ignored?

> @@ -30,6 +77,8 @@ static __init void omapl138_hawk_init(void)
>
>   	davinci_serial_init(&omapl138_hawk_uart_config);
>
> +	ret = omapl138_hawk_config_emac();

    Why assign 'ret', if you're ignoring the result?

> +
>   	ret = da8xx_register_watchdog();
>   	if (ret)
>   		pr_warning("omapl138_hawk_init: "

WBR, Sergei