[alsa-devel] HP pavilion dv5 1110ew - no hdmi sound

Bartłomiej Holdenmayer bh at habah.com
Sat Feb 14 21:19:57 CET 2009


Dnia 2009-02-14, sob o godzinie 18:03 +0100, Takashi Iwai pisze:
> At Sat, 14 Feb 2009 15:53:26 +0100,
> Bartłomiej Holdenmayer wrote:
> > 
> > Dnia 2009-02-14, sob o godzinie 15:28 +0100, Vedran Miletić pisze:
> > > On Sat, Feb 14, 2009 at 3:22 PM, Bartłomiej Holdenmayer <bh at habah.com> wrote:
> > > > I am not sure if do everything properly.
> > > >
> > > > 1. I did installation of alsa snap with script
> > > > AlsaUpgrade-1.0.x-rev-1.16.sh;
> > > >
> > > > 2. After that, I changed last line in /etc/modprobe.d/alsa-base from:
> > > > options snd-hda-intel enable_msi=1
> > > >
> > > > into:
> > > > options snd-hda-intel enable_msi=1 probe_mask=0x1ff
> > > >
> > > >
> > > > 3. After I restarted alsa with  /etc/init.d/alsasound stop
> > > > and
> > > > /etc/init.d/alsasound start
> > > >
> > > > and get message:
> > > > Starting sound driver: snd-hda-intel done
> > > >
> > > > Am I doing that properly? What should I do (what command) to see
> > > > hda_intel: codec_mask forced to 0xff
> > > >
> > > >
> > > > --
> > > > Pozdrawiam / Regards
> > > > Bartłomiej Holdenmayer
> > > >
> > > > GG:541634; ICQ:33920811; skypename:bartlomiejholdenmayer
> > > >
> > > > _______________________________________________
> > > > Alsa-devel mailing list
> > > > Alsa-devel at alsa-project.org
> > > > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
> > > >
> > > 
> > > Did you try installing snapshot manually? Script could be bad.
> > > 
> > > Vedran
> > > _______________________________________________
> > > Alsa-devel mailing list
> > > Alsa-devel at alsa-project.org
> > > http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
> > 
> > I checked script. It is downloading good snapshot.
> > 
> > There are other options in script:
> > ./configure --with-kernel=/usr/src/linux-headers-$KERNEL
> > --with-cards=all --with-card-options=all --with-sequencer=yes
> > --with-oss=yes --prefix=/usr || die "$DRIVER configure failed"
> > 
> > I guess everything is ok. I attach the script.
> 
> After you load the latest driver with that probe_mask option, check
> the "kernel messages" (i.e. run dmesg command).  It's not about the
> message from modprobe.
> 
> 
> Takashi
> _______________________________________________
> Alsa-devel mailing list
> Alsa-devel at alsa-project.org
> http://mailman.alsa-project.org/mailman/listinfo/alsa-devel

How to load the latest driver with that probe_mask option
-- 
Pozdrawiam / Regards
Bartłomiej Holdenmayer

GG:541634; ICQ:33920811; skypename:bartlomiejholdenmayer



More information about the Alsa-devel mailing list